DataSheet.es    


PDF XC-EI50 Data sheet ( Hoja de datos )

Número de pieza XC-EI50
Descripción (XC-Exx0CE) CCD B/W Camera Module
Fabricantes Sony 
Logotipo Sony Logotipo



Hay una vista previa y un enlace de descarga de XC-EI50 (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! XC-EI50 Hoja de datos, Descripción, Manual

www.DataSheet4U.com
CCD B/W CAMERA MODULE
XC-ES50/50CE
XC-ES30/30CE
XC-EI50/50CE
XC-EI30/30CE
User’s
Guide
(Ver. 1.0) — English —

1 page




XC-EI50 pdf
www.DataSheet4U.com
MAIN SPECIFICATIONS
XC-E series
Image pickup device
XC-ES50/50CE, XC-EI50/50CE:
1/2-inch interline transfer CCD
XC-ES30/30CE, XC-EI30/30CE:
1/3-inch interline transfer CCD
Number of effective pixels
XC-ES50/EI50, XC-ES30/EI30:
768 (H)x494 (V)
XC-ES50CE/EI50CE, XC-ES30CE/EI30CE:
752 (H)x582 (V)
CCD horizontal driving frequency
XC-ES50/EI50, XC-ES30/EI30:
14.318 MHz
XC-ES50CE/EI50CE, XC-ES30CE/EI30CE:
14.187 MHz
CCD vertical driving frequency
XC-ES50/EI50, XC-ES30/EI30:
15.734 kHz
XC-ES50CE/EI50CE, XC-ES30CE/EI30CE:
15.625 kHz
Signal system
EIA/CCIR
Cell size
XC-ES50/EI50:
8.4 (H)x9.8 (V) µ m
XC-ES50CE/EI50CE: 8.6 (H)x8.3 (V) µ m
XC-ES30/EI30:
6.35 (H)x7.4 (V) µ m
XC-ES30CE/EI30CE: 6.5 (H)x6.25 (V) µ m
Lens mount
C-mount
Flange back
17.526 mm
Synchronization system
Internal/external
(Selected automatically)
External sync input/output
HD/VD (2 to 5 Vp-p)
* Automatically selected according
to the existence of an input signal
when the selection switch on the rear
panel is set to EXT.
Allowable frequency deviation of external synchronization
±1%
(in horizontal synchronous frequency)
Jitter
Within ± 50 nsec
Scanning system 2:1 interlacing
Non-interlacing
(during external sync input)
Horizontal resolution
XC-ES50/EI50, XC-ES30/EI30:
570 TV lines
XC-ES50CE/EI50CE, XC-ES30CE/EI30CE:
560 TV lines
Sensitivity
XC-ES50/50CE: 400 lx F5,6 (γ =ON, MIN Gain,
without IR cut filter)
XC-ES30/30CE: 400 lx F4 (γ =ON, MIN Gain,
without IR cut filter)
XC-EI50/50CE: 400 lx F11 (γ =OFF, MIN Gain,
without IR cut filter)
XC-EI30/30CE: 400 lx F8 (γ =ON, MIN Gain,
without IR cut filter)
S/N ratio
60dB
Minimum illuminance
XC-ES50/50CE, XC-ES30/30CE:
0.3 lx (F1.4 γ =ON, MAX Gain,
without IR cut filter)
XC-EI50/50CE: 0.1 lx (F1.4 γ =ON, MAX Gain,
without IR cut filter)
XC-EI30/30CE: 0.2 lx (F1.4 (γ =ON, MAX Gain,
without IR cut filter)
Gain
AGC/Manual (Can be selected using
the switch on the rear panel.)
Gamma correction ON/OFF (Can be selected
using the switch on the rear
panel.)
Electronic shutter
XC-ES50/EI50, XC-ES30/EI30:
1/100 to 1/10,000 seconds
XC-ES50CE/EI50CE, XC-ES30CE/EI30CE:
1/120 to 1/10,000 seconds
External trigger shutter
XC-ES50/EI50, XC-ES30/EI30:
1/4 to 1/10,000 seconds
XC-ES50CE/EI50CE, XC-ES30CE/EI30CE:
1/4 to 1/8,000 seconds
*Set using the DIP switch on the rear panel, or
variable with the trigger pulse width.
Supply voltage
+12 VDC (+9.0V to 16V)
Power consumption
XC-ES30/30CE, XC-EI30/30CE:
1.4W
XC-ES50/50CE, XC-EI50/50CE:
1.6W
Operating temperature –5 ˚C to +45 ˚C
Storage temperature –20 ˚C to +60 ˚C
Performance assurance temperature
0 ˚C to +30 ˚C
Operating humidity 20 to 80 % (Non-condensing)
Storage humidity
20 to 95 % (Non-condensing)
Vibration resistance 10G (For 20 minutes in the X, Y,
and Z directions at 20 to 200 Hz)
3

5 Page





XC-EI50 arduino
www.DataSheet4U.com
ELECTRONIC SHUTTER
XC-E series
Using trigger pulse width
• Set DIP switches 1 to 4 on the rear panel to 0.
• An arbitrary shutter speed can be obtained by setting the trigger pulse width to the range of 2 µsec to 250
msec.
Switch
1
2
3
4
5
6
7
8
9
0
Mode 1
Mode 2
(Non-reset mode) (Reset mode)
00
00
00
00
Frame: 0 / Field: 1
00
10
11
00
00
Exposure time = Trigger pulse width + 97 µsec (EIA)
120 µsec (CCIR)
Note
: 1. lt is recommended to set DIP switch 5 for field selection.
(The field selection is about two times in sensitivity as high as the frame selection.)
2. After a trigger pulse is input, a new trigger pulse must not be input before the video
signal obtained by the trigger pulse has been output.
1: ON
0: OFF
Specifications of trigger pulse
A
A: 4 to 5.0 V
B: 0 to 1.0 V
T: 2 µs to 1/4 s
T
B
T: 2 µs to 1/4 s, 100 µs to 1/4 s when setting the shutter speed using DIP switch
* Input impedance: 10 kW or more
* The voltage and pulse width used are measured at pin 11 of a 12-pin multi-connector on the rear panel.
9

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet XC-EI50.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
XC-EI50(XC-Exx0CE) CCD B/W Camera ModuleSony
Sony
XC-EI50CE(XC-Exx0CE) CCD B/W Camera ModuleSony
Sony
XC-EI51(XC-Exx1CE) CCD B/W Camera ModuleSony
Sony
XC-EI51CE(XC-Exx1CE) CCD B/W Camera ModuleSony
Sony

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar