|
|
PDF W79E216A Data sheet ( Hoja de datos )
| Número de pieza | W79E216A | |
| Descripción | (W79E216A / W79E217A) 8-BIT MICROCONTROLLER | |
| Fabricantes | Winbond | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de W79E216A (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
Preliminary W79E217A/216A Data Sheet
TABLE OF CONTENTS-
8-BIT MICROCONTROLLER
1 GENERAL DESCRIPTION .........................................................................................................................................5
2 FEATURES ......................................................................................................................................................................5
3 PARTS INFORMATION LIST ....................................................................................................................................6
3.1 LEAD FREE (ROHS) PARTS INFORMATION LIS T................................................................................................. 6
4 PIN CONFIGURATION................................................................................................................................................7
5 PIN DESCRIPTION .......................................................................................................................................................9
5.1 PORT 4...................................................................................................................................................................... 11
6 MEMORY ORGANIZATION.....................................................................................................................................12
6.1 PROGRAM M EMORY (ON-CHIP FLASH)............................................................................................................... 12
6.2 DATA MEMORY ........................................................................................................................................................ 12
6.3 AUXILIARY SRAM................................................................................................................................................... 13
6.4 2-KB NVM DATA FLASH MEMORY ..................................................................................................................... 13
6.4.1 Operation .......................................................................................................................................................15
7 SPECIAL FUNCTION REGISTERS ......................................................................................................................18
8 INSTRUCTION SET ....................................................................................................................................................69
8.1 INSTRUCTION TIMING ............................................................................................................................................. 76
8.1.1 External Data Memory Access Timing ................................................................................................78
9 POWER M ANAGEMENT ..........................................................................................................................................81
9.1 IDLE MODE............................................................................................................................................................... 81
9.2 POWER DOWN MODE ............................................................................................................................................ 81
10 RESET CONDITIONS ............................................................................................................................................83
10.1 SOURCES OF RESET............................................................................................................................................... 83
10.1.1 External Reset ..............................................................................................................................................83
10.1.2 Power-On Reset (POR) ............................................................................................................................83
10.1.3 Watchdog Timer Reset .............................................................................................................................83
10.2 RESET STATE.......................................................................................................................................................... 83
11 INTERRUPTS............................................................................................................................................................85
11.1 INTERRUPT SOURCES ............................................................................................................................................ 85
11.2 PRIORITY LEVEL STRUCTURE .............................................................................................................................. 85
11.2.1 Response Time............................................................................................................................................88
12 PROGRAMMABLE TIMERS/COUNTERS.....................................................................................................89
12.1 TIMER/COUNTERS 0 & 1....................................................................................................................................... 89
12.1.1 Time-Base Selection ..................................................................................................................................89
12.1.2 Mode 0 ............................................................................................................................................................89
12.1.3 Mode 1 ............................................................................................................................................................89
-1 -
Publication Release Date: December, 2006
Revision A0.2
1 page  
Preliminary W79E217A/216A Data Sheet
1 GENERAL DESCRIPTION
The W79E217/217 is a fast, 8051/52-compatible microcontroller with a redesigned processor core that
eliminates wasted clock and memory cycles . Typically, the W79E217/217 executes instructions 1.5 to
3 times faster than that of the traditional 8051/52, depending on the type of instruction, and the overall
performance is about 2.5 times better at the same crystal speed. As a result, with the fully-static CMOS
design, the W79E217/217 can accomplish the same throughput with a lower clock speed, reducing
power consumption.
The W79E217/217 provides 256 bytes of on-chip RAM; 2-KB of NVM memory Flash EPROM; 2-KB of
auxiliary RAM; seven 8-bit, bi-directional and bit-addressable I/O ports; an additional 4-bit port P4;
three 16-bit timer/counters; Motion Feedback Module support; 2 UART serial port s; 1 channels of I2C
with master/slave capability; 1 channels of Serial Peripheral Interface (SPI), 8 channels of 12 bit PWM
with configurable dead time and 8 channels of 10-bit ADC. These peripherals are all supported by 20
interrupt sources with 4 levels of priority.
The W79E217/217 also contains a 64/32-KB Flash EPROM whose contents may be updated in-
system by a loader program stored in an auxiliary, 4-KB Flash EPROM. Once the contents are
confirmed, it can be protected for security.
2 FEATURES
?? Fully-static-design 8-bit 4T-8051 CMOS microcontroller up to 40MHz .
?? 64/32-KB of in-system-programmable Flash EPROM (AP Flash EPROM).
?? 4-KB of Auxiliary Flash EPROM for the loader program (LD Flash EPROM). User can optionally
reboot from LD Flash EPROM by pull low at either P4.3 or P3.6 and P3.7, at external reset.
?? 2-KB auxiliary RAM, software-selectable, accessed by MOVX instruction.
?? 2-KB of NVM Data Flash EPROM for customer data storage used.
?? 256 bytes of scratch-pad RAM.
?? Seven 8-bit bi-directional ports; Port 0 has internal pull-up resisters enabled by software.
?? One 4-bit multipurpose I/O port4 with Chips select (CS) and boot function.
?? Three 16-bit timers.
?? One 16-bit Timer 3 for Motion Feed-Back Module.
?? Motion Feedback Module - QEI decoder and 3 Inputs Capture.
?? Eight channels of 12-bit PWM:-
?? Complementary paired output with programmable dead-time insertion.
?? Three modes: Edge aligned, center aligned and single shot.
?? Output override control for BLDC motor application.
?? 10-bit ADC with 8-channel inputs.
?? Two enhanced full-duplex UART with framing-error detection and automatic address recognition.
?? One channel of I2C with master/slave capability.
?? One channel of SPI with master/slave capability.
?? LCD driver output:-
?? 32segment X 4common.
?? 1/3 duty (1/3 bias), 1/4 duty (1/3 bias) driving mode can be selected.
?? LCD driver output pin can be used as DC output.
?? Software programmable access cycle to external RAM/peripherals.
?? 20 interrupt sources with four levels of priority.
?? Software reset function.
Publication Release Date: December, 2006
- 5 - Revision A0.2
5 Page 
Preliminary W79E217A/216A Data Sheet
DH1, DH2 I
Capacitor input for LCD driver.
COM0-
COM3
LCD common output s.
1/3 Duty 1/4 Duty
COM0 Used
Used
COM1 Used
Used
COM2 Used
Used
COM3 Not Used Used
The LCD alternating frequency can be selected by code option.
?? Note : TYPE I: input, O: output, I/O: bi-directional, H: pull-high, L: pull-low, D: open drain S: Schmitt Trigger
5.1 Port 4
Port 4, SFR P4 at address A5H, is a 4-bit multipurpose programmable I/O port which functions are I/O,
insert wait function and chip-select function. It has four different operation modes:
?? Mode 0 - P4.0 ~ P4.3 is 4-bit bi-directional I/O port which is the same as port 1. The default Port 4
is a general I/O function.
?? Mode1 - P4.0 ~ P4.3 are read data strobe signals which are synchronized with RD signal at
specified addresses. These read data strobe signals can be used as chip-select signals for
external peripherals.
?? Mode2 - P4.0 ~ P4.3 are write data strobe signals which are synchronized with WR signal at
specified addresses. These write data strobe signals can be used as chip-select signals for
external peripherals.
?? Mode3 - P4.0 ~ P4.3 are read/write data strobe signals which are synchronized with RD
or WR signal at specified addresses. These read/write data strobe signals can be used as chip-
select signals for external peripherals.
When Port 4 is configured with the feature of chip-select signals, the chip-select signal address range
depends on the contents of the SFR P4xAH, P4xAL, P4CONA and P4CONB. P4xAH and P4xAL
contain the 16-bit base address of P4.x. P4CONA and P4CONB contain the control bits to configure
the Port 4 operation mode.
- 11 -
Publication Release Date: December, 2006
Revision A0.2
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet W79E216A.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| W79E216A | (W79E216A / W79E217A) 8-BIT MICROCONTROLLER | Winbond |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |