DataSheet.es    


PDF 24C02 Data sheet ( Hoja de datos )

Número de pieza 24C02
Descripción (24C0x) 8-lead SOP and 8-lead TSSOP Packages
Fabricantes Estek Electronics 
Logotipo Estek Electronics Logotipo



Hay una vista previa y un enlace de descarga de 24C02 (archivo pdf) en la parte inferior de esta página.


Total 13 Páginas

No Preview Available ! 24C02 Hoja de datos, Descripción, Manual

24C02 / 24C04 / 24C08 / 24C16
Features
¡Wide Voltage Operation
- VCC = 1.8V to 5.5V
¡Operating Ambient Temperature: -40 C to +85 C
¡Internally Organized:
- 24C02, 256 X 8 (2K bits)
www.DataShee-t4U24.cCo0m4, 512 X 8 (4K bits)
- 24C08, 1024 X 8 (8K bits)
- 24C16, 2048 X 8 (16K bits)
¡Two-wire Serial Interface
¡Schmitt Trigger, Filtered Inputs for Noise Suppression
¡Bidirectional Data Transfer Protocol
¡1 MHz (5V), 400 kHz (1.8V, 2.5V, 2.7V) Compatibility
¡Write Protect Pin for Hardware Data Protection
¡8-byte Page (2K), 16-byte Page (4K, 8K, 16K) Write Modes
¡Partial Page Writes Allowed
¡Self-timed Write Cycle (5 ms max)
¡High-reliability
- Endurance: 1 Million Write Cycles
- Data Retention: 100 Years
¡8-lead PDIP, 8-lead SOP and 8-lead TSSOP Packages
¡Die Sales: Wafer Form, Waffle Pack
General Description
The 24C02/ 24C04/ 24C08/ 24C16 provides 2048/4096/8192/16384 bits of serial electrically erasable and
programmable read-only memory (EEPROM) organized as 256/512/1024/2048 words of 8 bits each. The device is
optimized for use in many industrial and commercial applications where low-power and low-voltage operation are
essential. The 24C02/ 24C04/ 24C08/ 24C16 is available in space-saving 8-lead PDIP, 8-lead SOP, and 8-lead
TSSOP packages and is accessed via a two-wire serial interface.
Pin Configuration
8-lead PDIP
C16 / C08 / C04 / C02
NC / NC / NC / A0
NC / NC / A1 / A1
NC / A2 / A2 / A2
GND
1
2
3
4
8 VCC
7 WP
6 SCL
5 SDA
8-lead SOP
C16 / C08 / C04 / C02
NC / NC / NC / A0
NC / NC / A1 / A1
NC / A2 / A2 / A2
GND
1
2
3
4
8 VCC
7 WP
6 SCL
5 SDA
8-lead TSSOP
C16 / C08 / C04 / C02
NC / NC / NC / A0
NC / NC / A1 / A1
NC / A2 / A2 / A2
GND
1
2
3
4
8 VCC
7 WP
6 SCL
5 SDA
Pin Descriptions
¡Table 1: Pin Configuration
Pin Designation
A0 - A2
SDA
SCL
WP
GND
VCC
NC
Type
I
I/O & Open-drain
I
I
P
P
NC
Name and Functions
Address Inputs
Serial Data
Serial Clock Input
Write Protect
Ground
Power Supply
No Connect
BEIJING ESTEK ELECTRONICS CO.,LTD
1

1 page




24C02 pdf
¡Figure 3: Output Acknowledge
24C02 / 24C04 / 24C08 / 24C16
SCL
www.DataSheet4U.comDATA IN
DATA OUT
START
1
89
ACKNOWLEDGE
Device Addressing
The 2K, 4K, 8K and 16K EEPROM devices all require an 8-bit device address word following a start condition to enable
the chip for a read or write operation (see to Figure 4 on page 7).
The device address word consists of a mandatory "1", "0" sequence for the first four most significant bits as shown.
This is common to all the Serial EEPROM devices.
The next 3 bits are the A2, A1 and A0 device address bits for the 2K EEPROM. These 3 bits must compare to their
corresponding hardwired input pins.
The 4K EEPROM only uses the A2 and A1 device address bits with the third bit being a memory page address bit. The
two device address bits must compare to their corresponding hardwired input pins. The A0 pin is no connect.
The 8K EEPROM only uses the A2 device address bit with the next 2 bits being for memory page addressing. The A2 bit
must compare to its corresponding hard-wired input pin. The A1 and A0 pins are no connect.
The 16K does not use any device address bits but instead the 3 bits are used for memory page addressing. These page
addressing bits on the 4K, 8K and 16K devices should be considered the most significant bits of the data word address
which follows. The A0, A1 and A2 pins are no connect.
The eighth bit of the device address is the read/write operation select bit. A read operation is initiated if this bit is high
and a write operation is initiated if this bit is low.
Upon a compare of the device address, the EEPROM will output a "0". If a compare is not made, the chip will return to a
standby state.
BEIJING ESTEK ELECTRONICS CO.,LTD
5

5 Page





24C02 arduino
24C02 / 24C04 / 24C08 / 24C16
Bus Timing
¡Figure 10: SCL: Serial Clock, SDA: Serial Data I/O
www.DataSheet4U.ScCoLm
tSU.STA
SDA_IN
SDA_OUT
tF
tLOW
tHD.STA
tHIGH
tLOW
tHD.DAT
tSU.DAT
tAA tDH
tR
tSU.STO
tBUF
Write Cycle Timing
¡Figure 11: SCL: Serial Clock, SDA: Serial Data I/O
SCL
SDA
8th BIT
ACK
STOP
CONDITION
tWR(1)
START
CONDITION
Note
1. The write cycle time tWR is the time from a valid stop condition
of a write sequence to the end of the internal clear/write cycle.
BEIJING ESTEK ELECTRONICS CO.,LTD
11

11 Page







PáginasTotal 13 Páginas
PDF Descargar[ Datasheet 24C02.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
24C00128-Bit I2C Bus Serial EEPROMMicrochipTechnology
MicrochipTechnology
24C011K/2K/4K 5.0V I2C Serial EEPROMsMicrochipTechnology
MicrochipTechnology
24C012-WireSerialEEPROMATMELCorporation
ATMELCorporation
24C01(24C01 - 24C16) 2-WIRE SERIAL CMOS EEPROMISSI
ISSI

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar