DataSheet.es    


PDF ICX054BL Data sheet ( Hoja de datos )

Número de pieza ICX054BL
Descripción Diagonal 6mm (Type 1/3) CCD Image Sensor
Fabricantes Sony Corporation 
Logotipo Sony Corporation Logotipo



Hay una vista previa y un enlace de descarga de ICX054BL (archivo pdf) en la parte inferior de esta página.


Total 18 Páginas

No Preview Available ! ICX054BL Hoja de datos, Descripción, Manual

ICX054BL
wwDw.DiaatgaSohneeat4lU.6comm m (Type 1/3) CCD Image Sensor for EIA B/W Video Cameras
Description
The ICX054BL is an interline CCD solid-state image
sensor suitable for EIA B/W video cameras.
Compared with the current product ICX054AL,
sensitivity is improved drastically through the adoption
of Super HAD CCD technology.
This chip features a field period readout system, and
an electronic shutter with variable charge-storage
time.
16 pin DIP (Plastic)
Features
High sensitivity (+4dB at F8, +2dB at F1.2 compared with ICX054AL)
High saturation signal (+1dB compared with ICX054AL)
Low smear and low dark current
Excellent antiblooming characteristics
Continuous variable-speed shutter
Horizontal register: 5V drive
Reset gate:
5V drive
V
2
Pin 9
Pin 1
H 25
Device Structure
Interline CCD image sensor
Optical black position
(Top View)
Image size:
Diagonal 6mm (Type 1/3)
Number of effective pixels: 510 (H) × 492 (V) approx. 250K pixels
Number of total pixels:
537 (H) × 505 (V) approx. 270K pixels
Chip size:
6.00mm (H) × 4.96mm (V)
Unit cell size:
9.6µm (H) × 7.5µm (V)
Optical black:
Horizontal (H) direction: Front 2 pixels, Rear 25 pixels
Vertical (V) direction:
Front 12 pixels, Rear 1 pixel
Number of dummy bits: Horizontal 16
Vertical 1 (even field only)
Substrate material:
Silicon
1
12
Super HAD CCD is a registered trademark of Sony Corporation. Super HAD CCD is a CCD that drastically improves sensitivity by introducing newly
developed semiconductor technology by Sony Corporation into Sony's high-performance HAD (Hole-Accumulation Diode) sensor.
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
–1–
E98223A99

1 page




ICX054BL pdf
ICX054BL
Cwlowcwk.DEatqaSuhiveeatl4eUn.ctoCmircuit Constant
Item
Capacitance between vertical transfer
clock and GND
Capacitance between vertical transfer
clocks
Capacitance between horizontal
transfer clock and GND
Capacitance between horizontal
transfer clocks
Capacitance between reset gate clock
and GND
Capacitance between substrate clock
and GND
Vertical transfer clock series resistor
Vertical transfer clock ground resistor
Horizontal transfer clock series resistor
Reset gate clock series resistor
Symbol
CφV1, CφV3
CφV2, CφV4
CφV12, CφV34
CφV23, CφV41
CφV13
CφV24
CφH1, CφH2
CφHH
CφRG
CφSUB
R1, R3
R2, R4
RGND
RφH
RφRG
Vφ1 Vφ2
Min. Typ. Max. Unit Remarks
1500
pF
820 pF
470 pF
230 pF
150 pF
230 pF
47 pF
47 pF
5 pF
320 pF
51
100
15
10
40
CφV12
R1
R2
CφV41
CφV1
CφV2
CφV23
CφV24
R4
CφV4 RGND CφV3
CφV34
CφV13
R3
RφH
Hφ1
CφH1
CφHH
RφH
Hφ2
CφH2
Vφ4 Vφ3
Vertical transfer clock equivalent circuit
Horizontal transfer clock equivalent circuit
RGφ
RφRG
CφRG
Reset gate clock equivalent circuit
–5–

5 Page





ICX054BL arduino
ICX054BL
6w. wDwa.DrkatasSighneeatl4sUh.caodming
After measuring 5, measure the maximum (Vdmax [mV]) and minimum (Vdmin [mV]) values of the dark
signal output and substitute the values into the following formula.
Vdt = Vdmax – Vdmin [mV]
7. Flicker
Set to standard imaging condition II. Adjust the luminous intensity so that the average value of the signal
output is 200mV, and then measure the difference in the signal level between fields (Vf [mV]). Then
substitute the value into the following formula.
F = (Vf/200) × 100 [%]
8. Lag
Adjust the signal output value generated by strobe light to 200mV. After setting the strobe light so that it
strobes with the following timing, measure the residual signal (Vlag). Substitute the value into the following
formula.
Lag = (Vlag/200) × 100 [%]
FLD
SG1
Strobe light
timing
Output
Light
Signal output 200mV Vlag (lag)
– 11 –

11 Page







PáginasTotal 18 Páginas
PDF Descargar[ Datasheet ICX054BL.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
ICX054BKDiagonal 6mm (Type 1/3) CCD Image SensorSony Corporation
Sony Corporation
ICX054BLDiagonal 6mm (Type 1/3) CCD Image SensorSony Corporation
Sony Corporation

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar