|
|
Número de pieza | M29DW128G | |
Descripción | Flash memory | |
Fabricantes | Numonyx | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de M29DW128G (archivo pdf) en la parte inferior de esta página. Total 11 Páginas | ||
No Preview Available ! M29DW128G
128 Mbit (8 Mb x 16, multiple bank, page, dual boot)
3 V supply Flash memory
Data Brief
Features
■ Supply voltage
www.DataSheet4U.com– VCC = 2.7 to 3.6 V for Program, Erase and
Read
– VPP =12 V for Fast Program (optional)
■ Asynchronous Random/Page Read
– Page width: 8 words
– Page access: 25 ns
– Random access: 60 ns
■ Programming time
– 15 µs per byte/word (typical)
– 32-word write buffer
■ Erase verify
■ Memory blocks
– Quadruple bank memory array:
16 Mbit+48 Mbit+48 Mbit+16 Mbit
– Parameter blocks (at top and bottom)
■ Dual operation
– While Program or Erase in one bank, Read
in any of the other banks
■ Program/Erase Suspend and Resume modes
– Read from any block during Program
Suspend
– Read and Program another block during
Erase Suspend
■ Unlock Bypass Program
– Faster production/batch programming
■ Common Flash interface
– 64 bit security code
■ 100,000 Program/Erase cycles per block
TSOP56 (NF)
14 x 20 mm
BGA
TBGA64 (ZA)
10 x 13 mm
■ Low power consumption
– Standby and automatic standby
■ Hardware block protection
– VPP/WP pin for fast program and write
protect of the four outermost parameter
blocks
■ Security features
– Standard protection
– Password protection
– Additional block protection
■ Extended memory block
– Extra block used as security block or to
store additional information
■ Electronic signature
– Manufacturer code: 0020h
– Device code: 227Eh+2220h+2200h
■ ECOPACK® packages available
December 2007
Rev 2
For further information contact your local STMicroelectronics sales office.
1/11
www.numonyx.com
1
1 page M29DW128G
1 Description
Description
www.DataSheet4U.com
The M29DW128G is a 128 Mbit (8 Mb x 16) non-volatile memory that can be read, erased
and reprogrammed. These operations can be performed using a single low voltage (2.7 to
3.6 V) supply. At Power-up the memory defaults to its Read mode.
The M29DW128G features an asymmetrical block architecture, with 8 parameter and 62
main blocks, divided into four banks, A, B, C and D, providing multiple bank operations.
While programming or erasing in one bank, read operations are possible in any other bank.
The bank architecture is summarized in Table 2. Four of the parameter blocks are at the top
of the memory address space, and four are at the bottom.
Program and Erase commands are written to the command interface of the memory. An on-
chip Program/Erase controller simplifies the process of programming or erasing the memory
by taking care of all of the special operations that are required to update the memory
contents. The end of a program or erase operation can be detected and any error conditions
identified. The command set required to control the memory is consistent with JEDEC
standards.
The Chip Enable, Output Enable and Write Enable signals control the bus operations of the
memory. They allow simple connection to most microprocessors, often without additional
logic.
The device supports Asynchronous Random Read and Page Read from all blocks of the
memory array.
The M29DW128G has one extra 256 words block (extended block, 128 words factory locked
and 128 words customer lockable) that can be accessed using a dedicated command. The
extended block can be protected and so is useful for storing security information. However
the protection is irreversible, once protected the protection cannot be undone.
Each block can be erased independently, so it is possible to preserve valid data while old
data is erased.
The device features different levels of hardware and software block protection to avoid
unwanted program or erase (modify):
● Hardware protection:
– The VPP/WP provides a hardware protection of the four outermost parameter
blocks (two at the top and two at the bottom of the address space).
● Software protection
– Standard protection
– Password protection
● Additional protection features are available upon customer request.
The memory is offered in TSOP56 (14 x 20 mm) and TBGA64 (10 x 13 mm, 1 mm pitch)
packages.
In order to meet environmental requirements, Numonyx offers the M29DW128G in
ECOPACK® packages. ECOPACK packages are Lead-free. The category of second Level
Interconnect is marked on the package and on the inner box label, in compliance with
JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also
marked on the inner box label. The memory is supplied with all the bits erased (set to ’1’).
5/11
5 Page M29DW128G
www.DataSheet4U.com
Please Read Carefully:
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH NUMONYX™ PRODUCTS. NO LICENSE, EXPRESS OR
IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT
AS PROVIDED IN NUMONYX'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NUMONYX ASSUMES NO LIABILITY
WHATSOEVER, AND NUMONYX DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF
NUMONYX PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE,
MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
Numonyx products are not intended for use in medical, life saving, life sustaining, critical control or safety systems, or in nuclear facility
applications.
Numonyx may make changes to specifications and product descriptions at any time, without notice.
Numonyx, B.V. may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights that relate to the
presented subject matter. The furnishing of documents and other materials and information does not provide any license, express or implied,
by estoppel or otherwise, to any such patents, trademarks, copyrights, or other intellectual property rights.
Designers must not rely on the absence or characteristics of any features or instructions marked “reserved” or “undefined.” Numonyx reserves
these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them.
Contact your local Numonyx sales office or your distributor to obtain the latest specifications and before placing your product order.
Copies of documents which have an order number and are referenced in this document, or other Numonyx literature may be obtained by
visiting Numonyx's website at http://www.numonyx.com.
Numonyx StrataFlash is a trademark or registered trademark of Numonyx or its subsidiaries in the United States and other countries.
*Other names and brands may be claimed as the property of others.
Copyright © 11/5/7, Numonyx, B.V., All Rights Reserved.
11/11
11 Page |
Páginas | Total 11 Páginas | |
PDF Descargar | [ Datasheet M29DW128G.PDF ] |
Número de pieza | Descripción | Fabricantes |
M29DW128F | Flash memory | ST Microelectronics |
M29DW128F | Flash memory | Numonyx |
M29DW128G | Flash memory | Numonyx |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |