DataSheet.es    


PDF B6TY-SO4LT Data sheet ( Hoja de datos )

Número de pieza B6TY-SO4LT
Descripción B6TWorkbench User Manual
Fabricantes Omron 
Logotipo Omron Logotipo



Hay una vista previa y un enlace de descarga de B6TY-SO4LT (archivo pdf) en la parte inferior de esta página.


Total 19 Páginas

No Preview Available ! B6TY-SO4LT Hoja de datos, Descripción, Manual

www.DataSheet4U.com
B6TW / B6TY-S04LT / B6TY-S08NF
B6TWorkbench
User’s Manual
OMRON KURAYOSHI CO., LTD.
1
2794900-7A

1 page




B6TY-SO4LT pdf
www.DataSheet4U.com
1. Overview
This product connects the touch sensor IC (B6TS-04LT [4ch type] or B6TS-08NF [8ch type]) to a
personal computer in odrer to set the operation monitoring parameters. (Hereinafter, the touch sensor
IC is simply called the B6TS.)
The B6TS is connected to the personal computer via a serial port.
2. List of Delivery Components
Check for the presence of all components. When there are missing components, please contact our
sales representative.
Components delivered
B6TS I/F Board (B6TW)
Serial communication cable (Dsub 9pin cross)
CD-ROM
Sample board (B6TY-S04LT or B6TY-S08NF)
Flat cable
Quantity
1
1
1
1 (either
board) *
1
* Either of the following sample boards is delivered according to the model of this product.
B6TY-S04LT (4ch sample board: B6TS-04LT mounted as a touch sensor IC)
B6TY-S08LT (8ch sample board: B6TS-08NF mounted as a touch sensor IC)
3. Environmental Conditions for Use
3.1 Environmental Conditions
Item
Specification
Temperature Use: 0 to40
Storage: -15 to50
Humidity
Use: Below 85%RH (no dew condensation or freezing)
Storage: Below 85%RH (no dew condensation or freezing)
Ambient gas There must not be corrosive gas around.
3.2 Operating Environment
Item
Operating Environment
Host computer
IBM PC/AT compatible with Pentium III installed
OS Windows®2000 or Windows®XP
Memory capacity 64MB or more
Hard disk capacity 20MB or more
Interface
Serial port (COM) 38400bps [for B6TS I/F board connection]
* When a personal computer is not equiped with a serial port, use
the USB-serial conversion table.
Supply voltage
B6TS I/F Board: 3.0-5.5DVC
4ch sample board (B6TY-S04LT): 3.1-5.5DVC
8ch sample board (B6TY-S08LT): 4.5-5.5DVC
* Supply voltage varies between the boards. When using this
product, be sure to confirm supply voltage.
Dissipation current Below 200mA (including the B6TS I/F board and sample board)
5

5 Page





B6TY-SO4LT arduino
www.DataSheet4U.com
5.2.4 Reading and Writing the Parameters
The B6TS setup parameters can be read and written via the B6TS I/F board. Click the “Setup
Parameters” button on the main menu. A window appears as shown in the following figure.
Click the “Read from B6TS” button at lower left corner of the window to display the current B6TS
parameters. When this button is first clicked after this software has been activated, the message
“B6Tworkbench is not connected.” may be displayed. In this case, click the button again.
When this “Write to B6TS” button is clicked after the necessary items are set, the parameters are
written to B6TS.
In addition, the “Write to file” or “Read from file”button can be used to save the current display
parameters in a file of the personal computer or to read them from the file.
5.2.5 Explanation of Parameters
- General settings (MODE)
- Output Mode (CON)
The output configuration of the B6TS detection results is selected.
Data communication (“serial”) using either serial communication (SPI-compliant) or by
turning the terminal On or Off depending on the detection result (“On/Off” ) can be
selected.
- CHG active (CHG)
The B6TS measurement status can be monitored using the CHG signals.
Either turning the CHG terminal on “High” for every measurement (“Every
Measurement”) or turning it on “High” (“On/Off” ) for every status change from touch to
non-touch and vice versa in any measurement channel can be selected.
- Drift Compensation (DC)
The touch/non-touch measurement result varies depending on ambient conditions.
Whether or not to compensate for the touch/non-touch measurement according to this
change can be selected.
When “Disable” is selected, touch/nontouch evaluation takes place using the setting
On/Off threshold value.
When “Enable” is selected, the On/Off threshold is compensated dynamically depending
on the ambient conditions.
However, note that drift compensation is effective at times without touch assessment.
No drift compensation takes place even when “Enable” has been selected so long as
“touch” is judged as the measurement result of B6TS.
11

11 Page







PáginasTotal 19 Páginas
PDF Descargar[ Datasheet B6TY-SO4LT.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
B6TY-SO4LTB6TWorkbench User ManualOmron
Omron

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar