|
|
Número de pieza | ICX055AL | |
Descripción | 1/3-inch CCD Image Sensor | |
Fabricantes | Sony Corporation | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de ICX055AL (archivo pdf) en la parte inferior de esta página. Total 17 Páginas | ||
No Preview Available ! ICX055AL
ww1w./D3ata-Sihneect4hU.coCmCD Image Sensor for CCIR B/W Camera
For the availability of this product, please contact the sales office.
Description
The ICX055AL is an interline CCD solid-state
image sensor suitable for CCIR 1/3-inch B/W video
16 pin DIP (Plastic)
cameras. High sensitivity is achieved through the
adoption of HAD (Hole-Accumulation Diode) sensors.
This chip features a field period readout system,
and an electronic shutter with variable charge-
storage time.
Features
• High sensitivity (+3dB compare with ICX045BLA)
and low dark current
• Continuous variable-speed shutter
1/50s (Typ.), 1/120s to 1/10000s
• Low smear
• Excellent antiblooming characteristics
• Horizontal register: 5V drive
• Reset gate:
5V drive
Pin 1
V
7
H 30
Pin 9
Device Structure
• Optical size:
1/3-inch format
Optical black position
(Top View)
• Number of effective pixels: 500 (H) × 582 (V) approx. 290K pixels
• Number of total pixels: 537 (H) × 597 (V) approx. 320K pixels
• Interline CCD image sensor
• Chip size:
6.00mm (H) × 4.96mm (V)
• Unit cell size:
9.8µm (H) × 6.3µm (V)
• Optical black:
Horizontal (H) direction: Front 7 pixels, Rear 30 pixels
Vertical (V) direction: Front 14 pixels, Rear 1 pixel
• Number of dummy bits: Horizontal 16
Vertical 1 (even field only)
• Substrate material:
Silicon
1
14
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
–1–
E92832F66-ST
1 page ICX055AL
Cwlwowc.kDaEtaqSuhieveat4leUn.ctomCircuit Constant
Item
Capacitance between vertical transfer
clock and GND
Capacitance between vertical transfer
clocks
Capacitance between horizontal
transfer clock and GND
Capacitance between horizontal
transfer clocks
Capacitance between reset gate clock
and GND
Capacitance between substrate clock
and GND
Vertical transfer clock series resistor
Vertical transfer clock ground resistor
Horizontal transfer clock series resistor
Reset gate clock series resistor
Symbol
CφV1, CφV3
CφV2, CφV4
CφV12, CφV34
CφV23, CφV41
CφV13
CφV24
CφH1, CφH2
CφHH
CφRG
CφSUB
R1, R3
R2, R4
RGND
RφH
RφRG
Vφ1 Vφ2
Min. Typ. Max. Unit Remarks
1500
pF
820 pF
470 pF
230 pF
150 pF
230 pF
47 pF
47 pF
5 pF
320 pF
51 Ω
100 Ω
15 Ω
10 Ω
40 Ω
R1 CφV12
R2
CφV41
CφV1
CφV2
CφV23
CφV24
R4
CφV4 RGND CφV3
CφV34
CφV13
R3
RφH
Hφ1
CφH1
CφHH
RφH
Hφ2
CφH2
Vφ4 Vφ3
Vertical transfer clock equivalent circuit
Horizontal transfer clock equivalent circuit
RGφ
RφRG
CφRG
Reset gate clock equivalent circuit
–5–
5 Page ICX055AL
6w. wDwa.DrkatasSighneaetl4sUh.caodming
After measuring 5, measure the maximum (Vdmax [mV]) and minimum (Vdmin [mV]) values of the dark
signal output and substitute the values into the following formula.
∆Vdt = Vdmax – Vdmin [mV]
7. Flicker
Set to standard imaging condition II. Adjust the luminous intensity so that the average value of the signal
output is 200mV, and then measure the difference in the signal level between fields (∆Vf [mV]). Then
substitute the value into the following formula.
F = (∆Vf/200) × 100 [%]
8. Lag
Adjust the signal output value generated by strobe light to 200mV. After setting the strobe light so that it
strobes with the following timing, measure the residual signal (Vlag). Substitute the value into the following
formula.
Lag = (Vlag/200) × 100 [%]
FLD
SG1
Strobe light
timing
Output
Light
Signal output 200mV Vlag (lag)
– 11 –
11 Page |
Páginas | Total 17 Páginas | |
PDF Descargar | [ Datasheet ICX055AL.PDF ] |
Número de pieza | Descripción | Fabricantes |
ICX055AK | 1/3-inch CCD Image Sensor | Sony Corporation |
ICX055AL | 1/3-inch CCD Image Sensor | Sony Corporation |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |