|
|
Número de pieza | SA9259 | |
Descripción | 5-Channel BTL Driver | |
Fabricantes | Silan | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de SA9259 (archivo pdf) en la parte inferior de esta página. Total 10 Páginas | ||
No Preview Available ! SA9259
5-CH BTL DRIVER FOR CD PLAYER WITH 5V OUTPUT VOLTAGE
DESCRIPTION
The SA9259 is a 5-channel motor driver for driving focus actuator,
tracking actuator, sled motor, spindle motor and loading motor in
products such as CD-PLAYER/VIDEO-CD drivers.
FEATURES
* Wide operating supply voltage range: 6V~13.2V
www.DataSheet4U.com* Thermal shutdown circuit on chip
* Built-in 5V regulator controller.
* Level shift circuit on chip.
* Built-in Mute mode.
* Built-in Loading motor speed control circuit.
* Built-in 1 phase, full-wave, linear DC motor driver.
HSOP-28-375-0.8
APPLICATIONS
* CD-PLAYER
* VIDEO-CD
* CAR-CD
ORDERING INFORMATION
Device
Package
SA9259
HSOP-28-375-0.8
BLOCK DIAGRAM
ABSOLUTE MAXIMUM RATINGS (Tamb=25°C)
Characteristics
Maximum supply voltage
Power dissipation
Operating temperature
Storage temperature
Maximum current output
Symbol
VCCMAX
PD
TOPR
TSTG
IOMAX
HANGZHOU SILAN MICROELECTRONICS CO.,LTD
Http: www.silan.com.cn
Rating
18
@1.7
-40~+85
-55~+150
1
Unit
V
W
°C
°C
A
REV:1.3 2007.01.26
Page 1 of 10
1 page SA9259
• Periphery circuit is composed of bipolar, KSB722 and one 100µF capacitor. The capacitor needs good
temperature characteristics to remove the ripple.
•The output voltage VOUT is decided by the following formula:
VOUT = VREF BG (R2 + R3) / R3 = 2.5 X 2 = 5V
R2 = R3
3. LOADING MOTOR DRIVER
www.DataSheet4U.com
•Input voltage (5V and 0V or 0V and 5V to pin 9 and pin 14.
•After input the voltage to pin 9 and pin 14, decide the output of comparator according to the voltage state.
•As the above figure, the voltage warp ∆V, [VREF1 + (I x R)] - [VREF1 -(I x R)], used for the motor. And the
direction of the motor is decided by the voltage warp +∆V and -∆V.
•The output characteristics are as follows:
FWD(pin9)
REV(pin14)
VOTR+(pin15)
VOTR-(pin16)
Function
L
L
(Vcc –Vbe) / 2
(Vcc –Vbe) / 2
Stop mode
L H L H Reverse mode
H L H L Forward mode
H
H
(Vcc –Vbe) / 2
(Vcc –Vbe) / 2
Stop mode
4. LOADING MOTOR SPEED CONTROL
VCC(8V)
50K
R
4V 20
50K
VCC
VCC(8V)
4V
50K
20
50K
R
VCC
•If the torque of the loading motor is too low when it is used with the pin #20 open, then it should be used as the
above diagram.
•The desired torque could be obtained by selecting the appropriate resistor R as shown in the left diagram.
•If it is necessary, the zener diode can be used as in the right diagram.
•The maximum torque is obtained when the applied voltage at pin #20 is about 6.8V (at VCC=8V).
5. Connect a by-pass capacitor, 0.1µF between the supply voltage source.
VCC2 22
VCC1 21
104
HANGZHOU SILAN MICROELECTRONICS CO.,LTD
Http: www.silan.com.cn
REV:1.3 2007.01.26
Page 5 of 10
5 Page |
Páginas | Total 10 Páginas | |
PDF Descargar | [ Datasheet SA9259.PDF ] |
Número de pieza | Descripción | Fabricantes |
SA9258 | 4-CH BTL DRIVER | Silan Microelectronics |
SA9259 | 5-Channel BTL Driver | Silan |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |