|
|
Número de pieza | DS1815 | |
Descripción | 3.3V EconoReset | |
Fabricantes | Dallas Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de DS1815 (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
No Preview Available ! www.DataSheet4U.com
www.dalsemi.com
DS1815
3.3V EconoReset with Push-Pull Output
FEATURES
Automatically restarts a microprocessor after
power failure
Maintains reset for 150 ms after VCC returns
to an in-tolerance condition
Reduces need for discrete components
Precision temperature-compensated voltage
reference and voltage sensor
Accurate 5%, 10% or 20% power monitoring
Low-cost TO-92 or space saving surface-
mount SOT-23 packages available
Push-pull output for low current operation
Operating temperature -40°C to +85°C
PIN ASSIGNMENT
3
12
SOT-23 PACKAGE
123
123
TO-92 PACKAGE
See Mech.
Drawings Section
PIN DESCRIPTION
TO-92
1 RST
2 VCC
3 GND
Active Low Reset Output
Power Supply
Ground
SOT-23
1 RST
2 VCC
3 GND
Active Low Reset Output
Power Supply
Ground
DESCRIPTION
The DS1815 EconoReset uses a precision temperature reference and comparator circuit to monitor the
status of the power supply (VCC). When an out-of-tolerance condition is detected, an internal power-fail
signal is generated which forces reset to the active state. When VCC returns to an in-tolerance condition,
the reset signal is kept in the active state for approximately 150 ms to allow the power supply and
processor to stabilize.
1 of 5
111999
1 page NOTES:
1. All voltages are referenced to ground.
2. wMwwe.DasautarSehdeewt4Uit.hcoVm CC ≥ 2.7V.
DS1815
3. Measured with RST output open.
4. Measured with 2.7V ≤ VCC ≤ 3.3V.
5. tR = 5 µs.
6. The tF value is for reference in defining values for TRPD and should not be considered a requirement
for proper operation or use of the device.
PART MARKING CODES
“A”, “B”, &“C” represent the device type.
810 . . . . DS1810
811 . . . . DS1811
812 . . . . DS1812
813 . . . . DS1813
815 . . . . DS1815
816 . . . . DS1816
817 . . . . DS1817
818 . . . . DS1818
“D” represents the device tolerance.
A . . . . . . 5%
B . . . . . . 10%
C . . . . . . 15%
D . . . . . . 20%
5 of 5
5 Page |
Páginas | Total 5 Páginas | |
PDF Descargar | [ Datasheet DS1815.PDF ] |
Número de pieza | Descripción | Fabricantes |
DS1810 | 5V EconoReset | Dallas Semiconductor |
DS1811 | 5V EconoReset | Dallas Semiconductor |
DS1812 | 5V EconoReset | Dallas Semiconductor |
DS1813 | 5V EconoReset | Dallas Semiconductor |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |