|
|
PDF 27R411T Data sheet ( Hoja de datos )
| Número de pieza | 27R411T | |
| Descripción | Users Guide | |
| Fabricantes | RCA | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de 27R411T (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
wwwwww.Da.DtaSahteaeSt4Uh.ecoemt4U.com
Television
User's Guide
Retourner le cahier pour la
version française
TOCOM 1616332A
Changing Entertainment. Again.
1 page  
Chapter 1: Connections & Setup
wwwwww.Da.DtaSahteaeSt4Uh.ecoemt4U.com
Things to Consider Before You Connect
Protect Against Power Surges
• Connect all components before you plug any of their power cords into the wall outlet.
• Turn off the TV and/or component before you connect or disconnect any cables.
• Make sure all antennas and cables are properly grounded. Refer to the Important Safety Instructions
packed separately.
Protect Components from Overheating
• Don’t block ventilation holes on any of the components. Arrange the components so that air can circulate
freely.
• Don’t stack components.
• If you place components in a stand, make sure you allow adequate ventilation.
• If you connect an audio receiver or amplifier, place it on the top shelf so the heated air from it won’t flow
around other components.
Position Cables Properly to Avoid Audio Interference
• Insert each cable firmly into the designated jack.
• If you place components above the TV, route all cables down the side of the back of the TV instead of
straight down the middle of the TV.
• If your antenna uses 300-ohm twin lead cables, do not coil the cables. Also, keep the twin lead cables
away from audio/video cables.
Important Stand and Base Safety Information
Choose the location for your TV carefully. Place the TV on a stand or base that is of adequate size and strength
to prevent the TV from being accidentally tipped over, pushed off, or pulled off. This could cause personal
injury and/or damage the TV. Refer to the Important Safety Instructions packed separately.
Use Indirect Light
Don’t place the TV where sunlight or room lighting will be directed toward the screen. Use soft or indirect
lighting.
Cables Needed to Connect Components to Your TV
The pictures below show the cables needed for the connections represented in this book.
Coaxial cable
S-Video cable
Audio/Video cables
Chapter 1
Graphics contained within this publication are for representation only.
3
5 Page 
Chapter 2: Using the Remote Control
wwwwww.Da.DtaSahteaeSt4Uh.ecoemt4U.com
Indicator
DVD ON OFF
VCR TV
VOL CH
MUTE GO BACK
CLEAR
MENU
OK
PRESETS
CC
1
SKIP
INFO
GUIDE
2
3
4 56
7
INPUT
89
0 ANTENNA
REVERSE
PLAY
FORWARD
RECORD
STOP
PAUSE
AGAIN
SPEED
ZOOM OPEN CLOSE
SEARCH
Button Descriptions for TV Mode
Arrows Used to highlight different items in the TV menu and to adjust the menu
controls.
Indicator Indicates the programming mode when programming the remote to
control components. Lights when you press a valid button on the remote. Flickers
when a button is pressed and the batteries are low.
(0-9) Number Buttons Enter channel numbers and time settings directly
through the remote control.
To enter a one-digit channel, enter a zero first. To enter a two-digit channel, press
the two digits and expect a few seconds delay. This is if you want to enter a third
digit.
CC Toggles closed captioning on and off.
CH + or CH - Scans up or down through the current channel list. Press once to
change the channel up or down; press and hold to continue changing channels.
CLEAR Removes any menu or display from the screen and returns you to normal
viewing.
GO BACK Returns you to the previous channel.
INFO Brings up the channel banner.
INPUT Toggles through the available input sources (VID1/SVID1, FRNT, and
current channel).
MENU Brings up the Main menu.
MUTE Reduces the TV’s volume to its minimum level. Press again to restore the
volume.
OK When in the menu system, selects highlighted items.
ON•OFF When in TV mode, turns the TV on and off. If in another mode (VCR or
DVD) and programmed, will turn the component on and off.
PRESETS Picture options are reset to original factory settings.
SKIP Press once before changing channels and the TV will wait 30 seconds before
returning to the original channel. Press repeatedly to add more time.
TV Turns on the TV and puts the remote in TV mode. Also displays current status.
VOL – or VOL + Decreases or increases the TV’s volume.
Button Descriptions for DVD and VCR Modes
AGAIN In DVD mode, replays the last several seconds of the title you’re playing.
ANTENNA In VCR mode, functions as a TV/VCR button.
DVD Puts the remote in DVD mode and, if auto tuning is enabled, will turn on
the TV and tune to the correct video input channel. Also used with the ON•OFF
button to turn on other compatible DVD players.
GUIDE If you’re operating another component that has an on-screen program
guide, this button accesses the on-screen guide.
Chapter 2 Graphics contained within this publication are for representation only.
9
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet 27R411T.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| 27R411T | Users Guide | RCA |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |