|
|
PDF EXB-8205 Data sheet ( Hoja de datos )
| Número de pieza | EXB-8205 | |
| Descripción | (EXB-8205 / EXB-8505) Cartridge Tape Sybsystem | |
| Fabricantes | Exabyte | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de EXB-8205 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
(;% DQG (;% &DUWULGJH 7DSH
6XEV\VWHP
6WDQGDUG DQG DQG H;WHQGHG OHQJWK FRQILJXUDWLRQV
,QVWDOODWLRQ DQG
2SHUDWLRQ
302967-001
1 page  
Welcome
Thank you for selecting the Exabyte® EXB-8205,
EXB-8205XL, EXB-8505, or EXB-8505XL8mm Cartridge Tape
Subsystem (tape drive). These tape drives are high-capacity,
high-performance, and highly reliable storage devices for
PC, workstation, and local area network (LAN) applications.
The “eXtended-Length” (XL) configurations of the tape
drives (EXB-8205XL and EXB-8505XL) provide additional
capacity by supporting the extended-length EXATAPE™
160m XL 8mm Data Cartridge. Information about the 160m
XL data cartridge is provided on page 24.
May 1994 EXB-8205 and EXB-8505 (Standard and XL)
5
5 Page 
Preparing the Tape Drive for the SCSI Bus
The SCSI bus that you attach the tape drive to must be
terminated correctly to ensure proper operation. The devices
that are physically located at each end of the SCSI cable must
have terminators installed. All other devices on the SCSI
cable must not have terminators installed.
If you place the tape drive at the end of the SCSI bus, you
must terminate the tape drive. The procedure you use
depends on whether the tape drive uses a single-ended or a
differential SCSI configuration.
Termination for a Single-Ended tape drive
The single-ended tape drive includes three single in-line
package (SIP) resistor terminators (R-packs) that can be left
in place if the tape drive terminates the SCSI bus.
CAUTION
The R-packs must be removed if the tape drive does
not terminate the SCSI bus or if external SCSI bus
termination will be used. Instructions for removing
the R-packs are provided below.
Optional External Termination
If desired, you can terminate the single-ended tape drive
externally by removing the R-packs from the back of the
tape drive and installing an external terminator. Exabyte
recommends a Methode Electronics, Inc. dataMate
DM103-02-0 single-ended external terminator.
Removing the R-Packs
To remove the R-packs, follow these steps:
1. Locate the three R-packs on the back of the tape
drive, as shown in Figure 3.
2. Using a pair of flat-nose wiring pliers, grasp each
R-pack in the center and pull it straight out. Be
careful not to squeeze the pliers too tightly or you
may break the R-pack.
May 1994 EXB-8205 and EXB-8505 (Standard and XL)
11
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet EXB-8205.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| EXB-8205 | (EXB-8205 / EXB-8505) Cartridge Tape Sybsystem | Exabyte |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |