DataSheet.es    


PDF TDA7575PD Data sheet ( Hoja de datos )

Número de pieza TDA7575PD
Descripción MULTIFUNCTION DUAL BRIDGE POWER AMPLIFIER
Fabricantes STMicroelectronics 
Logotipo STMicroelectronics Logotipo



Hay una vista previa y un enlace de descarga de TDA7575PD (archivo pdf) en la parte inferior de esta página.


Total 17 Páginas

No Preview Available ! TDA7575PD Hoja de datos, Descripción, Manual

TDA7575PD
MULTIFUNCTION DUAL BRIDGE POWER AMPLIFIER
WITH INTEGRATED DIGITAL DIAGNOSTICS
DMOS POWER OUTPUT
NON-SWITCHING HI-EFFICIENCY
SINGLE-CHANNEL 1DRIVING CAPABILITY
www.DataSheet4U.coHmIGH OUTPUT POWER CAPABILITY 2x28W/
4@ 14.4V, 1KHZ, 10% THD, 2x40W/4EIAJ
MAX. OUTPUT POWER 2x75W/2Ω, 1x150W/1
SINGLE-CHANNEL 1DRIVING CAPABILITY
– 84W UNDISTORTED POWER
– FULL I2C BUS DRIVING WITH 4 ADDRESS
POSSIBILITIES:
– ST-BY, PLAY/MUTE, GAIN 12/26dB, FULL
DIGITAL DIAGNOSTIC
POSSIBILITY TO DISABLE THE I2C
DIFFERENTAL INPUTS
FULL FAULT PROTECTION
DC OFFSET DETECTION
TWO INDEPENDENT SHORT CIRCUIT
PROTECTIONS
CLIPPING DETECTOR PIN WITH
SELECTABLE THRESHOLD (2%/10%)
ST-BY/MUTE PINS
DESCRIPTION
The TDA7575PD is a new BCD technology DUAL
BRIDGE type of car radio amplifier in PowerSO36
package specially intended for car radio applications.
Thanks to the DMOS output stage the TDA7575PD
MULTIPOWER BCD TECHNOLOGY
MOSFET OUTPUT POWER STAGE
PowerSO36 (Slug up)
ORDERING NUMBER: TDA7575PD
has a very low distortion allowing a clear powerful
sound. Among the features, its superior efficiency
performance coming from the internal exclusive
structure, makes it the most suitable device to simpli-
fy the thermal management in high power sets.The
dissipated output power under average listening con-
dition is in fact reduced up to 50% when compared to
the level provided by conventional class AB solu-
tions.
This device is equipped with a full diagnostic array
that communicates the status of each speaker
through the I2C bus. The TDA7575PD has also the
possibility of driving loads down to 1paralleling the
outputs into a single channel. It is also possible to dis-
able the I2C and control the TDA7575PD by means of
the usual ST-BY and MUTE pins.
BLOCK DIAGRAM
ADDRESS
A B CLK DATA
VS
VCC
CD_OUT
IN1+
IN1-
I2CBUS
IN2+
CLIP
DETECTOR
SHORT CIRCUIT
PROTECTION
OUT1+
OUT1-
OUT2+
IN2- OUT2-
SHORT CIRCUIT
PROTECTION
I2C EN
March 2004
SVR ST-BY/HE S_GND PW_GND TAB 1MUTE
D01AU1269
1/17

1 page




TDA7575PD pdf
TDA7575PD
ELECTRICAL CHARACTERISTCS: (continued)
Symbol
Parameter
Test Condition
Min. Typ. Max. Unit
ICDL Clip Pin Low Sink Current
CD Clip detect THD level
CD on; VCD < 300mV
D0 (IB1) = 0
1 mA
0.8 1.3 2.5
%
D0 (IB1) = 1
5 10 15 %
(*) ST-BY Pin high enables I2C bus; ST-BY Pin low puts the device in ST-BY condition.(see “prog” for more details)
TURN ON DIAGNOSTICS (Power Amplifier Mode)
Pgnd
www.DataSheet4U.com
Short to GND det. (below this Power Amplifier in st-by condition
limit, the Output is considered in
Short Circuit to GND)
1.2 V
Pvs Short to Vs det. (above this
limit, the Output is considered in
Short Circuit to VS)
Vs -0.9
V
Pnop
Normal operation
thresholds.(Within these limits,
the Output is considered
without faults).
1.8 Vs -1.5 V
Lsc
Lop
Lnop
Shorted Load det.
Open Load det.
Normal Load det.
0.5
130
1.5 70
TURN ON DIAGNOSTICS (Line Driver Mode)
Pgnd
Short to GND det. (below this Power Amplifier in st-by
limit, the Output is considered in
Short Circuit to GND)
1.2 V
Pvs Short to Vs det. (above this
limit, the Output is considered in
Short Circuit to VS)
Vs -0.9
V
Pnop
Normal operation
thresholds.(Within these limits,
the Output is considered
without faults).
1.8 Vs -1.5 V
Lsc
Lop
Lnop
Shorted Load det.
Open Load det.
Normal Load det.
1.5
400
4.5 200
PERMANENT DIAGNOSTICS (Power Amplifier Mode or Line Driver Mode)
Pgnd
Short to GND det. (below this Power Amplifier in Mute or Play
limit, the Output is considered in condition, one or more short circuits
Short Circuit to GND)
protection activated
1.2 V
Pvs Short to Vs det. (above this
limit, the Output is considered in
Short Circuit to VS)
Vs - 0.9
V
Pnop
Normal operation
thresholds.(Within these limits,
the Output is considered
without faults).
1.8 Vs -1.5 V
Lsc Shorted Load det.
Pow. Amp. mode
0.5
Line Driver mode
1.5
5/17

5 Page





TDA7575PD arduino
Examples of bytes sequence
1 - Turn-On diagnostic - Write operation
Start Address byte with D0 = 0
TDA7575PD
ACK IB1 with D6 = 1 ACK IB2 ACK STOP
2 - Turn-On diagnostic - Read operation
Start Address byte with D0 = 1
ACK DB1 ACK DB2 ACK STOP
The delay from 1 to 2 can be selected by software, starting from T.B.D. ms
www.DataSheet4U.com
3a - Turn-On of the power amplifier with mute on, diagnostic defeat.
Start Address byte with D0 = 0
ACK IB1 ACK IB2 ACK STOP
X000XXXX
XXX1XX1X
3b - Turn-Off of the power amplifier
Start Address byte with D0 = 0
ACK IB1 ACK IB2 ACK STOP
X0XXXXXX
XXX0XXXX
4 - Offset detection procedure enable
Start Address byte with D0 = 0
ACK IB1 ACK IB2 ACK STOP
XX1XX1XX
XXX1XXXX
5 - Offset detection procedure stop and reading operation (the results are valid only for the offset detection bits
(D2 of the bytes DB1, DB2, DB3, DB4).
Start Address byte with D0 = 1
ACK
DB1
ACK
DB2
ACK STOP
The purpose of this test is to check if a D.C. offset (2V typ.) is present on the outputs, produced by input
capacitor with anomalous leackage current or humidity between pins.
The delay from 4 to 5 can be selected by software, starting from T.B.D. ms
DIAGNOSTICS FUNCTIONAL DESCRIPTION:
a) TURN-ON DIAGNOSTIC.
It is activated at the turn-on (stand-by out) under I2C bus request. Detectable output faults are:
– SHORT TO GND
– SHORT TO Vs
– SHORT ACROSS THE SPEAKER
– OPEN SPEAKER
To verify if any of the above misconnections are in place, a subsonic (inaudible) current pulse (fig. A) is internally
generated, sent through the speaker(s) and sunk back.The Turn On diagnostic status is internally stored until a
successive diagnostic pulse is requested (after a I2C reading).
If the "stand-by out" and "diag. enable" commands are both given through a single programming step, the pulse
takes place first (power stage still in stand-by mode, low, outputs= high impedance).
11/17

11 Page







PáginasTotal 17 Páginas
PDF Descargar[ Datasheet TDA7575PD.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
TDA7575PDMULTIFUNCTION DUAL BRIDGE POWER AMPLIFIERSTMicroelectronics
STMicroelectronics

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar