|
|
PDF LA6587T Data sheet ( Hoja de datos )
| Número de pieza | LA6587T | |
| Descripción | Monolithic Linear IC Fan Motor Driver BTL Driver Single-Phase Full-Wave | |
| Fabricantes | Sanyo Semicon Device | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LA6587T (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
Ordering number : ENA0603
LA6587T
Monolithic Linear IC
Fan Motor Driver
BTL Driver Single-Phase Full-Wave
Overview
The LA6587T is single-phase bipolar fan motor is driven, through BTL output linear drive, at high efficiency, low power,
and low sound by suppressing the reactive power. Lock protection, rotary signal (FG, 1/2FG) circuits are incorporated,
which is optimum for the notebook PC, consumer equipment power supply, car audio system, CPU cooler, etc. that require
high reliability and low noise.
Functions
• Single-phase full-wave linear drive by BTL output (gain resistance 1kΩ-360kΩ, 51dB)
: No switching noise, which is optimum for equipment requiring silence, such as consumer equipment power supply, car
audio system, etc.
• Low-voltage operation possible, with wide operating voltage range (2.2 to 14.0V)
• Low saturation output (Upper + lower saturation voltage : VOsat (total) = 1.1Vtyp, IO = 100mA)
: High coil efficiency with low current drain. Additionally, IC itself generates only small heat.
• Built-in lock protection and automatic reset circuits
• Built-in FG & 1/2FG outputs
• Built-in Hall bias (VHB = 1.5V)
• Thermal protection circuit
: When the large current flows due to output short-circuit and the IC chip temperature exceeds 180°C, this protective
circuit suppresses the drive current to prevent burn and damage to IC.
• Extra-small package (MSOP10)
Specifications
Absolute Maximum Ratings at Ta = 25°C
Parameter
Output voltage
Allowable power dissipation
Output current
Output withstand voltage
RD/FG output pin output
withstand voltage
RD/FG output current
Symbol
VCC max
Pd max
IOUT max
VOUT max
VRD/FG max
Conditions
Mounted on a specified board*
IRD/FG max
Ratings
Unit
15 V
400 mW
0.6 A
15 V
15 V
10 mA
Continued on next page.
Any and all SANYO Semiconductor products described or contained herein do not have specifications
that can handle applications that require extremely high levels of reliability, such as life-support systems,
aircraft's control systems, or other applications whose failure can be reasonably expected to result in
serious physical and/or material damage. Consult with your SANYO Semiconductor representative
nearest you before using any SANYO Semiconductor products described or contained herein in such
applications.
SANYO Semiconductor assumes no responsibility for equipment failures that result from using products
at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor
products described or contained herein.
D0606 MS PC B8-7868 No.A0603-1/5
1 page  
www.DataSheet4U.com
Sample Application Circuit
LA6587T
Di
*1
Cr
R1
*2 H
*5
VCC
1/2FG
FG
HB
IN- OUT1
IN+
CT
OUT2
GND
*6
On board element
*4
HB
*3
H
IN-
IN+
*1 : When the breakdown protective DI at reverse connection is to be used, it is necessary to insert the capacitor Cr to
secure the regenerative current route. Similarly, Cr must be provided to enhance the reliability when there is no
capacitor near the fan power line.
*2 : To obtain Hall bias from VCC, carry out 1VCC bias as shown in the figure. Linear driving is made through
voltage control of the coil by amplifying the Hall output. When the Hall element output is large, the startup
performance and efficiency are improved. Adjustment of the Hall element can reduce the noise further.
*3 : To obtain Hall bias from the HB pin, carry out constant-voltage bias at about 1.5V, which enables the Hall
element to generate the stable Hall output satisfactory in temperature characteristics.
*4 : Keep this open when not using.
*5 : When the wiring from the Hall output to IC Hall input is long, noise may be carried through the wiring.
In this case, insert the capacitor as shown in the figure.
Specifications of any and all SANYO Semiconductor products described or contained herein stipulate the
performance, characteristics, and functions of the described products in the independent state, and are
not guarantees of the performance, characteristics, and functions of the described products as mounted
in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an
independent device, the customer should always evaluate and test devices mounted in the customer's
products or equipment.
SANYO Semiconductor Co., Ltd. strives to supply high-quality high-reliability products. However, any
and all semiconductor products fail with some probability. It is possible that these probabilistic failures
could give rise to accidents or events that could endanger human lives, that could give rise to smoke or
fire, or that could cause damage to other property. When designing equipment, adopt safety measures
so that these kinds of accidents or events cannot occur. Such measures include but are not limited to
protective circuits and error prevention circuits for safe design, redundant design, and structural design.
In the event that any or all SANYO Semiconductor products (including technical data,services) described
or contained herein are controlled under any of applicable local export control laws and regulations, such
products must not be exported without obtaining the export license from the authorities concerned in
accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or
otherwise, without the prior written permission of SANYO Semiconductor Co., Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification"
for the SANYO Semiconductor product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not
guaranteed for volume production. SANYO Semiconductor believes information herein is accurate and
reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual
property rights or other rights of third parties.
This catalog provides information as of December, 2006. Specifications and information herein are subject
to change without notice.
PS No.A0603-5/5
5 Page | ||
| Páginas | Total 5 Páginas | |
| PDF Descargar | [ Datasheet LA6587T.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LA6587T | Monolithic Linear IC Fan Motor Driver BTL Driver Single-Phase Full-Wave | Sanyo Semicon Device |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |