|
|
PDF LGA775 Data sheet ( Hoja de datos )
| Número de pieza | LGA775 | |
| Descripción | Mounting Kit | |
| Fabricantes | Noctua | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LGA775 (archivo pdf) en la parte inferior de esta página. Total 4 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
Noctua LGA775 Mounting-Kit
Installation Manual
Thank you very much for choosing a Noctua
cooler. This manual will guide you through the
installation process step by step.
Prior to installing the cooler, please consult the compat-
ibility list on our website and verify that the cooler is fully
compatible with your motherboard.
Should you encounter any difficulties, please check the
FAQs on our website and don’t hesitate to contact our
support team at [email protected]. Noctua cannot
be held responsible for any damage or losses caused by
compatibility issues.
Multilingual versions of this manual are available on our
website: www.noctua.at
Required mounting parts (from the LGA775-bag):
1x LGA backplate
NH-U12P-LGA775 | Installation Manual
the backplate’s screw sockets with the mainboard’s screw-
holes.
Caution: The rubber foam square of the LGA backplate
has to face the mainboard. Don’t remove the white protec-
tion film!
Caution: Don’t forget to
put 4 washers between the
mainboard and the mount-
ing bars to avoid damage to
the mainboard.
Choose the alignment of the mounting bars according to the
desired final orientation of the cooler:
Orientation A
Orientation B
Caution: Make sure that the straight sides of the mounting
bars face the socket and the bulgings are pointing outwards.
Step 4:
Applying thermal paste
If there are residual traces of thermal paste or thermal pads on
your CPU, please clean them off first.
Press a small drop (4-5mm diameter) of NT-H1 onto the cen-
tre of the heat-spreader.
2x short mounting bars
2x short silver
springscrews
Required mounting parts (from the common parts bag):
2x standard fastening brackets 2x red, thin washers
Now screw the mounting bars to the backplate using small
screws and washers.
Caution: Applying too much thermal paste will lower the heat
conductivity and cooling performance!
Caution: Peel off the protection film at the bottom side of the
heatsink first!
8x short screws
2x pressure springs
Step 1:
Removing the mainboard
In case you want to use the NH-U12P on an assembled system,
you first have to remove the mainboard from the case as the
cooler has to be screwed together with the backplate on the
back side of the mainboard.
Step 2:
Attaching the backplate
Place the backplate on the back side of the mainboard, aligning
Step 3:
Attaching the fastening brackets to the heatsink
Tightly screw the fastening brackets to the base of the heatsink
using 4 short screws.
Put the heatsink onto the CPU and turn it back and forth a few
times in order to spread the paste.
1 page | ||
| Páginas | Total 4 Páginas | |
| PDF Descargar | [ Datasheet LGA775.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LGA775 | Mounting Kit | Noctua |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |