DataSheet.es    

PDF OB2262 Datasheet ( Hoja de datos )

Número de pieza OB2262
Descripción Current Mode PWM Controller
Fabricantes On-Bright 
Logotipo On-Bright Logotipo

Total 13 Páginas
		
OB2262 Hoja de datos, Descripción, Manual
OB2262
GENERAL DESCRIPTION
OB2262 is a highly integrated current mode PWM
control IC optimized for high performance, low
standby power and cost effective offline flyback
converter applications in sub 30W range.
PWM switching frequency at normal operation is
externally programmable and trimmed to tight range.
At no load or light load condition, the IC operates in
extended ‘burst mode’ to minimize switching loss.
Lower standby power and higher conversion
efficiency is thus achieved.
www.DataSheeVt4DUD.comlow startup current and low operating current
contribute to a reliable power on startup design with
OB2262. A large value resistor could thus be used in
the startup circuit to minimize the standby power.
The internal slope compensation improves system
large signal stability and reduces the possible sub-
harmonic oscillation at high PWM duty cycle output.
Leading-edge blanking on current sense(CS) input
removes the signal glitch due to snubber circuit diode
reverse recovery and thus greatly reduces the external
component count and system cost in the design.
OB2262 offers complete protection coverage with
automatic self-recovery feature including Cycle-by-
Cycle current limiting (OCP), over load protection
(OLP), VDD over voltage clamp and under voltage
lockout (UVLO). The Gate-drive output is clamped
to maximum 18V to protect the power MOSFET.
Excellent EMI performance is achieved soft
switching control at the totem pole gate drive output.
TYPICAL APPLICATION
Current Mode PWM Controller
The tone energy at below 20KHZ is minimized in the
design and audio noise is eliminated during operation.
OB2262 is offered in SOT23-6, SOP-8 and DIP-8
packages.
FEATURES
Extended Burst Mode Control For Improved
Efficiency and Minimum Standby Power Design
Audio Noise Free Operation
External Programmable PWM Switching
Frequency
Internal Synchronized Slope Compensation
Low VDD Startup Current and Low Operating
Current (1.4mA)
Leading Edge Blanking on Current Sense Input
Good Protection Coverage With Auto Self-
Recovery
o VDD Over Voltage Clamp and Under Voltage
Lockout with Hysteresis (UVLO)
o Gate Output Maximum Voltage Clamp (18V)
o On-Bright Proprietary Line Input Compensated
Cycle-by-Cycle Over-current Threshold Setting
For Constant Output Power Limiting Over
Universal Input Voltage Range.
o Overload Protection (OLP).
APPLICATIONS
Offline AC/DC flyback converter for
Battery Charger
Power Adaptor
Set-Top Box Power Supplies
Open-frame SMPS
AC IN
EMI
F i l te r
4
2
+
+
V DD
GATE
OB2262
RI SENSE
FB GND
+ DC OUT
OB431
©On-Bright Electronics
Confidential to Micro Bridge
- 1 - OB_DOC_DS_62B5

1 page

OB2262 pdf
OB2262
Current Mode PWM Controller
ELECTRICAL CHARACTERISTICS
(TA = 25OC if not otherwise noted)
Symbol
Parameter
Test Conditions
Min Typ Max Unit
Supply Voltage (VDD)
I_VDD_Stup VDD Start up Current VDD =12.5V, RI=100K
3 20 uA
Measure Leakage current
into VDD
I_VDD_Ops Operation Current
VDD=16V,
1.4 mA
UVLO(ON)
VDD Under Voltage
RI=100Kohm, VFB=3V
7.8 8.8 9.8 V
Lockout Enter
www.DataSheetU4UV.cLoOm(OFF) VDD Under Voltage
13 14 15 V
Lockout Exit
(Recovery)
VDD_Clamp
VDD Zener Clamp
Voltage
IVDD = 5 mA
34 V
Feedback Input Section(FB Pin)
AVCS
PWM Input Gain
VFB_Open
VFB Open Loop Voltage
IFB_Short
FB pin short circuit
current
VTH_0D
Zero Duty Cycle FB
Threshold Voltage
VTH_PL
Power Limiting FB
Threshold Voltage
TD_PL
Power limiting
Debounce Time
ZFB_IN
Input Impedance
DC_MAX
Maximum Duty Cycle
ΔVFB /ΔVcs
Short FB pin to GND and
measure current
VDD = 16V,
RI=100Kohm
VDD=18V,
RI=100Kohm, FB=3V,
CS=0
2.0 V/V
4.8 V
1.2 mA
0.75 V
3.7 V
35 mSec
6 Kohm
75 %
Current Sense Input(Sense Pin)
T_blanking
Leading edge blanking RI = 100 Kohm
300 ns
time
ZSENSE_IN
TD_OC
Input Impedance
Over Current Detection VDD = 16V,
and Control Delay
CS>VTH_OC, FB=3.3V
40
75
Kohm
nSec
VTH_OC
Over-Current
Threshold Voltage or
FB=3.3V, RI=100 Kohm 0.70 0.75 0.80 V
Equivalent maximum
input voltage at SENSE
Oscillator
FOSC
f_Temp
f_VDD
RI_range
V_RI_open
Fosc_BM
Normal Oscillation
Frequency
Frequency Temperature
Stability
Frequency Voltage
Stability
Operating RI Range
RI open load voltage
Burst Mode Base
Frequency
RI = 100 Kohm
VDD = 16V,
RI=100Kohm, TA -20oC
to 100 oC
VDD = 12-25V,
RI=100Kohm
VDD = 16V, RI =
100Kohm
60
50
65 70 KHZ
5%
5%
100 150 Kohm
2V
22 KHZ
©On-Bright Electronics
Confidential to Micro Bridge
- 5 - OB_DOC_DS_62B5

5 Page

OB2262 arduino
PACKAGE MECHANICAL DATA
SOT23-6
OB2262
Current Mode PWM Controller
www.DataSheet4U.com
©On-Bright Electronics
- 11 -
Confidential to Micro Bridge
OB_DOC_DS_62B5

11 Page


PáginasTotal 13 Páginas
PDF Descargar[ OB2262.PDF ]

Enlace url


Hoja de datos destacado

Número de piezaDescripciónFabricantes
OB2262Current Mode PWM ControllerOn-Bright
On-Bright
OB226215W Adapter Module DesignOn-Bright
On-Bright
OB2263Current Mode PWM ControllerOn-Bright
On-Bright
OB2268(OB2268 / OB2269) Current Mode PWM ControllerLiteon
Liteon

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


www.DataSheet.es    |   2018   |  Privacy Policy  |  Contacto  |  Buscar