DataSheet.es    


PDF XP1015 Data sheet ( Hoja de datos )

Número de pieza XP1015
Descripción GaAs MMIC Power Amplifier
Fabricantes Mimix Broadband 
Logotipo Mimix Broadband Logotipo



Hay una vista previa y un enlace de descarga de XP1015 (archivo pdf) en la parte inferior de esta página.


Total 5 Páginas

No Preview Available ! XP1015 Hoja de datos, Descripción, Manual

43.5-46.5 GHz GaAs MMIC
Power Amplifier
May 2005 - Rev 20-May-05
P1015
Features
Excellent Saturated Output Stage
Balanced Design Provides Good Input/Output Match
13.0 dB Small Signal Gain
+31.0 dBm P1dB Compression Point
100% On-Wafer RF, DC and Output Power Testing
100% Visual Inspection to MIL-STD-883
Method 2010
Chip Device Layout
General Description
Mimix Broadband's three stage balanced 43.5 - 46.5
GHz GaAs MMIC power amplifier has a small signal
gain of 13.0 dB with a +31.0 dBm P1dB output
compression point.The device also includes Lange
couplers to achieve good input and output return
loss.This MMIC uses Mimix Broadbands 0.15 µm GaAs
PHEMT device model technology, and is based upon
electron beam lithography to ensure high
repeatability and uniformity.The chip has surface
passivation to protect and provide a rugged part with
www.DataSheet4U.combackside via holes and gold metallization to allow
either a conductive epoxy or eutectic solder die
attach process.This device is well suited for
Millimeter-wave Point-to-Point Radio, LMDS, SATCOM
and VSAT applications.
Absolute Maximum Ratings
Supply Voltage (Vd)
Supply Current (Id1,2,3)
Gate Bias Voltage (Vg)
Input Power (Pin)
Storage Temperature (Tstg)
Operating Temperature (Ta)
Channel Temperature (Tch)
+6.0 VDC
945,945,1915 mA
+0.3 VDC
+26 dBm
-65 to +165 OC
-55 to MTTF Table1
MTTF Table1
(1) Channel temperature affects a device's MTTF. It is
recommended to keep channel temperature as low as
possible for maximum life.
Electrical Characteristics (Ambient Temperature T = 25 oC)
Parameter
Frequency Range (f )
Input Return Loss (S11)
Output Return Loss (S22)
Small Signal Gain (S21)
Gain Flatness (S21)
Reverse Isolation (S12)
Output Power for 1dB Compression (P1dB)2
Drain Bias Voltage (Vd1,2,3)
Gate Bias Voltage (Vg1,2,3)
Supply Current (Id1) (Vd=5.0V, Vg=-0.5V Typical)
Supply Current (Id2) (Vd=5.0V, Vg=-0.5V Typical)
Supply Current (Id3) (Vd=5.0V, Vg=-0.5V Typical)
Units Min. Typ. Max.
GHz 43.5 - 46.5
dB - 20.0 -
dB - 20.0 -
dB - 13.0 -
dB - +/-1.0 -
dB - 45.0 -
dBm - +31.0 -
VDC - +5.0 +5.5
VDC -1.0 -0.5 0.0
mA - 720 860
mA - 720 860
mA - 1440 1740
(2) Measured using constant current.
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 1 of 5
Characteristic Data and Specifications are subject to change without notice. ©2005 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.

1 page




XP1015 pdf
43.5-46.5 GHz GaAs MMIC
Power Amplifier
May 2005 - Rev 20-May-05
P1015
Handling and Assembly Information
CAUTION! - Mimix Broadband MMIC Products contain gallium arsenide (GaAs) which can be hazardous to the
human body and the environment. For safety, observe the following procedures:
Do not ingest.
Do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical
processing as these by-products are dangerous to the human body if inhaled, ingested, or swallowed.
Observe government laws and company regulations when discarding this product.This product must be
discarded in accordance with methods specified by applicable hazardous waste procedures.
Life Support Policy - Mimix Broadband's products are not authorized for use as critical components in life support
devices or systems without the express written approval of the President and General Counsel of Mimix
Broadband. As used herein: (1) Life support devices or systems are devices or systems which, (a) are intended for
surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in
accordance with instructions for use provided in the labeling, can be reasonably expected to result in a
significant injury to the user. (2) A critical component is any component of a life support device or system whose
failure to perform can be reasonably expected to cause the failure of the life support device or system, or to
affect its safety or effectiveness.
ESD - Gallium Arsenide (GaAs) devices are susceptible to electrostatic and mechanical damage. Die are supplied
in antistatic containers, which should be opened in cleanroom conditions at an appropriately grounded anti-
static workstation. Devices need careful handling using correctly designed collets, vacuum pickups or, with care,
sharp tweezers.
Die Attachment - GaAs Products from Mimix Broadband are 0.100 mm (0.004") thick and have vias through to the
backside to enable grounding to the circuit. Microstrip substrates should be brought as close to the die as
possible.The mounting surface should be clean and flat. If using conductive epoxy, recommended epoxies are
Ablestick 84-1LMI or 84-1LMIT cured in a nitrogen atmosphere per manufacturer's cure schedule. Apply epoxy
sparingly to avoid getting any on to the top surface of the die. An epoxy fillet should be visible around the total
die periphery. If eutectic mounting is preferred, then a fluxless gold-tin (AuSn) preform, approximately 0.0012
thick, placed between the die and the attachment surface should be used. A die bonder that utilizes a heated
collet and provides scrubbing action to ensure total wetting to prevent void formation in a nitrogen atmosphere
is recommended.The gold-tin eutectic (80% Au 20% Sn) has a melting point of approximately 280 C (Note: Gold
Germanium should be avoided).The work station temperature should be 310 C+- 10 C. Exposure to these
extreme temperatures should be kept to minimum.The collet should be heated, and the die pre-heated to avoid
excessive thermal shock. Avoidance of air bridges and force impact are critical during placement.
Wire Bonding - Windows in the surface passivation above the bond pads are provided to allow wire bonding to
the die's gold bond pads.The recommended wire bonding procedure uses 0.076 mm x 0.013 mm (0.003" x
0.0005") 99.99% pure gold ribbon with 0.5-2% elongation to minimize RF port bond inductance. Gold 0.025 mm
(0.001") diameter wedge or ball bonds are acceptable for DC Bias connections. Aluminum wire should be
avoided.Thermo-compression bonding is recommended though thermosonic bonding may be used providing
the ultrasonic content of the bond is minimized. Bond force, time and ultrasonics are all critical parameters.
Bonds should be made from the bond pads on the die to the package or substrate. All bonds should be as short
as possible.
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 5 of 5
Characteristic Data and Specifications are subject to change without notice. ©2005 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.

5 Page










PáginasTotal 5 Páginas
PDF Descargar[ Datasheet XP1015.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
XP1010GaAs MMIC Power AmplifierMimix Broadband
Mimix Broadband
XP1011GaAs MMIC Power AmplifierMimix Broadband
Mimix Broadband
XP1012GaAs MMIC Power AmplifierMimix Broadband
Mimix Broadband
XP1013GaAs MMIC Power AmplifierMimix Broadband
Mimix Broadband

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar