DataSheet.es    

PDF 200WNA1 Datasheet ( Hoja de datos )

Número de pieza 200WNA1
Descripción PQ200WNA1ZPH
Fabricantes Sharp 
Logotipo Sharp Logotipo



Total 5 Páginas
		
200WNA1 Hoja de datos, Descripción, Manual
PQ200WNA1ZPH
PQ200WNA1ZPH
Compact Surface Mount type
Low Power-Loss Voltage Regulators
Features
1.Output current : 1A
2.High isolation voltage VIN:MAX.24 V
3.Low dissipation current
www.DataShee(tD4Uis.sciopmation current at no load: MAX. 8mA
Output OFF-state dissipation current: MAX.5μA)
4.Built-in ON/OFF function
5.Built-in overcurrent and overheat protection functions
6.Built-in ASO protection function
7.Ceramic capacitor compatible
8.RoHS directive compliant
Applications
1.AV equipment
2.OA equipment
Absolute Maximum Ratings
(Ta=25°C)
Parameter
Symbol
*1 Input voltage
VIN
*1Output control voltage
VC
*1Output adjustment pin voltage Vadj
Output current
IO
*2 Power dissipation
PD
*3 Junction temperature
Tj
Rating
24
24
5
1
8
150
Unit
V
V
V
A
W
°C
Operating temperature Topr -40 to +85 °C
Storage temperature
Tstg -40 to +150 °C
Soldering temperature Tsol
260(10s) °C
*1 All are open except GND and applicable terminals.
*2 PD: With infinite heat sink
*3 There is case that over heat protection function operates at the temperature
Tj:125°C to 150°C,this item cannot be used in this temperature range.
Outline Dimensions
(Unit : mm)
6.6MAX.
5.2±0.5
200WNA1
3
Epoxy resin
Lead finish
identification mark
2.1±0.5
(0.3)
H
(00.25)
0.3
+0.2
-0.1
4-(1.27)
(0.3)
12
45
( ) : Typical dimensions
Product mass:(0.2g)
13
Specific IC
24
5
1 DC input (VIN)
2 ON/OFF control terminal (VC)
3 DC output(VO)
4 Output voltage adjustment(Vadj)
5 GND
Lead finish:Lead-free solder plating
(Composition: Sn2Cu)
Notice The content of data sheet is subject to change without prior notice.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
1 Sheet No.: OP06073

1 page

200WNA1 pdf
PQ200WNA1ZPH
Fig.13 Dropout Voltage vs. Ambient
Temperature
Cu area 740mm2
2.0
1.5
1.0
www.DataSheet4U.com0.5
Cu area 180mm2
Cu area 100mm2
Cu area 70mm2
Cu area 36mm2
0
-40 -20 0 20 40 60 80 100 120
Ambient temperature Ta (°C)
Mounting PCB
PCB
Cu
Material
: Glass-cloth epoxy resin
Size
: 50×50×1.6mm
Cu thickness : 35μm
Fig.14 Output Voltage Adjustment
Characteristics (Typical Value)
20
R1=2kΩ
18
16
14
12
10
8
6
4
2
0
100
1000
10000
100000
R2 (Ω)
Setting of Output Voltage
Output voltage is able to set (3V to 20V) when resistors R1, R2 are attached to ,,terminals. As for the external
resistors to set output voltage, refer to the following figure and Fig.14.
3
4
+
5
Vref
VO
R2
R1 VO=Vref × (1+R2/R1)
[R1=2kΩ, Vref2.65V]
Sheet No.: OP06073
5

5 Page



PáginasTotal 5 Páginas
PDF Descargar[ 200WNA1.PDF ]

Enlace url


Hoja de datos destacado

Número de piezaDescripciónFabricantes
200WNA1PQ200WNA1ZPHSharp
Sharp

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


www.DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar