DataSheet.es    


PDF CAT3644 Data sheet ( Hoja de datos )

Número de pieza CAT3644
Descripción 4-Channel Ultra High Efficiency Quad-Mode TM LED Driver
Fabricantes Catalyst Semiconductor 
Logotipo Catalyst Semiconductor Logotipo



Hay una vista previa y un enlace de descarga de CAT3644 (archivo pdf) en la parte inferior de esta página.


Total 14 Páginas

No Preview Available ! CAT3644 Hoja de datos, Descripción, Manual

CAT3644
4-Channel Ultra High Efficiency Quad-Mode™
LED Driver
FEATURES
DESCRIPTION
„ High efficiency 1.33x charge pump
The CAT3644 is a high efficiency quad-mode
„ Quad-mode charge pump: 1x, 1.33x, 1.5x, 2x
„ Drives up to 4 LEDs at 25mA each
fractional charge pump that can drive up to four LEDs
programmable by a one wire digital interface. The
inclusion of a 1.33x fractional charge pump mode
„ 1-wire EZDim™ LED current programming
increases device efficiency by up to 10% over tradi–
„ Power efficiency up to 92%
„ Low noise input ripple in all modes
„ “Zero” current shutdown mode
„ Soft start and current limiting
tional 1.5x charge pumps with no added external
capacitors.
Low noise input ripple is achieved by operating at a
constant switching frequency which allows the use of
small external ceramic capacitors. The multi-fractional
„ Short circuit protection
„ Thermal shutdown protection
charge pump supports a wide range of input voltages
from 2.5V to 5.5V.
„ 3mm x 3mm, 16-lead TQFN package
The EN/DIM logic input functions as a chip enable and
a digital dimming interface for current setting of all
APPLICATION
LEDs. Six different current ratios are available via the
interface.
„ LCD Display Backlight
„ Cellular Phones
The device is available in the tiny 16-lead TQFN
3mmwww.DataSheet4U.com x 3mm package with a max height of 0.8mm.
„ Digital Still Cameras
„ Handheld Devices
The 1.33x charge pump with two fly capacitors is a
patent pending architecture exclusive to Catalyst
Semiconductor.
ORDERING INFORMATION
Part
Number
Package
CAT3644HV3-T2 TQFN-16 3x3mm(1)
Package
Marking
JAAG
For Ordering Information details, see page 13.
Note: (1) Matte-Tin Plated Finish (RoHS-compliant)
PIN CONFIGURATION
TYPICAL APPLICATION CIRCUIT
1µF 1µF
16 15 14 13
LED2
LED3
LED4
RSET
1
2
3
4
12 C2-
11 C2+
10 C1-
9 C1+
5678
VIN
2.4V CIN
to
5.5V 1µF
1-Wire
EZDimTM
Programming
3.8k
C1+
VIN
C1- C2+
C2-
VOUT
CAT3644
EN/DIM
RSET
GND
LED1
LED2
LED3
LED4
White LEDs
VOUT
COUT
1µF
20mA
© 2007 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
1
Doc. No. 5023, Rev. B

1 page




CAT3644 pdf
CAT3644
TYPICAL PERFORMANCE CHARACTERISTICS
VIN = 3.6V, IOUT = 80mA (4 LEDs at 20mA), CIN = COUT = C1 = C2 = 1μF, TAMB = 25°C unless otherwise specified.
Switching Frequency vs. Temperature
1.3
1.2
1.5x Mode
1.1
1.0
0.9 1.33x, 2x Mode
0.8
0.7
-40
0 40 80
TEMPERATURE [°C]
120
Output Resistance vs. Input Voltage
12
10 2x
8
6
1.5x
4
1.33x
2 1x
0
2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
INPUT VOLTAGE [V]
Power Up in 1x Mode
Power Up in 1.33x Mode
Power Up in 1.5x Mode
Power Up in 2x Mode
© 2007 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
5
Doc. No. 5023, Rev. B

5 Page





CAT3644 arduino
CAT3644
Unused LED Channels
For applications not requiring all the channels, it is
recommended the unused LED pins be tied directly to
VOUT (see Figure 4).
1µF 1µF
VIN
CIN
1µF
ENABLE
DIMMING
RSET
C1+
VIN
C1- C2+
C2-
VOUT
CAT3644
EN/DIM
RSET
GND
LED1
LED2
LED3
LED4
COUT
1µF
Figure 4. Application with 3 LEDs
Protection Mode
If an LED is disconnected, the driver senses that and
automatically ignores that channel. When all LEDs are
disconnected, the driver goes to 1x mode where the
output is equal to the input voltage.
As soon as the output exceeds about 6V, the driver
resets itself and reevaluate the mode.
External Components
The driver requires four external 1μF ceramic capa-
citors for decoupling input, output, and for the charge
pump. Both capacitors type X5R and X7R are
recommended for the LED driver application. In all
charge pump modes, the input current ripple is kept
very low by design and an input bypass capacitor of
1μF is sufficient.
In 1x mode, the device operates in linear mode and
does not introduce switching noise back onto the
supply.
Recommended Layout
In charge pump mode, the driver switches internally at
a high frequency. It is recommended to minimize trace
length to all four capacitors. A ground plane should
cover the area under the driver IC as well as the
bypass capacitors. Short connection to ground on
capacitors CIN and COUT can be implemented with the
use of multiple via. A copper area matching the TQFN
exposed pad (TAB) must be connected to the ground
plane underneath. The use of multiple via improves
the package heat dissipation.
GND
If the die temperature exceeds +150°C, the driver will
enter a thermal protection shutdown mode. When the
device temperature drops by about 20°C, the device
will resume normal operation.
Pin1
C2
LED Selection
LEDs with forward voltages (VF) ranging from 1.3V to
4.3V may be used. Selecting LEDs with lower VF is
recommended in order to improve the efficiency by
keeping the driver in 1x mode longer as the battery
voltage decreases.
For example, if a white LED with a VF of 3.3V is
selected over one with VF of 3.5V, the driver will stay
in 1x mode for lower supply voltage of 0.2V. This
helps improve the efficiency and extends battery life.
RSET
EN/DIM
GND
COUT
CIN
GND
Figure 5. Recommended Layout
C1
VIN
© 2007 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
11
Doc. No. 5023, Rev. B

11 Page







PáginasTotal 14 Páginas
PDF Descargar[ Datasheet CAT3644.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
CAT36433-Channel Ultra High Efficiency Quad-Mode TM LED DriverCatalyst Semiconductor
Catalyst Semiconductor
CAT36433-Channel Ultra High Efficiency LED DriverON Semiconductor
ON Semiconductor
CAT36444-Channel Ultra High Efficiency Quad-Mode TM LED DriverCatalyst Semiconductor
Catalyst Semiconductor
CAT36444-Channel Ultra High Efficiency LED DriverON Semiconductor
ON Semiconductor

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar