|
|
PDF LM2402 Data sheet ( Hoja de datos )
| Número de pieza | LM2402 | |
| Descripción | Monolithic Triple 3 ns CRT Driver | |
| Fabricantes | National Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LM2402 (archivo pdf) en la parte inferior de esta página. Total 11 Páginas | ||
|
No Preview Available !
August 1999
LM2402
Monolithic Triple 3 ns CRT Driver
General Description
The LM2402 is an integrated high voltage CRT driver circuit
designed for use in high resolution color monitor applica-
tions. The IC contains three high input impedance, wide
band amplifiers which directly drive the RGB cathodes of a
CRT. Each channel has its gain internally set to −14 and can
drive CRT capacitive loads as well as resistive loads pre-
sented by other applications, limited only by the package’s
power dissipation.
The IC is packaged in an industry standard 11 lead TO-220
molded plastic power package. See thermal considerations
on page 5.
Features
n Rise/fall times typically 3.0/2.8 ns with 8 pF load at
40 VPP
n Well matched with LM2202 video preamps
n Output swing capability: 50 VPP for VCC = 80V
n 1V to 5V input range
n Stable with 0-20 pF capacitive loads and inductive
peaking networks
n Convenient TO-220 staggered lead package style
n Standard LM240X family pinout which is designed for
easy PCB layout
Applications
n CRT driver for color monitors with display resolutions up
to 1600 x 1200
n Pixel clock frequency up to 200 MHz
Schematic and Connection Diagrams
DS101016-1
FIGURE 1. Simplified Schematic Diagram
(One Channel)
Top View
Order Number LM2402T
DS101016-2
© 1999 National Semiconductor Corporation DS101016
www.national.com
1 page  
Application Hints (Continued)
mance of the device in the NSC application board. The val-
ues shown in Figure 9 can be used as a good starting point
for the evaluation of the LM2402.
Effect of Load Capacitance
The output rise and fall times as well as overshoot will vary
as the load capacitance varies. The values of the output cir-
cuit (R1, R2 and L1 in Figure 9) should be chosen based on
the nominal load capacitance. Once this is done the perfor-
mance of the design can be checked by varying the load
based on what the expected variation will be during produc-
tion.
Effect of Offset
Figure 7 shows the variation in rise and fall times when the
output offset of the device is varied from 40 to 50 VDC. The
rise and fall times show about the same overall variation.
The slightly faster fall time is fastest near the center point of
45V, making this the optimum operating point since there is
little increase in the rise time.
THERMAL CONSIDERATIONS
Figure 4 shows the performance of the LM2402 in the test
circuit shown in Figure 2 as a function of case temperature.
Figure 4 shows that both the rise and fall times of the
LM2402 become slightly slower as the case temperature in-
creases from 40˚C to 125˚C. In addition to exceeding the
safe operating temperature, the rise and fall times will typi-
cally exceed 3 nsec. Please note that the LM2402 is never
to be operated over a case temperature of 100˚C.
Figure 6 shows the total power dissipation of the LM2402 vs.
Frequency when all three channels of the device are driving
both an 8 pF load and a 20 pF load. This graph gives the de-
signer the information needed to determine the heat sink re-
quirement for his application. The designer should note that
if the load capacitance is increased the AC component of the
total power dissipation will also increase as shown in Figure
6. The designer should also remember that the actual video
signal has a period of around 70% to 75%. The remainder of
the time the video signal is inactive, or at the black level (be-
low the black level if blanked). During this time the LM2402
will be at the black level, or below, dissipating under 4W. Re-
ferring to Figure 14 and using an input black level voltage of
1.9V, the power dissipation during the inactive video time is
3.8W, including both the 80V and 12V supplies.
The LM2402 case temperature must be maintained below
100˚C. Assume the worst case operating condition is a
100 MHz square wave during active video (a pixel clock of
200 MHz with one pixel on, one pixel off). From Figure 6 one
can see that the power dissipation of the LM2402 is 28W if
the 100 MHz square wave is applied all the time. One must
also compensate for the inactive period of video. From Fig-
ure 14 it has been calculated that the power dissipation dur-
ing the inactive video is 4W. Therefore there is an additional
24W of power dissipation due to the AC signal. Assume that
the AC signal is active 72% of the time. Now the AC power
dissipation is:
24W x 0.72 = 17W
The total power dissipation for 72% active video time is:
17W + 4W = 21W
If the maximum expected ambient temperature is 50˚C and
using the maximum power dissipation of 21W (video being
active only 72% of the frame), then a maximum heat sink
thermal resistance can be calculated:
This example assumes a capacitive load of 8 pF and no re-
sistive load.
TYPICAL APPLICATION
A typical application of the LM2402 is shown in Figure 10.
Used in conjunction with three LM2202s, a complete video
channel from monitor input to CRT cathode can be achieved.
Performance is excellent for resolutions up to 1600 x 1200
and pixel clock frequencies at 200 MHz. Figure 10 is the
schematic for the NSC demonstration board that can be
used to evaluate the LM2202/2402 combination in a monitor.
PC Board Layout Considerations
For optimum performance, an adequate ground plane, isola-
tion between channels, good supply bypassing and minimiz-
ing unwanted feedback are necessary. Also, the length of the
signal traces from the preamplifier to the LM2402 and from
the LM2402 to the CRT cathode should be as short as pos-
sible. The red video trace from the buffer transistor to the
LM2402 input is about the absolute maximum length one
should consider on a PCB layout. If possible the traces
should actually be shorter than the red video trace. The fol-
lowing references are recommended for video board design-
ers:
Ott, Henry W., “Noise Reduction Techniques in Electronic
Systems”, John Wiley & Sons, New York, 1976.
“Guide to CRT Video Design”, National Semiconductor Appli-
cation Note 861.
“Video Amplifier Design for Computer Monitors”, National
Semiconductor Application Note 1013.
Pease, Robert A., “Troubleshooting Analog Circuits”,
Butterworth-Heinemann, 1991.
Because of its high small signal bandwidth, the part may os-
cillate in a monitor if feedback occurs around the video chan-
nel through the chassis wiring. To prevent this, leads to the
video amplifier input circuit should be shielded, and input cir-
cuit wiring should be spaced as far as possible from output
circuit wiring.
NSC Demonstration Board
Figures 11, 12 show routing and component placement on
the NSC LM2202/2402 demonstration board. The schematic
of the board is shown in Figure 10. This board provides a
good example of a layout that can be used as a guide for fu-
ture layouts. Note the location of the following components:
• C47 - VCC bypass capacitor, located very close to pin 6
and ground pins. (Figure 12)
• C49 - VBB bypass capacitor, located close to pin 10 and
ground. (Figure 12)
• C46 and C77 - VCC bypass capacitors, near LM2402 and
VCC clamp diodes. Very important for arc protection. (Fig-
ure 11)
The routing of the LM2402 outputs to the CRT is very critical
to achieving optimum performance. Figure 13 shows the
routing and component placement from pin 1 to the blue
cathode. Note that the components are placed so that they
almost line up from the output pin of the LM2402 to the blue
5 www.national.com
5 Page 
Physical Dimensions inches (millimeters) unless otherwise noted
11 Lead Molded TO-220
NS Package Number TA11B
Order Number LM2402T
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: [email protected]
www.national.com
National Semiconductor
Europe
Fax: +49 (0) 1 80-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 1 80-530 85 85
English Tel: +49 (0) 1 80-532 78 32
Français Tel: +49 (0) 1 80-532 93 58
Italiano Tel: +49 (0) 1 80-534 16 80
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: [email protected]
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
11 Page | ||
| Páginas | Total 11 Páginas | |
| PDF Descargar | [ Datasheet LM2402.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LM24010J | Display Module |  Sharp |
| LM24010Z | LCD Dot Matrix Unit | Sharp |
| LM240128NCC | LCD Module |  Shenzhen |
| LM240128NCC-1 | LCD Module | Shenzhen |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |