|
|
PDF SAK82C900 Data sheet ( Hoja de datos )
| Número de pieza | SAK82C900 | |
| Descripción | 82C900 | |
| Fabricantes | Infineon Technologies | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SAK82C900 (archivo pdf) en la parte inferior de esta página. Total 29 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
Data Sheet, V 1.0D3, Mar. 2001
82C900
Standalone TwinCAN Controller
Microcontrollers
Never stop thinking.
1 page  
www.DataSheet4U.com
Preliminary
Standalone TwinCAN Controller
82C900
82C900
Architectural Overview
The Standalone TwinCAN device provides several submodules to control the data flow
and to configure the peripheral function:
Features:
• Two interface channels are implemented for the communication with a host device:
– the Multiplexed Data/Address Bus can be used by an external CPU to read and
write the TwinCAN’s internal registers for initial configuration and control during
normal operation. The standard Infineon Bus Mode and the Motorola Bus Mode can
be handled.
– alternatively, a Synchronous Serial Channel (SSC) may be selected to read out the
initial TwinCAN’s register configuration from a serial EEPROM. The SSC can be
also used by an external control device (microcontroller, CPU, etc.) in order to
exchange control and status information.
• Both communication channels are based on byte transfers. In order to minimize the
communication overhead, all internal 16 bit and 32 bit wide registers can be accessed
in Page Mode requiring only one address byte.
• Powerful initialization mechanism for all registers, the device can be configured via
EEPROM, based on CAN messages or by an external host device.
• Additional input/output functionality controlled by CAN messages. The transmission of
CAN messages can be triggered by input pins if the SSC is used for communication.
• The clock control unit can be supplied with an external clock. Alternatively, an on-chip
oscillator may be used to generate a clock driving also an external device via an output
pin.
• Power Saving features have been implemented. A Sleep Mode and a Power-Down
Mode can be activated in order to minimize the power consumption. The clock control
of the device can be controlled by CAN messages.
• The internal power saving status can be monitored at output pins. This allows flexible
and powerful system partitioning.
• The Device Controller unit generates the internal target address by concatenating the
contents of the PAGE register with the address delivered by the appropriate host read/
write access.
• The Interrupt Control unit passes the interrupt requests generated by the TwinCAN
controller to the external host via selectable output pins.
• The Port Control unit can be used to select the required functionality of the port pins
operating as communication channel, CAN node function monitor, interrupt request
line or general purpose I/O. Furthermore, the slew rate of pins configured for output
operation can be adjusted via this module.
Data Sheet
5 V 1.0D3, 2001-03
5 Page 
www.DataSheet4U.com
82C900
Preliminary
Table 1
Symbol
TXDCB
RESET
RDY
CTRL0
CTRL1
CTRL2
Pin Definitions and Functions (cont’d)
Pin I/O 1) Function
Number
27 O Transmitter Output of CAN Node B
TXDCB delivers the output signal of CAN node B. The
signal level has to be adapted to the physical layer of the
CAN bus via a transceiver device.
3 I Reset
A low level on this pin resets the device.
24 O Ready Signal
Output signal indicating that the standalone device is
ready for data transfer.
9 I/O Control 0
MODE0=0: Chip Select CS
Input used as Chip Select for the device.
MODE0=1: Select Slave SLS
MODE1=0: Input used to enable SSC action when
active.
MODE1=1: Output used to select a slave when active.
20 I/O Control 1
MODE0=0: Address Latch Enable or Address
Strobe, ALE or AS
Input used for latching the address from the multiplexed
address/data bus.
MODE0=1: Serial Channel Clock SCLK
Input/output of the SSC clock.
MODE1=0: Clock input
MODE1=1: Clock output
10 I/O Control 2
MODE0=0: Write or Read/Write, WR or R/W
MODE1=0: Input used as write signal WR
MODE1=1: R/W=0: Data transfer direction = write
MODE1=1: R/W=1: Data transfer direction = read
MODE0=1: Master Transmit Slave Receive MTSR
MODE1=0: Serial data input
MODE1=1: Serial data output
Data Sheet
11 V 1.0D3, 2001-03
11 Page | ||
| Páginas | Total 29 Páginas | |
| PDF Descargar | [ Datasheet SAK82C900.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SAK82C900 | 82C900 | Infineon Technologies |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |