|
|
PDF GP2A200LCS Data sheet ( Hoja de datos )
| Número de pieza | GP2A200LCS | |
| Descripción | Reflective Type Photointerrupter | |
| Fabricantes | Sharp Electrionic | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de GP2A200LCS (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
GP2A200LCS
GP2A200LCS
Light Modulation, Reflective
Type Photointerrupter
s Features
1. Light modulation type which is free from external disturbing
light
2. Long focal distance type (Detecting range : 5 to 15mm)
3. Compact type
s Applications
1. Copiers
2. Facsimiles
3. Laser beam printers
s Absolute Maximum Ratings
(Ta=25˚C)
Parameter
Symbol Rating
Unit
Supply voltage
VCC −0.5 to +7
V
Output voltage
VO 30 V
*1 Output current
IOL 50 mA
Operating temperature
Topr −10 to +70 ˚C
*2 Storage temperature
Tstg −20 to +80 ˚C
*1 Sink current refer to Fig.5
*2 The connector should be plugged in/out at normal temperature
s Outline Dimensions
33
3.1 17.7
Optical center
(6.8)
(Unit : mm)
6.2 6
12
Connector made by JAPAN Amp 175768-3
7.8
View A
26.5
φ3+−00.2
123
View A
1 VCC
2 VO
3 GND
g ( ) : Reference dimensions
g Unspecified tolerances shall be as follows.
Dimensions(d)
d<6.0
6.0<=d<14.0
14.0<=d
Tolerance
±0.2
±0.3
±0.4
Internal connection diagram
Reflective object
Demodulator circuit
Constant voltage circuit
3
2
Amp.
1
Comparator Oscillation circuit Sync. detecting circuit
* "OPIC" (Optical IC) is a trademark of the SHARP Corporation.
An OPIC consists of a light-detecting element and signal-processing circuit
integrated onto a single chip.
Notice In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
Internet Internet address for Electronic Components Group http://www.sharp.co.jp/ecg/
1 page  
Application Circuits
NOTICE
qThe circuit application examples in this publication are provided to explain representative applications of
SHARP devices and are not intended to guarantee any circuit design or license any intellectual property
rights. SHARP takes no responsibility for any problems related to any intellectual property right of a
third party resulting from the use of SHARP's devices.
qContact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
SHARP reserves the right to make changes in the specifications, characteristics, data, materials,
structure, and other contents described herein at any time without notice in order to improve design or
reliability. Manufacturing locations are also subject to change without notice.
qObserve the following points when using any devices in this publication. SHARP takes no responsibility
for damage caused by improper use of the devices which does not meet the conditions and absolute
maximum ratings to be used specified in the relevant specification sheet nor meet the following
conditions:
(i) The devices in this publication are designed for use in general electronic equipment designs such as:
--- Personal computers
--- Office automation equipment
--- Telecommunication equipment [terminal]
--- Test and measurement equipment
--- Industrial control
--- Audio visual equipment
--- Consumer electronics
(ii)Measures such as fail-safe function and redundant design should be taken to ensure reliability and
safety when SHARP devices are used for or in connection with equipment that requires higher
reliability such as:
--- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.)
--- Traffic signals
--- Gas leakage sensor breakers
--- Alarm equipment
--- Various safety devices, etc.
(iii)SHARP devices shall not be used for or in connection with equipment that requires an extremely
high level of reliability and safety such as:
--- Space applications
--- Telecommunication equipment [trunk lines]
--- Nuclear power control equipment
--- Medical and other life support equipment (e.g., scuba).
qContact a SHARP representative in advance when intending to use SHARP devices for any "specific"
applications other than those recommended by SHARP or when it is unclear which category mentioned
above controls the intended use.
qIf the SHARP devices listed in this publication fall within the scope of strategic products described in the
Foreign Exchange and Foreign Trade Control Law of Japan, it is necessary to obtain approval to export
such SHARP devices.
qThis publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under
the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any
means, electronic or mechanical, for any purpose, in whole or in part, without the express written
permission of SHARP. Express written permission is also required before any use of this publication
may be made by a third party.
qContact and consult with a SHARP representative if there are any questions about the contents of this
publication.
115
5 Page | ||
| Páginas | Total 5 Páginas | |
| PDF Descargar | [ Datasheet GP2A200LCS.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| GP2A200LCS | Reflective Type Photointerrupter | Sharp Electrionic |
| GP2A200LCS0F | Refl ective Photointerrupter | Sharp Electrionic |
| GP2A200LCS0F | Refl ective Photointerrupter | Sharp Electrionic |
| GP2A200LCSCF | Refl ective Photointerrupter | Sharp Electrionic |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |