DataSheet.es    


PDF 225P Data sheet ( Hoja de datos )

Número de pieza 225P
Descripción Polyester Capacitors
Fabricantes Vishay Siliconix 
Logotipo Vishay Siliconix Logotipo



Hay una vista previa y un enlace de descarga de 225P (archivo pdf) en la parte inferior de esta página.


Total 5 Páginas

No Preview Available ! 225P Hoja de datos, Descripción, Manual

Type 225P
Vishay Sprague
Polyester Capacitors
Filmite® “E”, ORANGE DROP®, Radial Lead
PERFORMANCE CHARACTERISTICS
FEATURES
Utilizes minimum area where printed wiring
board space is most important
Wound from PETP polyester film and thin gauge RoHS
foil under carefully controlled atmospheric COMPLIANT
conditions
Protected against moisture by a conformal coating of
epoxy
Specifically designed for printed wiring board applications
Widely used in computers, instrumentation and
telecommunications equipment
100 VDC through 600 VDC, may be operated up to
+ 125 °C with proper dearting
Operating Temperature: - 55 °C to + 85 °C
Dielectric Withstanding Voltage:
To + 105 °C when working voltage is reduced to 70 % of
Capacitors shall withstand a DC potential of 250 % of rated
+ 85 °C rating; to + 125 °C when working voltage is reduced
voltage applied between terminals for not more than 5
to 50 % of 85 °C rating
seconds. The test voltage must be applied and discharged
Insulation Resistance: After a 2 minute charge at rated
through a resistor of 1 ohm per volt.
voltage or 500 V, whichever is less.
Humidity Test:
At + 25 °C: 100 000 Megohm for C 0.25 Microfarads
Condition capacitors with no voltage applied for 72 hours at
25000 Megohm - Microfarads for C > 0.25 Microfarads
95 % relative humidity and + 75 °C. Remove capacitors from
At + 85 °C: 10 000 Megohm for C 0.15 Microfarads
humidity chamber, wipe surface dry of moisture and dry in
1500 Megohm - Microfarads for C > 0.15 Microfarads www.DataSheet4U.ccomirculating air for 4 hours. Measure insulation resistance after
At + 105 °C: 1500 Megohm for C 0.17 Microfarads
a 2 minute charge at 25 °C and rated voltage or 500 VDC,
250 Megohm - Microfarads for C > 0.17 Microfarads
whichever is less. Minimum product of insulation resistance
At + 125 °C: 200 Megohm for C 0.13 Microfarads
and capacitance shall be 5000 Megohm - Microfarads after
25 Megohm - Microfarads for C > 0.13 Microfarads
test but need not exceed 10 000 Megohm. Not more than
one failure allowed in 12 units tested.
Capacitance Tolerance and Dissipation Factor:
Capacitors shall be measured at a frequency of 1000 Hz at
+ 25 °C or else be referred to measurements made at that
frequency and temperature. The maximum dissipation factor
shall be 0.75 %
DC Life Test:
Capacitance are capable of withstanding a 500 hour life test
at + 85 °C at 150 % of rated working voltage. After test,
capacitance shall not have changed by more than 5 % of
initial value, insulation resistance shall not have decreased
by more than 50 % of the initial limit and dissipation factor
shall not have increased to more than 1 %.
DIMENSIONS in inches [millimeters]
L
Max.
L
Max.
Lead
Length
0.237"
[6.020]
Max.
Lead
Length
0.237
[6.020]
Max.
H
Max.
L
Max.
Lead
Length
0.237
[6.020]
Max.
T Max.
S
± 0.060 [1.524]
Terminal A
CASE
CODE
W
X
Y
Document Number: 42016
Revision: 19-Feb-07
S
± 0.030 [0.762]
Terminal B
L
(Max.)
0.70 [17.78]
0.80 [20.32]
1.25 [31.75]
S
± 0.030 [0.762]
Terminal D
Tinned Copper-Clad Steel
0.032 [0.813] Dia.
(No. 20 AWG)
Terminal A and B
0.562 [14.275]
0.613 [15.570]
0.969 [24.613]
S
Terminal D
0.375 [9.525]
0.375 [9.525]
0.719 [18.263]
For technical questions, contact: [email protected]
www.vishay.com
25

1 page




225P pdf
Notice
Legal Disclaimer Notice
Vishay
Specifications of the products displayed herein are subject to change without notice. Vishay Intertechnology, Inc.,
or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies.
Information contained herein is intended to provide a product description only. No license, express or implied, by
estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Vishay's
terms and conditions of sale for such products, Vishay assumes no liability whatsoever, and disclaims any express
or implied warranty, relating to sale and/or use of Vishay products including liability or warranties relating to fitness
for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications.
Customers using or selling these products for use in such applications do so at their own risk and agree to fully
indemnify Vishay for any damages resulting from such improper use or sale.
Document Number: 91000
Revision: 08-Apr-05
www.vishay.com
1

5 Page










PáginasTotal 5 Páginas
PDF Descargar[ Datasheet 225P.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
2250-XC6DT2DIESEL ENGINE-GENERATOR SETMTU Onsite Energy
MTU Onsite Energy
225CNQSchottky Rectifier ( Diode )International Rectifier
International Rectifier
225PPolyester CapacitorsVishay Siliconix
Vishay Siliconix

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar