DataSheet.es    


PDF ICM7243 Data sheet ( Hoja de datos )

Número de pieza ICM7243
Descripción LED Display Decoder Driver
Fabricantes Intersil Corporation 
Logotipo Intersil Corporation Logotipo



Hay una vista previa y un enlace de descarga de ICM7243 (archivo pdf) en la parte inferior de esta página.


Total 12 Páginas

No Preview Available ! ICM7243 Hoja de datos, Descripción, Manual

ICM7243
August 1997
8-Character, Microprocessor-
Compatible, LED Display Decoder Driver
Features
Description
• 14-Segment and 16-Segment Fonts with Decimal Point
• Mask Programmable for Other Font-Sets Up to 64
Characters
• Microprocessor Compatible
• Directly Drives LED Common Cathode Displays
• Cascadable Without Additional Hardware
• Standby Feature Turns Display Off; Puts Chip in Low
Power Mode
• Sequential Entry or Random Entry of Data Into
Display
• Single +5V Operation
• Character and Segment Drivers, All MUX Scan
Circuitry, 8 x 6 Static Memory and 64-Character ASCll
Font Generator Included On-Chip
Ordering Information
PART NUMBER
ICM7243AIJL
ICM7243AIPL
ICM7243BIJL
TEMP.
RANGE (oC)
PACKAGE
-25oC to 85 40 Ld CERPDIP
-25oC to 85 40 Ld PDIP
-25oC to 85 40 Ld CERPDIP
PKG.
NO.
F40.6
E40.6
F40.6
The ICM7243 is an 8-character, alphanumeric display driver
and controller which provides all the circuitry required to
interface a microprocessor or digital system to a 14-segment
or 16-segment display. It is primarily intended for use in
microprocessor systems, where it minimizes hardware and
software overhead. Incorporated on-chip are a 64-character
ASClI decoder, 8 x 6 memory, high power character and
segment drivers, and the multiplex scan circuitry.
6-bit ASCll data to be displayed is written into the memory
directly from the microprocessor data bus. Data location
depends upon the selection of either Sequential
(MODE = 1) or Random access mode (MODE = 0). In the
Sequential Access mode the first entry is stored in the
lowest location and displayed in the “left-most” character
position. Each subsequent entry is automatically stored in
the next higher location and displayed to the immediate
“right” of the previous entry. A DISPlay FULL signal is pro-
vided after 8 entries; this signal can be used for cascading
devices together. A CLeaR pin is provided to clear the mem-
ory and reset the location counter. The Random Access
mode allows the processor to select the memory address
and display digit for each input word.
The character multiplex scan runs whenever data is not
being entered. It scans the memory and CHARacter drivers,
and ensures that the decoding from memory to display is
done in the proper sequence. Intercharacter blanking is
provided to avoid display ghosting.
ICM7243BlPL
-25 to 85 40 Ld PDIP
E40.6
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
9-21
File Number 3162.1

1 page




ICM7243 pdf
Timing Waveforms
WR
CLEAR
ICM7243
CS
CS
ADDRESS
WRITE
DATA
tCS
tAH
tAS
VALID
tWC
tWPI
tWHP
tDS tT
tT tDH
VALID
FIGURE 1. RANDOM ACCESS TIMING
CHAR
1
CHAR
2
tSEN
CHAR
8
tWPH
SEN
DISPLAY FULL
tWDF
INTERNAL
INTER-CHARACTER
BLANKING
SIGNAL
CHAR 1
CHAR 2
CHAR 3
CHARACTERS
DRIVE
SIGNALS
CHAR 4
CHAR 5
CHAR 6
CHAR 7
CHAR 8
FIGURE 2. SEQUENTIAL ACCESS MODE TIMING (MODE = 1)
~5µs
~300µs
INTER-CHARACTER BLANKING
FIGURE 3. DISPLAY CHARACTERS MULTIPLEX TIMING DIAGRAM
9-25

5 Page





ICM7243 arduino
ICM7243
Display Font and Segment Assignments (Continued)
00
a1 a a2
f hi j b
g1 g2
eml k c
d2 d d1
DP
01
D5, D4 1 0
11
D3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
D2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1
D1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1
D0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
NOTE: Segments a and d appear as 2 segments each, but both halves are driven together.
FIGURE 12. ICM7243B 14-SEGMENT CHARACTER FONT WITH DECIMAL POINT
SEGMENT
DRIVER
VDD
VLED = 1.6V
RTYPICAL = 100µ
R
SEG x DISPLAY
CHARACTER
DRIVER
RDS(ON) ~ 4
CHAR N
VSS
SEGMENT LEDs
FIGURE 13. SEGMENT AND CHARACTER DRIVERS OUTPUT CIRCUIT
9-31

11 Page







PáginasTotal 12 Páginas
PDF Descargar[ Datasheet ICM7243.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
ICM7240(ICM7240 - ICM7260) Fixed And Programmable Timer/CountersMaxim Integrated Products
Maxim Integrated Products
ICM7242Long Range Fixed TimerIntersil Corporation
Intersil Corporation
ICM7242(ICM7240 - ICM7260) Fixed And Programmable Timer/CountersMaxim Integrated Products
Maxim Integrated Products
ICM7243LED Display Decoder DriverIntersil Corporation
Intersil Corporation

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar