DataSheet.es    


PDF C10151 Data sheet ( Hoja de datos )

Número de pieza C10151
Descripción (C10150 / C10151) CCD multichannel detector head Designed
Fabricantes Hamamatsu Corporation 
Logotipo Hamamatsu Corporation Logotipo



Hay una vista previa y un enlace de descarga de C10151 (archivo pdf) en la parte inferior de esta página.


Total 7 Páginas

No Preview Available ! C10151 Hoja de datos, Descripción, Manual

IMAGE SENSOR
CCD multichannel detector head
C10150, C10151
Designed for back-thinned CCD area image sensor
C10150 and C10151 are high sensitivity multichannel detector heads for use with back-thinned FFT-CCD area image sensors (S10140/S10141
series) that offer high UV sensitivity and quantum efficiency. C10150 is designed for the non-cooled back-thinned CCD image sensor (S10140
series), while C10151 for the one-stage TE-cooled CCD area image sensors (S10141 series) for detection at even lower light levels. Both C10150
and C10151 incorporate a low-noise driver/amplifier circuit that provides reliable operation from simple external signals. C10151 also includes a
highly stable temperature controller that cools the sensor to a preset temperature level (Ts= -10 ˚C) as soon as the power is turned on. If the
www.DataSheceoto4lUer.cfoamils and causes internal circuitry to overheat, the built-in protection circuit automatically turns off the power to the thermoelectric cooler.
Despite its compact size, the housing configuration is designed for good heat dissipation, and threaded mounting holes on the front panel allow
connections to other devices such as monochrometers. The table below shows back-thinned CCD image sensors for C10150 and C10151.
C10150 and C10151 do not come with a CCD image sensor, so select the desired sensor and order it separately.
Controller for multichannel detector head C7557 is also available. The software supplied with the C7557 allows easy control of the multichannel
detector head and data acquisition.
Features
l Designed for back-thinned CCD area image sensor *1
C10150: for non-cooled type (S10140 series)
C10151: for TE-cooled type (S10141 series)
l Line binning operation *2/area scanning operation
l Driver/amplifier circuit for low noise CCD operation
l Highly stable temperature controller (C10151)
Cooling temperature: -10 ± 0.05 ˚C
l Simple signal input operation
l Compact configuration
Applications
l Fluorescence spectroscopy
l Raman spectroscopy
l Other low-light-level detection
s Selection guide
The table below shows CCD area image sensors applicable for C10150, C10151.
Since C10150, C10151 do not include a CCD area image sensor, so select the desired sensor and order it separately.
CCD area image sensor
Type No.
Type No.
Number of pixels Number of active pixels
Active area
[mm (H) × mm (V)]
S10140-1007
1044 × 128
1024 × 122
12.288 × 1.464
S10140-1008
1044 × 256
1024 × 250
12.288 × 3.000
C10150
S10140-1009
S10140-1107
1044 × 512
2068 × 128
1024 × 506
2048 × 122
12.288 × 6.072
24.576 × 1.464
S10140-1108
2068 × 256
2048 × 250
24.576 × 3.000
S10140-1109
2068 × 512
2048 × 506
24.576 × 6.072
S10141-1007
1044 × 128
1024 × 122
12.288 × 1.464
S10141-1008
1044 × 256
1024 × 250
12.288 × 3.000
C10151
S10141-1009
S10141-1107
1044 × 512
2068 × 128
1024 × 506
2048 × 122
12.288 × 6.072
24.576 × 1.464
S10141-1108
2068 × 256
2048 × 250
24.576 × 3.000
S10141-1109
2068 × 512
2048 × 506
24.576 × 6.072
*1: In normal CCD image sensors that receive light from the front surface, the active area is covered with electrodes for charge transfer.
These electrodes cut off UV radiation incident on the image sensor and also reduce the quantum efficiency. In contrast, back-
thinned CCD image sensors have a unique structure in which the back of the active area is finely ground to allow light to enter from
the back surface. This structure ensures high UV sensitivity and quantum efficiency because incident light need not pass through the
electrodes.
*2: The FFT-CCD was originally designed as a two-dimensional image sensor. However, it can be operated like a linear image sensor
having a large active area by transferring all the pixel signals in the vertical direction to the horizontal register (this is referred to as
line binning).
1

1 page




C10151 pdf
CCD multichannel detector head C10150, C10151
s Pin connection of "SIGNAL I/O" connector
15-pin D-sub connector
8 7 6 5 4 3 21
15 14 13 12 11 10 9
Pin No.
1
www.DataSheet4U.com
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Terminal name
Mode select
Data video
VA1+ (+15 V)
VA1- (-15 V)
VD1 (+5 V)
Start
CLK
EOS
A. GND
A. GND
VA2 (+24 V)
D. GND
D. GND
D. GND
Trigger
KACCC0069EA
Description
Digital input signal used to select between the line binning operation and area scanning
operation.
HCMOS compatible.
High level or left open: line binning operation
Low level: area scanning operation
Analog video output. Positive polarity
Analog power supply
Analog power supply
Digital power supply
Digital input signal for initializing the circuit.
HCMOS compatible. Positive logic.
The interval of the Start pulses determines the integration time of the CCD image sensor.
Digital input signal for operating the circuit.
HCMOS compatible. Rising edge operation.
Digital output signal for indicating end-of-scan of the image sensor.
HCMOS compatible. Negative logic.
Analog ground
Analog ground
Analog power supply
Digital ground
Digital ground
Digital ground
Digital output signal for A/D conversion. HCMOS compatible. Positive logic.
s Pin connection of "TE CONTROL I/O" connector (C10151)
9-pin D-sub connector
5 4 3 21
9 8 76
KACCC0075EA
Pin No. Terminal name
Description
1 VD2 (+5 V) Digital power supply
2 Temp monitor Analog output signal of the temperature of the CCD image sensor
Digital input signal for starting to cool down. HCMOS compatible.
3 Cooling control High level or left open: cooling
Low level: stand-by
4
Vp (+5 V)
Power supply for the thermoelectric cooler in the CCD image sensor.
(Please use AWG 18 wire)
5 VF (+12 V) Power supply for cooling fan
6
D. GND
Ground
7
D. GND
Ground
8
P. GND
Power supply return of the thermoelectric cooler mounted in the CCD image sensor.
(Please use AWG 18 wire)
9
F. GND
Power supply return for cooling fan
Available for using same power supply (+5 V) for "+VD2" and "+Vp".
Caution) Do not connect "VD2" and "Vp" together on the backside of the 9-pin D-sub connector.
These may be connected (shorted) at the power supply end, not 9-pin D-sub connector.
5

5 Page










PáginasTotal 7 Páginas
PDF Descargar[ Datasheet C10151.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
C10150(C10150 / C10151) CCD multichannel detector head DesignedHamamatsu Corporation
Hamamatsu Corporation
C10151(C10150 / C10151) CCD multichannel detector head DesignedHamamatsu Corporation
Hamamatsu Corporation
C1015J5003AHFHybrid CouplerAnaren Microwave
Anaren Microwave

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar