DataSheet.es    


PDF LH4266 Data sheet ( Hoja de datos )

Número de pieza LH4266
Descripción SPDT RF Switch
Fabricantes National Semiconductor 
Logotipo National Semiconductor Logotipo



Hay una vista previa y un enlace de descarga de LH4266 (archivo pdf) en la parte inferior de esta página.


Total 8 Páginas

No Preview Available ! LH4266 Hoja de datos, Descripción, Manual

www.DataSheet4U.com
October 1988
LH4266 SPDT RF Switch
General Description
The LH4266 is a single pole double throw switch intended
for RF and video switching applications The device has a
TTL compatible control signal and can be configured as a
multiplexer or demultiplexer which will fulfill most switching
needs
The non-selected input may be terminated to provide a
match to the source driving that port and prevent spurious
oscillations that might occur from an unterminated transmis-
sion line
Features
Y Single pole double throw (SPDT)
Y DC to 150 MHz
Y a27 5 dBm maximum signal (50X)
Y Low insertion loss 1 5 dB (50X)
Y Non-selected input terminated
Y Break before make
Y TTL compatible control signal
Y Internal power supply bypassing
Applications
Y ATE pin driver switch
Y Computer RF switch
Y Tester switching matrix
Y RF voltage multiplexer
Connection Diagram
Note NC means no internal connection
Top View
Order Number LH4266CD or LH4266D
See NS Package Number D24I
TL K 9404 – 1
C1995 National Semiconductor Corporation TL K 9404
RRD-B30M115 Printed in U S A

1 page




LH4266 pdf
Leakage Current Equivalent Test Circuit
Same test for Input 2
TL K 9404 – 11
Test Circuit for Isolation Input to Output
for ease of use Thus for high frequency applications bypass
capacitors are not required however at low frequencies (10
MHz or less) a 4 7 mF bypass capacitor for each supply is
recommended
Due to the unique design of the LH4266 it can easily be
used as a multiplexer or demultiplexer In fact several units
can be connected to give a 1 to 4 multiplexer or a 4 to 1
demultiplexer by simply adding the required units as shown
in Figures 2 to 5
The action of the switches can be seen in the following truth
table
LH4266 Truth Table
Control
Low e 0
High e 1
Pin 24
Input 2
On
Off
Pin 13
Input 1
Off
On
Double Sided Board Bottom Side
TL K 9404 – 12
Applications Information LH4266
The LH4266 uses hybrid technology to give increased cir-
cuit performance In order to maintain its excellent cross
talk and feedthru specifications proper RF grounding and
shielding should be incorporated in the printed circuit board
layout For example the input traces should not run next to
output traces and grounds should be provided by a ground
plane under the device (see Figure 1a b for suggested PC
board layout)
The device contains two internal termination resistors and
switches If termination of the non-selected input is desired
connect the termination pin to the adjacement input pin and
the deselected input will be terminated with approximately
50X
Note that the internal termination resistors are internally
connected to the device’s ground pin Thus if the internal
termination resistors are used then the input ground planes
should remain isolated from the output ground plane (as in
Figure 1 ) so as not to form a ground loop When using exter-
nal termination resistors at the input the resistors should be
connected to their respective ground planes and pin 16
should be tied to input1’s ground plane while pin 21 is tied
to input2’s ground plane Since pins 16 and 21 are internally
connected to the device ground pin the input and output
ground planes should remain isolated LH4266’s power sup-
plies are internally bypassed with high frequency capacitors
5
TL K 9404 – 2
FIGURE 1a LH4266 Recommended
Printed Circuit Board Layout
Double Sided Board Top Side
TL K 9404 – 13
FIGURE 1b LH4266 Recommended
Printed Circuit Board Layout

5 Page










PáginasTotal 8 Páginas
PDF Descargar[ Datasheet LH4266.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
LH4266SPDT RF SwitchNational Semiconductor
National Semiconductor

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar