DataSheet.es    


PDF AH115 Data sheet ( Hoja de datos )

Número de pieza AH115
Descripción High Linearity InGaP HBT Amplifier
Fabricantes WJ Communication 
Logotipo WJ Communication Logotipo



Hay una vista previa y un enlace de descarga de AH115 (archivo pdf) en la parte inferior de esta página.


Total 5 Páginas

No Preview Available ! AH115 Hoja de datos, Descripción, Manual

AH115www.DataSheet4U.com
½ Watt, High Linearity InGaP HBT Amplifier
The Communications Edge TM
Product Information
Product Features
x 1800 – 2300 MHz
x +28.5 dBm P1dB
x +44 dBm Output IP3
x 14 dB Gain @ 1960 MHz
x +5V Single Positive Supply
x MTTF > 100 Years
x Lead-free/green/RoHS-compliant
SOIC-8 SMT Pkg.
Applications
x Final stage amplifiers for Repeaters
x Mobile Infrastructure
Product Description
Functional Diagram
The AH115 is a high dynamic range driver amplifier in a
low-cost surface mount package. The InGaP/GaAs HBT is
able to achieve high performance for various narrow-band
tuned application circuits with up to +44 dBm OIP3 and
+28.5 dBm of compressed 1-dB power. All devices are
100% RF and DC tested. The AH115 is available in lead-
free/green/RoHS-compliant SOIC-8 package.
The product is targeted for use as driver amplifiers for
wireless infrastructure where high linearity and medium
power is required. The internal active bias allows the
AH115 to maintain high linearity over temperature and
operate directly off a +5 V supply. This combination
makes the device an excellent fit for transceiver line
cards and power amplifiers in current and next generation
multi-carrier 3G base stations.
18
27
36
45
Function
Vref
Input
Output
Vbias
GND
N/C or GND
Pin No.
1
3
6, 7
8
Backside Paddle
2, 4, 5
Specifications (1)
Parameters
Operational Bandwidth
Test Frequency
Gain
Input Return Loss
Output Return Loss
Output P1dB
Output IP3 (2)
IS-95A Channel Power
@ -45 dBc ACPR, 1960 MHz
wCDMA Channel Power
@ -45 dBc ACLR, 2140 MHz
Noise Figure
Operating Current Range (3)
Device Voltage
Units
MHz
MHz
dB
dB
dB
dBm
dBm
dBm
Min
1800
12.5
+26.5
+41
dBm
dB
mA 200
V
Typ
2140
14.4
23
8
+28.5
+42
+22.5
+20
5.3
250
+5
Max
2300
300
1. Test conditions unless otherwise noted. 25 ºC, Vsupply = +5 V in tuned application circuit.
2. 3OIP measured with two tones at an output power of +11 dBm/tone separated by 1 MHz. The
suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule.
3. This corresponds to the quiescent current or operating current under small-signal conditions. It is
expected that the current can increase up to 300mA at P1dB.
Typical Performance (4)
Parameters
Frequency
Gain
S11
S22
Output P1dB
Output IP3 (2)
IS-95A Channel Power
@ -45 dBc ACPR,
wCDMA Channel Power
@ -45 dBc ACLR
Noise Figure
Supply Bias
Units
MHz
dB
dB
dB
dBm
dBm
dBm
dBm
dB
Typical
1960
2140
14.3 14.4
-12 -23
-8 -8
+28.3
+28.5
+44 +42
+22.5
+20
5 5.3
+5 V @ 250 mA
4. Typical parameters reflect performance in a tuned application circuit at +25 ¡ C.
Absolute Maximum Rating
Parameter
Rating
Operating Case Temperature
-40 to +85 qC
Storage Temperature
-65 to +150 qC
RF Input Power (continuous)
+22 dBm
Device Voltage
+8 V
Device Current
400 mA
Device Power
2W
Junction Temperature
+250 qC
Operation of this device above any of these parameters may cause permanent damage.
Ordering Information
Part No.
AH115-S8G
AH115-S8PCB1960
AH115-S8PCB2140
Description
½ Watt, High Linearity InGaP HBT Amplifier
(lead-free/green/RoHS-compliant SOIC-8 Pkg)
1960 MHz Evaluation Board
2140 MHz Evaluation Board
Specifications and information are subject to change without notice
WJ Communications, Inc   Phone 1-800-WJ1-4401   FAX: 408-577-6621   e-mail: [email protected]   Web site: www.wj.com
Page 1 of 5 April 2006

1 page




AH115 pdf
AH115www.DataSheet4U.com
½ Watt, High Linearity InGaP HBT Amplifier
The Communications Edge TM
Product Information
AH115-S8G (Green / Lead-free SOIC-8 Package) Mechanical Information
This package is lead-free/Green/RoHS-compliant. It is compatible with both lead-free (maximum 260 qC reflow temperature) and leaded
(maximum 245 qC reflow temperature) soldering processes. The plating material on the leads is NiPdAu.
Outline Drawing
Product Marking
The component will be marked with an
“AH115G” designator with an alphanumeric lot
code on the top surface of the package. The
obsolete tin-lead package is marked with an
“AH115-S8” or “ECP050G” designator
followed by an alphanumeric lot code.
Tape and reel specifications for this part are
located on the website in the “Application
Notes” section.
ESD / MSL Information
Land Pattern
ESD Rating:
Value:
Test:
Standard:
Class 1B
Passes ¨ 500V to <1000V
Human Body Model (HBM)
JEDEC Standard JESD22-A114
MSL Rating: Level 2 at +260 C convection reflow
©
Standard: JEDEC Standard J-STD-020
Mounting Config. Notes
1. Ground / thermal vias are critical for the proper performance of this
device. Vias should use a .35mm (#80 / .0135” ) diameter drill and
have a final plated thru diameter of .25 mm (.010” ).
2. Add as much copper as possible to inner and outer layers near the
part to ensure optimal thermal performance.
3. Mounting screws can be added near the part to fasten the board to a
heatsink. Ensure that the ground / thermal via region contacts the
heatsink.
4. Do not put solder mask on the backside of the PC board in the
region where the board contacts the heatsink.
5. RF trace width depends upon the PC board material and
construction.
6. Use 1 oz. Copper minimum.
7. All dimensions are in millimeters (inches). Angles are in degrees.
Thermal Specifications
Parameter
Rating
Operating Case Temperature (1) -40 to +85 qC
Thermal Resistance (2), Rth
62 qC / W
Junction Temperature (3), Tjc
162 qC
Notes:
1. The amplifier can be operated at 105 § C case temperature for up to 1000
hours over its lifetime without degradation in performance and will not
degrade device operation at the recommended maximum 85 C§ case
temperature for the rest of its lifetime.
2. The thermal resistance is referenced from the junction-to-case at a case
temperature of 85 § C. Tjc is a function of the voltage at pins 6 and 7 and
the current applied to pins 6, 7, and 8 and can be calculated by:
Tjc = Tcase + Rth * Vcc * Icc
3. This corresponds to the typical biasing condition of +5V, 250 mA at an
85§ C case temperature. A minimum MTTF of 1 million hours is achieved
for junction temperatures below 247 § C.
100000
MTTF vs. GND Tab Temperature
10000
1000
100
60
70 80 90 100 110
Tab Temperature (°C)
120
Specifications and information are subject to change without notice
WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: [email protected] Web site: www.wj.com
¦
¦¦
¦
Page 5 of 5 April 2006

5 Page










PáginasTotal 5 Páginas
PDF Descargar[ Datasheet AH115.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
AH11High Dynamic Range Dual AmplifierWJ Communication
WJ Communication
AH11High Dynamic Range Dual AmplifierTriQuint Semiconductor
TriQuint Semiconductor
AH110High Linearity InGaP HBT AmplifierWJ Communication
WJ Communication
AH114High Linearity InGaP HBT AmplifierWJ Communication
WJ Communication

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar