DataSheet.es    


PDF PCZ33742 Data sheet ( Hoja de datos )

Número de pieza PCZ33742
Descripción System Basis Chip
Fabricantes Freescale Semiconductor 
Logotipo Freescale Semiconductor Logotipo



Hay una vista previa y un enlace de descarga de PCZ33742 (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! PCZ33742 Hoja de datos, Descripción, Manual

www.DFaretaeSshceeatl4eUS.ceommiconductor
Advance Information
Document Number: MC33742
Rev. 10.0, 5/2007
System Basis Chip (SBC) with
Enhanced High-Speed CAN
Transceiver
33742
33742S
The 33742 and the 33742S are SPI-controlled System Basis Chips
(SBCs) combining many frequently used functions along with a CAN 2.0-
compliant transceiver, used in many automotive electronic control units
(ECUs). The 33742 SBC has a fully protected fixed 5.0 V low dropout
internal regulator with current limiting, overtemperature pre-warning, and
reset. A second 5.0 V regulator can be implemented using external pass
PNP bipolar junction pass transistor driven by the SBC’s external V2
sense input and V2 output drive pins.
The SBC has four main operating modes: Normal, Standby, Stop, and
Sleep mode. Additionally there is an internally switched high-side power
supply output, four wake-up inputs pins, a programmable window
watchdog, interrupt, reset, and a SPI module for communication and
control. The high-speed CAN A and B transceiver is available for inter-
module communication.
SYSTEM BASIS CHIP
DW SUFFIX
EG SUFFIX (PB-FREE)
98ASB42345B
28-PIN SOICW
EP SUFFIX
(PB-FREE)
98ARH99048A
48-PIN QFN
Features
• 1.0 Mbps CAN Transceiver Bus Interface with Bus Diagnostic
Capability
• SPI Control at Frequencies up to 4.0 Mhz
• 5.0 V Low Dropout Voltage Regulator with Current Limiting,
Overtemperature Pre-Warning, and Output Monitoring and Reset
• A Second 5.0 V Regulator Capability using an External Series Pass
Transistor
• Normal, Standby, Stop, and Sleep Modes of Operation with Low Sleep
and Stop Mode Current
• A High-Side (HS) Switch Output Driver for Controlling External
Circuitry.
• Pb-Free Packaging Designated by Suffix Code EG and EP
ORDERING INFORMATION
Device
MC33742DW/R2
Temperature
Range (TA)
MCZ33742EG/R2
MC33742SDW/R2 -40°C to 125°C
MCZ33742SEG/R2
Package
28 SOICW
PCZ33742EP/R2
48 QFN
VPWR
33742
5.0 V
VDD VSUP
V2
MCU
RST V2CTRL
V2
VPWR
CS
SCLK
MOSI
MISO
CS L0
SPI
SCLK
MOSI
L1
L2
MISO
L3
WDOG
INT HS
Safe Circuitry
ECU Local
Supply
TXD CANH
RXD CANL
Twisted CAN Bus
Pair
GND GND
Figure 1. 33742 Simplified Application Diagram
* This document contains certain information on a new product.
Specifications and information herein are subject to change without notice.
© Freescale Semiconductor, Inc., 2007. All rights reserved.

1 page




PCZ33742 pdf
PIN CONNECTIONS
NC 1
SCLK 2
MISO 3
MOSI 4
CS 5
WDOG 6
RXD 7
TXD 8
VDD 9
RST 10
INT 11
NC 12
36 NC
35 CANL
34 CANH
33 L3
32 L2
31 L1
30 L0
29 HS
28 VSUP
27 V2 CTRL
26 V2
25 NC
Figure 4. 33742 48-Pin Connections
Table 3. 33742 48-Pin Definitions
A functional description of each pin can be found in the Functional Pin description section beginning on page 22.
Pin Pin Name
Formal Name
Definition
1, 12-16,
21-25,
36-40,
45-48
2
3
NC
SCLK
MISO
No Connect
No connection.
Serial Data Clock
Master In Slave Out
Clock input pin for the Serial Peripheral Interface (SPI).
SPI data sent to the MCU by the 33742. When CS is HIGH, the pin is in the high-
impedance state.
4
MOSI
Master Out Slave In
SPI data received by the 33742.
5
6
7
8
9
10
11
17-20
41-44
CS
WDOG
RXD
TXD
VDD
RST
INT
GND
Chip Select
(Active LOW)
Watchdog Output
(Active LOW)
Receive Data
Transmit Data
Voltage Digital Drain
Reset Output
(Active LOW)
Interrupt Output
(Active LOW)
Ground
The CS input pin is used with the SPI bus to select the 33742. When the CS is asserted
LOW, the 33742 is the selected device of the SPI bus.
The WDOG output pin is asserted LOW if the software watchdog is not correctly
triggered.
CAN bus receive data output pin.
CAN bus transmit data input pin.
5.0 V regulator output pin. Supply pin for the MCU.
This is the device reset output pin whose main function is to reset the MCU. This pin has
an internal pullup current source to VDD.
This output is asserted LOW when an enabled interrupt condition occurs. The output is
a push-pull structure.
These device ground pins are internally connected to the package lead frame to provide
a 33742-to-PCB thermal path.
Analog Integrated Circuit Device Data
Freescale Semiconductor
33742
5

5 Page





PCZ33742 arduino
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 5. Static Electrical Characteristics (continued)
Characteristics noted under conditions 4.75 V V2 5.25 V, 5.5 V VSUP 18 V, and -40°C TA 125°C. Typical values
noted reflect the approximate parameter mean at TA = 25°C under nominal conditions unless otherwise noted.
Characteristic
Symbol Min Typ Max Unit
OUTPUT PIN (VDD) (CONTINUED) (18)
Temperature Threshold Difference
TSD - TPW
20
40 °C
Reset Threshold
Threshold 1, Default Value after Reset, RSTTH Bit Set to Logic [0]
Threshold 2, RSTTH Bit Set to Logic [1]
VRSTTH
V
4.5 4.6 4.7
4.0 4.2 4.3
VDD for Reset Active
Line Regulation (IDD = 10 mA, Capacitance = 47 µF Tantalum at VDD)
9.0 V < VSUP < 18 V
5.5 V < VSUP < 27 V
VDDR
VDDR
1.0
VRSTTH
V
mV
— 5.0 25
— 10 25
Load Regulation (Capacitance = 47 µF Tantalum at V1)
1.0 mA < IDD < 200 mA
VLD mV
— 25 75
Thermal Stability
VSUP = 13.5 V, IDD = 100 mA (19)
VTHERM-S
mV
— 30 50
OUTPUT PIN IN STOP MODE (VDD) (18)
VDD Output Voltage
IDD 2.0 mA
IDD 10 mA
VDDSTOP
V
4.75 5.0 5.25
4.75 5.0 5.25
IDD Output Current to Wake-Up
IDDS-WU
10
17
25 mA
Reset Threshold (18)
VRST-STOP
V
Threshold 1, Default Value after Reset, RSTTH Bit Set to Logic [0]
4.5 4.6 4.7
Threshold 2, RSTTH Bit Set to Logic [1]
4.1 4.2 4.3
Line Regulation (Capacitance = 47 µF Tantalum at VDD)
5.5 V < VSUP < 27 V, IDD = 2.0 mA
VLR-STOP
mV
— 5.0 25
Load Regulation (Capacitance = 47 µF Tantalum at V1)
1.0 mA < IDD < 10 mA
VLD-STOP
mV
— 15 75
Notes
18. IDD is the total regulator output current. VDD specification with external capacitor. Stability requirement: capacitance > 47 µF, ESR <
1.3 (tantalum capacitor). In Reset, Normal Request, Normal and Standby modes, measures with capacitance = 47 µF
tantalum.Selectable by RSTTH bit in SPI Register Reset Control Register (RCR).
19. Guaranteed by characterization and design; it is not production tested.
Analog Integrated Circuit Device Data
Freescale Semiconductor
33742
11

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet PCZ33742.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
PCZ33742System Basis ChipFreescale Semiconductor
Freescale Semiconductor

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar