|
|
PDF U840A Data sheet ( Hoja de datos )
| Número de pieza | U840A | |
| Descripción | TOILET TISSUE DISPENSER | |
| Fabricantes | ETC | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de U840A (archivo pdf) en la parte inferior de esta página. Total 1 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
&
Architectural
Washroom R
Accessories INC.
Janitorial Washroom Accessories
U840A
TOILET TISSUE DISPENSER
JOB #:
Item:
QTY:
6”
152mm
6 3/4”
171mm
12”
305 mm
Two
Spindles
S
S
SPECIFICATIONS:
INSTALLATION:
Body: Fabricated of type 304 #22 ga stainless steel with #4
satin finish. Concealed inner dispensing mechanism is type
304 #18 ga stainless steel.
Back: Fabricated of type 304 #18 ga stainless steel with
multiple welds to cabinet body forming a one piece
construction.
Hood: Fabricated of type 304 #18 ga stainless steel finished to
match cabinet body. Hood is secured with stainless steel hinge
rivets to cabinet body. Top roll of tissue will not drop down
unless the bottom roll has been depleted. When unit is closed,
this will provide a theft resistant, non-control operation and
reduce vandalism.
Locks: Pin tumbler, commercial quality locks keyed like all
other A & J cabinets.
Spindles: (U005A) Fabricated of one-piece molded high
impact black ABS material.
Provide an area on mounting surface at desired or specified
location. Open cabinet, remove spindles and hold unit to wall
at desired location. Transfer mounting points and drill pilot
holes. Secure unit with proper fasteners per each application.
Load toilet tissue on rollers, place in concealed track and
close hood. Raise lower roll against upper and take hand
away. Lower roll should fall into place with upper roll
remaining up above the hood line. If loaded properly, top roll
will not fall for use until bottom roll has been depleted. When
servicing dispenser, full rolls must be used on both spindles to
insure proper operation.
All toilet tissue dispensers that meet ADA code cannot have
any type of control delivery. (4.16)
Recommend: Type CP801,CP802, CP807, CP808 or CP809
toilet tissue.
Overall Size: 6”W x 12”H x 6 3/4”D
152mm x 305mm x 171mm
Capacity: 2 Standard size rolls up to 5 3/4” diameter.
*Sheet capacity may vary from roll to roll depending on the
manufacturer and sheet style selected.
APPLICATION:
To provide a surface mounted stainless steel, hooded, dual roll
toilet tissue dispenser that has a non-control delivery. When
mounted properly, unit will comply with ADA Code 4.16.
This information is subject to change without formal notice. If you need additional help, A&J Washroom accessories, Inc. has a technical support staff that is ready to assist you at Fax (845) 562-3391,
email: [email protected] or visit our web at http://www.ajwashroom.com
Copyright 2000 A&J Washroom Accessories, Inc.
1 page | ||
| Páginas | Total 1 Páginas | |
| PDF Descargar | [ Datasheet U840A.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| U840A | TOILET TISSUE DISPENSER | ETC |
| U840B | Digital / Wipe-Wash Control |  TEMIC Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |