|
|
Número de pieza | AZ100E131 | |
Descripción | ECL/PECL 4-bit D Flip-Flop | |
Fabricantes | Arizona Microtek | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de AZ100E131 (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
No Preview Available ! www.DataSheet4U.com
ARIZONA MICROTEK, INC.
AZ10E131
AZ100E131
ECL/PECL 4-bit D Flip-Flop
FEATURES
PACKAGE AVAILABILITY
• 1100 MHz Min. Toggle Frequency
• Differential Outputs
PACKAGE PART NUMBER MARKING NOTES
• Individual and Common Clocks
• Individual Resets (asynchronous)
• Paired Sets (asynchronous)
• Operating Range of 4.2V to 5.46V
PLCC 28
AZ10E131FN
AZM10E131
<Date Code>
1,2
PLCC 28
AZ100E131FN
AZM100E131
<Date Code>
1,2
1 Add R2 at end of part number for 13 inch (2.5K parts) Tape & Reel.
• 75kΩ Internal Input Pulldown Resistors 2 Date code format: “YY” for year followed by “WW” for week.
• Direct Replacement for On Semiconductor
MC10E131 & MC100E131
DESCRIPTION
The AZ10/100E131 is a quad master-slave D-type flip-flop with differential outputs. Each flip-flop may be
clocked separately by holding Common Clock (CC) LOW and using the Clock Enable (C¯¯En) inputs for clocking.
Common clocking is achieved by holding the C¯¯En inputs LOW and using CC to clock all four flip-flops. In this
case, the C¯¯En inputs perform the function of controlling the common clock to each flip-flop.
Individual asynchronous resets are provided (Rn). Asynchronous set controls (Sn) are ganged together in pairs,
with the pairing chosen to reflect physical chip symmetry.
Data enters the master when both CC and C¯¯En are LOW, and transfers to the slave when either CC or C¯¯En (or
both) go HIGH.
NOTE: Specifications in ECL/PECL tables are valid when thermal equilibrium is established.
CE3
D3
R3
25
26
27
D2 CE2 R2 VCCO Q3
24
23 22
21
20
Q3
19
18
17
Q2
Q2
S12 28
VEE
CC
S03
1
2
3
Pinout: 28-Lead
PLCC (top view)
16 VCC
15 Q1
14 Q1
13 Q0
D0 4
12 Q0
5 6 7 8 9 10 11
CE0
R0
D1 CE1
R1
NC VCCO
* All VCC and VCCO pins are tied together on the die.
1630 S. STAPLEY DR., SUITE 127 • MESA, ARIZONA 85204 • USA • (480) 962-5881 • FAX (480) 890-2541
www.azmicrotek.com
1 page AZ10E131
AZ100E131
PACKAGE DIAGRAM
PLCC 28
DIM
A
B
C
E
F
G
H
J
K
R
U
V
W
X
T
Z
G1
K1
MILLIMETERS
MIN MAX
12.32 12.57
12.32 12.57
4.20 4.57
2.29 2.79
0.33 0.48
1.27 BSC
0.66 0.81
0.51
0.64
11.43 11.58
11.43 11.58
1.07 1.21
1.07 1.21
1.07 1.42
0.50
2O 10O
10.42 10.92
1.02
INCHES
MIN MAX
0.485 0.495
0.485 0.495
0.165 0.180
0.090 0.110
0.013 0.019
0.050 BSC
0.026 0.032
0.020
0.025
0.450 0.456
0.450 0.456
0.042 0.048
0.042 0.048
0.042 0.056
0.020
2O 10O
0.410 0.430
0.040
NOTES:
1. DATUMS –L-, -M-, AND –N- DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS
PLASTIC BODY AT MOLD PARTING LINE.
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM –T-, SEATING PLANE.
3. DIMENSIONS R AND U DO NOT INCLUDE
MOLD FLASH. ALOWABLE MOLD FLASH IS
0.010mm (0.250in.) PER SIDE.
4. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN
THE PACKGE BOTTOM BY UP TO 0.012mm
(0.300in.). DIMENSIONS R AND U ARE
DETERMINED AT THE OUTERMOST
EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, THE BAR
BURRS, GATE BURRS AND INTERLEAD FLASH,
BUT INCLUDING ANY MISMATCH BETWEEN
THE TOP AND BOTTOM OF THE PLASTIC
BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE SMALLER THAN 0.025mm
(0.635in.).
November 2006 * REV - 3
www.azmicrotek.com
5
5 Page |
Páginas | Total 6 Páginas | |
PDF Descargar | [ Datasheet AZ100E131.PDF ] |
Número de pieza | Descripción | Fabricantes |
AZ100E131 | ECL/PECL 4-bit D Flip-Flop | Arizona Microtek |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |