DataSheet.es    


PDF V48C12xxxx Data sheet ( Hoja de datos )

Número de pieza V48C12xxxx
Descripción (V48x12xxxx) DC-DC Converter Module
Fabricantes Vicor Corporation 
Logotipo Vicor Corporation Logotipo



Hay una vista previa y un enlace de descarga de V48C12xxxx (archivo pdf) en la parte inferior de esta página.


Total 8 Páginas

No Preview Available ! V48C12xxxx Hoja de datos, Descripción, Manual

www.DataSheet4U.com
45
Features
DC input range: 250 - 425V
Input surge withstand: 500V for 100ms
DC output: 5V
Programmable output: 10 to 110%
Regulation: ±0.2% no load to full load
Efficiency: 80%
Maximum operating temperature:
100°C at full load
Power density: 61W/cubic inch
Height above board: 0.43 in. (10,9 mm)
Parallelable, with N+M fault tolerance
Low noise ZCS/ZVS architecture
Typical Applications: distributed power;
off-line systems using power PFC front-ends;
electric vehicles
375Vin / 5Vout / 100Watts
DC-DC Converter Module
Model Number V375C5C100A*
Shown actual size:
2.28 x 1.45 x 0.5 in
57,9 x 36,8 x 12,7 mm
Product Overview
This DC-DC converter module uses
2nd Generation power processing, control
and packaging technologies to provide the
performance, flexibility and cost effectiveness
expected of a mature power component.
For example, a plated-cavity core transformer
couples widely separated primary and
secondary windings, resulting in low in-to-
out parasitic capacitance and noise.
High frequency ZCS/ZVS switching,
advanced power semiconductor packaging
and thermal management provide high
power density with low temperature
gradients. Extensive use of silicon
integration results in 1/3 the part count
of a 1st Generation converter.
* Part Numbering
V 375 C 12 C 150 A
Absolute Maximum Ratings
Parameter
Rating
+In to –In voltage
-0.5 to +425.0
+In to –In voltage
500
PC to –In voltage
-0.5 to +7.0
PR to –In voltage
-0.5 to +7.0
+Out to –Out voltage
-0.5 to +7.0
SC to –Out voltage
-0.5 to +1.5
Isolation voltage (in to out)
3000
Isolation voltage (in to base)
1550
Isolation voltage (out to base)
500
Storage temperature (C–Grade) -40 to +125
Operating temperature (C–Grade) -20 to +100
Pin soldering temperature
500 (260)
Pin soldering temperature
750 (390)
Mounting torque
5 (0.57)
Input Voltage
24 = 24Vin
48 = 48Vin
300 = 300Vin
375 = 375Vin
A = Maxi
B = Mini
C = Micro
Output
Voltage
Output
Power
Pin
Style
Product Grade Temperatures (°C)
Grade Storage Operating
C = - 40 to +125 - 20 to +100
T = - 40 to +125 - 40 to +100
H = - 55 to +125 - 40 to +100
M = - 65 to +125 - 55 to +100
Base-
plate
For pin styles see page 6. Slotted baseplate
(style 1) requires no designator. For
threaded baseplate add a “2” to the end of
the part number. For thru-hole, add a “3”.
See page 7 for dimensions.
Thermal Resistance and Capacity
Parameter
Baseplate to sink; flat, greased surface
Baseplate to sink; thermal pad (P/N 20265)
Baseplate to ambient
Baseplate to ambient; 1000 LFM
Thermal capacity
Min
Unit
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Vrms
Vrms
Vrms
°C
°C
°F (°C)
°F (°C)
in-lbs (N-m)
Notes
<100ms
See part numbering chart on this
page for other product grades.
Baseplate
<5 sec; wave solder
<7 sec; hand solder
6 each, # 4-40 or M3
Typ Max Unit
0.24 °C/Watt
0.21 °C/Watt
10.9 °C/Watt
2.8 °C/Watt
48 Watt-sec/°C
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
V375C5C100A DC-DC Converter
Set your site on VICOR at www.vicorpower.com
Rev. 5.2
Page 1 of 8

1 page




V48C12xxxx pdf
CONTROL FUNCTIONS - SC PIN
Output Voltage Programming
The output voltage of the converter can be adjusted or
programmed via fixed resistors, potentiometers or voltage
DACs. See Figures 7 and 8.
Error
Amp
1k
0.033µF
1.23V
+Out
SC
–Out
RD
Trim Down
Load
Error
Amp
1k
0.033µF
1.23V
+Out
SC
–Out
RU
Trim Up
Load
RD (ohms) =
1,000 Vout
Vnom - Vout
Figure 7—Output voltage trim down circuit.
1,000 (Vout-1.23) Vnom
RU (ohms) = 1.23 (Vout-Vnom) –1,000
Figure 8—Output voltage trim up circuit.
Trim Down
1. This converter is not a constant power device – it has a
constant current limit. Hence, available output power is
reduced by the same percentage that output voltage is
trimmed down. Do not exceed maximum rated output current.
2. The trim down resistor must be connected to the –Out pin.
Trim Up
1. The converter is rated for a maximum delivered power. To ensure
that maximum rated power is not exceeded, reduce maximum
output current by the same percentage increase in output voltage.
2. The trim up resistor must be connected to the +Out pin.
3. Do not trim the converter above maximum trim range
(typically +10%) or the output over voltage
protection circuitry may be activated.
Trim resistor values calculated automatically:
On-line calculators for trim resistor values are available
on the vicor website at: vicorpower.com/tools.html.
Resistor values can be calculated for fixed trim up, fixed
trim down and for variable trim up or down cases for both
1st and 2nd Generation DC-DC converters.
In addition to trimming information, the web site and the
Applications Manual also include design tips, applications
circuits, EMC suggestions, thermal design guidelines and
PDF data sheets for all available Vicor products.
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
V375C5C100A DC-DC Converter
Set your site on VICOR at www.vicorpower.com
Rev. 5.2
Page 5 of 8

5 Page










PáginasTotal 8 Páginas
PDF Descargar[ Datasheet V48C12xxxx.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
V48C12xxxx(V48x12xxxx) DC-DC Converter ModuleVicor Corporation
Vicor Corporation

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar