DataSheet.es    


PDF T359Dxxxxxx Data sheet ( Hoja de datos )

Número de pieza T359Dxxxxxx
Descripción Tantalum Dipped / Radial
Fabricantes Kemet Electronics 
Logotipo Kemet Electronics Logotipo



Hay una vista previa y un enlace de descarga de T359Dxxxxxx (archivo pdf) en la parte inferior de esta página.


Total 13 Páginas

No Preview Available ! T359Dxxxxxx Hoja de datos, Descripción, Manual

www.DataSheet4U.com TANTALUM DIPPED / RADIAL — POLAR
PERFORMANCE CHARACTERISTICS
CAPACITANCE/VOLTAGE RANGE:
T35X/T39X: 0.1-680µF, 3-50 Volts.
T36X: 0.1-330µF, 6-50 Volts.
CAPACITANCE TOLERANCE: Available in stan-
dard EIA nominal values with ±20% and ±10%
standard.
DISSIPATION FACTOR: Maximum DF limits are
shown in corresponding series part number list-
ings. See Application Notes Section, page 76 for
additional information.
DC LEAKAGE CURRENT: Maximum leakage val-
ues at 25° are shown in part number listings,
pages 63-65, 67, 68 and 70. See Application
Notes Section, pages 76 & 77 for additional infor-
mation.
RATED VOLTAGE; WORKING VOLTAGE; SURGE
VOLTAGE; REVERSE VOLTAGE: See Application
Notes Section, pages 76 & 77 for description.
IMPEDANCE and ESR: See Application Notes
Section, page 77 & 78 for description. Reference
ESR values are shown in table below.
Commercial T35X/T36X/T39X ESR (OHMS) at 100 kHz @ +25°C
(The ESR values provided below are for reference only. No warranty, as
stated on page 3 and reincorporated here, is made as to the accuracy
of these values for any particular T35X, T36X, T39X Series product.)
Cap. 6 10 16 20 25 35 50
µF Volt Volt Volt Volt Volt Volt Volt
0.10 26.0 26.0
0.15 21.0 21.0
0.22 17.0 17.0
0.33 15.0 15.0
0.47 13.0 13.0
0.68 10.0 10.0
1.00 10.0 10.0 8.0 8.0
1.50 10.0 9.0 8.0 6.0 5.0
2.20 13.0 8.0 7.0 6.0 5.0 3.5
3.30 13.0 10.0 6.0 5.5 5.0 4.0 3.0
4.70 10.0 8.0 5.0 4.5 4.0 3.0 2.5
6.80 8.0 6.0 4.0 3.6 3.1 2.5 2.0
10.0 6.0 5.0 3.2 2.9 2.5 2.0 1.6
15.0 5.0 3.7 2.5 2.3 2.0 1.6 1.2
22.0 3.7 2.7 2.0 1.8 1.5 1.3 1.0
33.0 3.0 2.1 1.6 1.4 1.2 1.0
47.0 2.0 1.7 1.3 1.2 1.0 0.8
68.0 1.8 1.3 1.0 0.9 0.8
100.0 1.6 1.0 0.8 0.6
150.0 0.9 0.8 0.6
220.0 0.9 0.6
330.0 0.7
AC RIPPLE VOLTAGE: Permissible AC ripple volt-
age is related to equivalent series resistance
(ESR) and power dissipation capability. Maximum
power dissipation for each case size is listed in
Table below. For additional description see page
78.
Case
Size
Power Dissipation
(max.) @ 25°C (watts)
T35X, A
T39X B
C
D
E
F
G
H
J
K
L
M
.040
.050
.060
.065
.070
.080
.090
.100
.110
.120
.130
.140
T36X A
B
C
D
.050
.075
.090
.135
Maximum Power Dissipation Capability @ 25°C
ENVIRONMENTAL CONSIDERATIONS:
A. Shock Test: MIL-STD-202, Method 213.
B. Thermal Shock, MIL-STD-202, Method 107,
Condition A.
C. Moisture Resistance: MIL-STD-202,
Method 106.
D. Solderability: MIL-STD-202, Method 208.
For additional Environmental Test Information
see pages 80, 81 and 82.
LEAD MATERIAL: Effective June 30, 2005 the
T35x, T368 and T39x Series will be available, as an
option, with 100% Matte Tin (RoHS compliant) lead wire
or Sn/Pb lead wire. Please see page 63 for part number
ordering information. The T363 and T369 lead mater-
ial will remain Sn/Pb solder coated steel core with a
copper ply per MIL-STD-127 and at this time will not
be available with a 100% Sn option.
LEAD TAPE AND REEL: Reeling per specification
RS-468. See pages 72 - 74 for additional information.
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606 (864) 963-6300
61

1 page




T359Dxxxxxx pdf
www.DataSheet4U.com TANTALUM DIPPED / RADIAL - POLAR
T350, T351, T352, T353, T354, T355 & T356 SERIES “ULTRADIP II”
T35X
CAPAC-
ITANCE
µF
CASE
SIZE
RATINGS AND PART NUMBER REFERENCE
KEMET PART NUMBER
D.C.
LEAKAGE
µA@25°C
MAX.
DISSI-
PATION
FACTOR
%@25°C,
120Hz
CAPAC-
ITANCE
µF
CASE
SIZE
KEMET PART NUMBER
D.C.
LEAKAGE
µA@25°C
35 VOLT RATING AT 85°C —
23 VOLT RATING AT 125°C
50 VOLT RATING AT 85°C —
33 VOLT RATING AT 125°C
0.10 A T35(1)A104(3)035A(4) 0.5
0.12 A T35(1)A124(3)035A(4) 0.5
0.15 A T35(1)A154(3)035A(4) 0.5
0.18 A T35(1)A184(3)035A(4) 0.5
0.22 A T35(1)A224(3)035A(4) 0.5
0.27 A T35(1)A274(3)035A(4) 0.5
0.33 A T35(1)A334(3)035A(4) 0.5
0.39 A T35(1)A394(3)035A(4) 0.5
0.47 A T35(1)A474(3)035A(4) 0.5
0.56 A T35(1)A564(3)035A(4) 0.5
0.68 A T35(1)A684(3)035A(4) 0.5
0.82 A T35(1)A824(3)035A(4) 0.5
1.0 A T35(1)A105(3)035A(4) 0.5
1.2 B T35(1)B125(3)035A(4) 0.5
1.5 B T35(1)B155(3)035A(4) 0.5
1.8 C T35(1)C185(3)035A(4) 0.5
2.2 C T35(1)C225(3)035A(4) 0.6
2.7 D T35(1)D275(3)035A(4) 0.7
3.3 D T35(1)D335(3)035A(4) 0.9
3.9 E T35(1)E395(3)035A(4) 1.0
4.7 E T35(1)E475(3)035A(4) 1.3
5.6 F T35(1)F565(3)035A(4) 1.6
6.8 F T35(1)F685(3)035A(4) 1.9
8.2
10.0
G T35(1)G825(3)035A(4) 2.3
G T35(1)G106(3)035A(4) 2.8
12.0 J T35(2)J126(3)035A(4) 3.4
15.0 J T35(2)J156(3)035A(4) 4.2
18.0
22.0
K T35(2)K186(3)035A(4) 5.0
K T35(2)K226(3)035A(4) 6.2
27.0 L T35(2)L276(3)035A(4) 7.6
33.0 L T35(2)L336(3)035A(4) 9.2
3
3
3
3
3
3
3
3
3
3
3
3
3
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
0.10 A T35(1)A104(3)050A(4) 0.5
0.12 A T35(1)A124(3)050A(4) 0.5
0.15 A T35(1)A154(3)050A(4) 0.5
0.18 A T35(1)A184(3)050A(4) 0.5
0.22 A T35(1)A224(3)050A(4) 0.5
0.27 A T35(1)A274(3)050A(4) 0.5
0.33 A T35(1)A334(3)050A(4) 0.5
0.39 B T35(1)B394(3)050A(4) 0.5
0.47 B T35(1)B474(3)050A(4) 0.5
0.56 B T35(1)B564(3)050A(4) 0.5
0.68 B T35(1)B684(3)050A(4) 0.5
0.82 B T35(1)B824(3)050A(4) 0.5
1.0 B T35(1)B105(3)050A(4) 0.5
1.2 D T35(1)D125(3)050A(4) 0.5
1.5 E T35(1)E155(3)050A(4) 0.6
1.8 E T35(1)E185(3)050A(4) 0.7
2.2 E T35(1)E225(3)050A(4) 0.9
2.7 F T35(1)F275(3)050A(4) 1.1
3.3 F T35(1)F335(3)050A(4) 1.3
3.9 G T35(1)G395(3)050A(4) 1.6
4.7 G T35(1)G475(3)050A(4) 1.9
5.6 H T35(1)H565(3)050A(4) 2.2
6.8 J T35(2)J685(3)050A(4) 2.7
8.2 J T35(2)J825(3)050A(4) 3.3
10.0 K T35(2)K106(3)050A(4) 4.0
12.0 K T35(2)K126(3)050A(4) 4.8
15.0 L T35(2)L156(3)050A(4) 6.0
18.0 L T35(2)L186(3)050A(4) 7.2
22.0 M T35(2)M226(3)050A(4) 8.8
39.0
47.0
M T35(2)M396(3)035A(4) 10.0
M T35(2)M476(3)035A(4) 10.0
6
6
(1) To complete KEMET Part Number, insert Series Designation as follows: 0= T350, 1= T351, 2= T352, 3= T353, 4= T354, 5= T355, 6= T356.
(2) To complete KEMET Part Number, insert only Series Designation as follows: 0= T350, 3= T353, 4= T354, 6= T356.
(3) To complete KEMET Part Number, insert Capacitance Tolerance Symbol: M= ±20%, K= ±10%.
(4) To complete KEMET Part Number, insert Lead Material Designation as follows: S = Sn/Pb (tin/lead) and T = 100% Tin.
Note: Higher voltage and better capacitance tolerance product may be substituted for an order within the same case size at KEMET's option.
MAX.
DISSI-
PATION
FACTOR
%@25°C,
120Hz
3
3
3
3
3
3
3
3
3
3
3
3
3
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606 (864) 963-6300
65

5 Page





T359Dxxxxxx arduino
www.DataSheet4U.com
PACKAGING INFORMATION
KEMET offers Solid Tantalum Capacitors fully compatible for use with automatic insertion machines for radial-lead components. Aris Reeling meets
all requirements of EIA Standard RS-468. KEMET capacitors are wound on a precision made ARIS Reel Package. ARIS Ammo Package is also available.
Tantalum Dipped Radial – ARIS Specification (Automatic Radial Insertion System)
Tantalum Dipped Tape and Reel Dimensions in Millimeters & (Inches)
Dimension
Body Height (1)
Symbol
Nominal
mm (inch)
A 17.0 (0.67)
Tolerance
mm (inch)
Maximum
Dimension
Nominal
Symbol mm (inch)
Component Pitch (5) P 12.7 (.500)
Tolerance
mm (inch)
± 1.0 (± .039)
Body Width (1)
A1 10.2 (0.40)
Maximum
Sprocket Hole
Pitch (2)
Sprocket Hole
Diameter
D0 4.0 (.157)
± 0.3 (±.012)
Sprocket Hole
Center to Lead
Lead Diameter
d 0.51 or 0.64
± 0.05 (.002)
Center (3) (4)
(.020) (.025)
Sprocket Hole Center
Lead Center (4)
F See Note Below
to Component (5)
Center
Component Base
H
C-7301 C-7303
C-7301
C-7303 Body Thickness
to Tape Center (4)
16.0 (.630) 18.0 (.709) ±0.5 (±.020) Minimum
Lead Standoff
Height
H0 C-7301 C-7303
C-7301
C-7303 Total Tape Thickness
16.0 (.630) 18.0 (.709) ±0.5 (±.020) Minimum Carrier Tape Width
Component Height
Above Tape Center
H1 32.25 (1.270)
Maximum
Hold-Down Tape
Component Alignment Δ H 0
1.0 (.039)
Width
Front to Rear
Sprocket Hole
Cut Out Length
L 11.0 (.433)
Maximum
Location
Hold-Down Tape
Lead Protrustion
L1 1.0 (.039)
Maximum
Location
Notes: (1) See page 62 for T35X and page 69 for T39X specific dimensions.
(2) Cumulative pitch error ± 1.0mm (.039) maximum in 20 consecutive sprocket hole locations.
(3) Measured at bottom of standoff.
(4) P1 and F measured at egress from carrier tape.
(5) P and P2 measured at egress from carrier tape.
P0 12.7 (.500)
P1 See Note
Below
± 0.3 (±.012)
± 0.7 (±.028)
P2 See Note
Below
T0 10.2 (.400)
Maximum
T 0.7 (0.28)
± .02 (.008)
W 18.0 (.709)
+ 1.0/-0.5
(+.039/-.020)
W0 15mm or 6mm + 1.0/-0.8
(.561) (.236) (+.039/-.031)
W1 9.0 (.354)
+.075/-0.5
(+.030/-.020)
W2 12mm (.472) Maximum
P2
P
➀➁
A1
A
T0
ΔH
On polar devices, the positive (+) lead exits from container first.
* Lead spacings are 2.5mm (.098") center-to-center (T350 A-H)
** Lead spacings are 5.0mm (.197") center-to-center
# Lead spacings are 6.35mm (.25") center-to-center
+ Lead spacings are 3.18mm (.125") center-to-center
F Dimensions:
0.100" ± .015
0.125" ± .015
0.200" ± .015
0.250" ± .015"
0.100 " ± .015 (3 leaded)
P1 Dimensions:
Lead
Spacing
0.100" – 0.200 ± .028"
0.125" – 0.187 ± .028"
0.200" – 0.150 ± .028"
0.250" – 0.125 ± .028"
0.100" – 0.100 ± .028" ( 3 leaded)
F
T396/8*
L
T350/1*
W
H0
T352/3/6**
T354#
T355+
D0
d
T
L1
P1 P0
H1
W2 H
W1
W0
W2
1MM Max.
(.039")
Tape
Carrier
Tantalum Molded Radial – ARIS Specification (Automatic Radial Insertion System)
Tantalum Molded Tape and Reel Dimensions in Millimeters & (Inches)
Dimension
Nominal
Symbol mm (inch)
Tolerance
mm (inch)
Dimension
Symbol
Nominal
mm (inch)
Body Height (1)
A
Body Width (1)
Sprocket Hole
Diameter
Lead Diameter
A1
D0
d
Lead Center (5)
F
Component Base
to Tape Center (2)(4)(6)
Lead Standoff
Height
Component Height
Above Tape Center
Component Alignment
Front to Rear
Cut Out Length
H
H0
H1
ΔH
L
Lead Protrustion
L1
10.50 (.413)
15.24 (.600)
4.0 (.157)
± .38 (±.015)
Maximum
Maximum ± .38
± (.015)
± 0.3 (± .012)
0.51 or 0.64
(.020) (.025)
5.0 2.5
(.197) (.098)
16.0 - 21.0
(.630 - .827)
N/A
± 0.05 or ± .03
(± .001)
+ 0.8/ - 0.2
(+ .032/ -.008)
Reference Only
32.25 (1.270) Maximum
0
11.0 (.433)
± 2.0
(± .079)
Maximum
2.0 (.079)
Maximum
Component Pitch (5)
Sprocket Hole
Pitch (3)
Sprocket Hole
Center to Lead
Center (4) (5)
Sprocket Hole Center
to Component Center
Body Thickness
Total Tape Thickness
Carrier Tape Width
Hold-Down Tape
Width
Sprocket Hole
Location
Hold-Down Tape
Location
P 12.7 (.500)
P0 12.7 (.500)
P1 3.85 4.76 5.1
(.152) (.188) (.201)
P2 6.35 (.250)
T0 6.35 (.250)
T 0.7 (0.28)
W 18.0 (.709)
W0 15 or 6
(.561) (.236)
W1 9.0 (.354)
W2 3.0 or 12.0
(.118) (.472)
Notes: (1) See page 50 for T330, page 53 for T340 and page 59 for T35X specific dimensions.
(2) Reference Only
(3) Cumulative pitch error ± 1.0mm (.039") maximum in 20 consecutive sprocket hole locations.
(4) Measured at bottom of standoff.
(5) P, P1 and F measured at egress from carrier tape.
(6) H dimensions for T370 D and E 16.5mm ± 0.5mm (0.650" ± 0.020")
On polar devices, the positive (+) lead exits from container first.
* Lead spacings are 2.5mm (.098") center-to center
** Lead spacings are 5.0mm (.197") center-to-center.
Tolerance
mm (inch)
± 1.0 (± .039)
± 0.3 (±.012)
± 0.7 (±.028)
± 1.3 (±.051)
± 1.3 Maximum
± .02 (±.008)
+ 1.0/-0.5
(+.039/-.020)
+ 1.0/-0.8
(+.039/.031)
+.075/-0.5
(+.030/-.020)
Maximum
P2
➀➁
P
F
T370 W
A1
A
H1
W2 H
W1
W0
T340**
W2
T330**
D0
dT
L1
P1 P0
72 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606 (864) 963-6300

11 Page







PáginasTotal 13 Páginas
PDF Descargar[ Datasheet T359Dxxxxxx.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
T359DxxxxxxTantalum Dipped / RadialKemet Electronics
Kemet Electronics

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar