DataSheet.es    


PDF 2N6394 Data sheet ( Hoja de datos )

Número de pieza 2N6394
Descripción (2N6394 - 2N6399) Silicon Controlled Rectifiers
Fabricantes ON Semiconductor 
Logotipo ON Semiconductor Logotipo



Hay una vista previa y un enlace de descarga de 2N6394 (archivo pdf) en la parte inferior de esta página.


Total 5 Páginas

No Preview Available ! 2N6394 Hoja de datos, Descripción, Manual

www.DataSheet4U.com
2N6394 Series
Preferred Device
Silicon Controlled Rectifiers
Reverse Blocking Thyristors
Designed primarily for half-wave ac control applications, such as
motor controls, heating controls and power supplies.
Features
Glass Passivated Junctions with Center Gate Geometry for Greater
Parameter Uniformity and Stability
Small, Rugged, Thermowatt Construction for Low Thermal
Resistance, High Heat Dissipation and Durability
Blocking Voltage to 800 V
Pb−Free Packages are Available*
MAXIMUM RATINGS † (TJ = 25°C unless otherwise noted)
Rating
Symbol Value
Peak Repetitive Off−State Voltage (Note 1)
(TJ = −40 to 125°C, Sine Wave,
50 to 60 Hz, Gate Open)
2N6394
2N6395
2N6397
2N6399
VDRM,
VRRM
50
100
400
800
Unit
V
On-State RMS Current
(180° Conduction Angles; TC = 90°C)
Peak Non-Repetitive Surge Current
(1/2 Cycle, Sine Wave, 60 Hz, TJ = 90°C)
Circuit Fusing (t = 8.3 ms)
IT(RMS)
ITSM
I2t
12
100
40
A
A
A2s
Forward Peak Gate Power
(Pulse Width 1.0 ms, TC = 90°C)
PGM
20
W
Forward Average Gate Power
(t = 8.3 ms, TC = 90°C)
PG(AV)
0.5
W
Forward Peak Gate Current
(Pulse Width 1.0 ms, TC = 90°C)
IGM 2.0 A
Operating Junction Temperature Range
TJ −40 to +125 °C
Storage Temperature Range
Tstg −40 to +150
MAXIMUM RATINGS † (TJ = 25°C unless otherwise noted)
°C
Rating
Symbol
Max
Unit
Thermal Resistance, Junction−to−Case
Maximum Lead Temperature for Soldering
Purposes 1/8from Case for 10 Seconds
RqJC
TL
2.0 °C/W
260 °C
†Indicates JEDEC Registered Data
Stresses exceeding Maximum Ratings may damage the device. Maximum
Ratings are stress ratings only. Functional operation above the Recommended
Operating Conditions is not implied. Extended exposure to stresses above the
Recommended Operating Conditions may affect device reliability.
1. VDRM and VRRM for all types can be applied on a continuous basis. Ratings
apply for zero or negative gate voltage; however, positive gate voltage shall
not be applied concurrent with negative potential on the anode. Blocking
voltages shall not be tested with a constant current source such that the
voltage ratings of the devices are exceeded.
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
© Semiconductor Components Industries, LLC, 2006
August, 2006 − Rev. 6
1
http://onsemi.com
SCRs
12 AMPERES RMS
50 thru 800 VOLTS
G
AK
MARKING
DIAGRAM
4
TO−220AB
CASE 221A
STYLE 3
2N639xG
AYWW
1
2
3
2N639x = Device Code
x = 4, 5, 7, or 9
G = Pb−Free Package
A = Assembly Location
Y = Year
WW = Work Week
PIN ASSIGNMENT
1 Cathode
2 Anode
3 Gate
4 Anode
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 4 of this data sheet.
Preferred devices are recommended choices for future use
and best overall value.
Publication Order Number:
2N6394/D

1 page




2N6394 pdf
2N6394 Series
PACKAGE DIMENSIONS
TO−220AB
CASE 221A−09
ISSUE AD
BF
Q
H
Z
4
1 23
A
K
L
V
G
N
D
−T−
SEATING
PLANE
C
TS
U
R
J
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION Z DEFINES A ZONE WHERE ALL
BODY AND LEAD IRREGULARITIES ARE
ALLOWED.
INCHES
DIM MIN MAX
A 0.570 0.620
B 0.380 0.405
C 0.160 0.190
D 0.025 0.035
F 0.142 0.147
G 0.095 0.105
H 0.110 0.155
J 0.018 0.025
K 0.500 0.562
L 0.045 0.060
N 0.190 0.210
Q 0.100 0.120
R 0.080 0.110
S 0.045 0.055
T 0.235 0.255
U 0.000 0.050
V 0.045 −−−
Z −−− 0.080
STYLE 3:
PIN 1. CATHODE
2. ANODE
3. GATE
4. ANODE
MILLIMETERS
MIN MAX
14.48 15.75
9.66 10.28
4.07 4.82
0.64 0.88
3.61 3.73
2.42 2.66
2.80 3.93
0.46 0.64
12.70 14.27
1.15 1.52
4.83 5.33
2.54 3.04
2.04 2.79
1.15 1.39
5.97 6.47
0.00 1.27
1.15 −−−
−−− 2.04
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
http://onsemi.com
5
2N6394/D

5 Page










PáginasTotal 5 Páginas
PDF Descargar[ Datasheet 2N6394.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
2N6394SCRs 12 AMPERES RMS 50 thru 800 VOLTSMotorola  Inc
Motorola Inc
2N6394(2N6394 - 2N6399) Silicon Controlled RectifiersON Semiconductor
ON Semiconductor
2N6394Thyristor SCR 50V 100A 3-Pin(3+Tab) TO-220AB BulkNew Jersey Semiconductor
New Jersey Semiconductor
2N6394SILICON CONTROLLED RECTIFIERSDigitron Semiconductors
Digitron Semiconductors

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar