|
|
PDF TD352 Data sheet ( Hoja de datos )
| Número de pieza | TD352 | |
| Descripción | Advanced IGBT/MOSFET Driver | |
| Fabricantes | ST Microelectronics | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TD352 (archivo pdf) en la parte inferior de esta página. Total 13 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
TD352
Advanced IGBT/MOSFET Driver
■ 1A sink / 0.75A source min. gate drive
■ Active Miller clamp feature
■ Desaturation detection
■ Adjustable and accurate turn-on delay
■ UVLO protection
■ 2kV ESD protection
Description
TD352 is an advanced gate driver for IGBT and
power MOSFET. Control and protection functions
are included and allow the design of high reliability
systems.
Innovative active Miller clamp function avoids the
need of negative gate drive in most applications
and allows the use of a simple bootstrap supply
for the high side driver.
TD352 includes an adjustable turn-on delay. This
feature can be used to implement reliable
deadtime between high and low sides of a half
bridge. External resistor and capacitor are used to
provide accurate timing.
Applications
■ 1200V 3-phase inverter
■ Motor control systems
■ UPS
N
DIP-8
(Plastic Package)
D
SO-8
(Plastic Micropackage)
Pin Connections (top view)
IN
VREF
CD
TD352
VH
OUT
VL
DESAT
CLAMP
Order Codes
Part Number
TD352IN
TD352ID
TD352IDT
Temperature Range
-40°C, +125°C
Package
DIP
SO
Packaging
Tube
Tape & Reel
Marking
TD352I
TD352I
TD352I
December 2004
Revision 1
1/13
1 page  
Functional Description
TD352
4 Functional Description
4.1 Input stage
TD352 IN input is clamped at about 5V to 7V. The input is triggered by the signal edge. When using an
open collector optocoupler, the resistive pull-up resistor can be connected to either VREF or VH.
Recommended pull-up resistor value with VH=16V are from 4.7k to 22k.
4.2 Voltage reference
A voltage reference is used to create accurate timing for the turn-on delay with external resistor and
capacitor. The same circuitry is also used for the two-level turn-off delay.
A decoupling capacitor (10nF to 100nF) on VREF pin is required to ensure good noise rejection.
4.3 Active Miller clamp:
The TD352 offers an alternative solution to the problem of the Miller current in IGBT switching
applications. Instead of driving the IGBT gate to a negative voltage to increase the safety margin, the
TD352 uses a dedicated CLAMP pin to control the Miller current. When the IGBT is off, a low impedance
path is established between IGBT gate and emitter to carry the Miller current, and the voltage spike on
the IGBT gate is greatly reduced.
During turn-off, the gate voltage is monitored and the clamp output is activated when gate voltage goes
below 2V (relative to VL). The clamp voltage is VL+4V max for a Miller current up to 500mA. The clamp
is disabled when the IN input is triggered again.
The CLAMP function doesn’t affect the turn-off characteristic, but only keeps the gate to the low level
throughout the off time. The main benefit is that negative voltage can be avoided in many cases, allowing
a bootstrap technique for the high side driver supply.
4.4 Turn-on delay
Turn-on (Ta) delay is programmable through external resistor Rd and capacitor Cd for accurate timing. Ta
is approximately given by:
Ta (µs) = 0.7 * Rd (kohms) * Cd (nF)
The turn-on delay can be disabled by connecting the CD pin to VREF with a 4.7k resistor.
Input signals with ON-time smaller than Ta are ignored.
4.5 Desaturation protection
Desaturation protection ensures the protection of the IGBT in the event of overcurrent. When the DESAT
voltage goes higher than VH-2V, the TD352 OUT pin is driven low. The fault state is only exit after power-
down and power-up.
A programmable blanking time is used to allow enough time for IGBT saturation. Blanking time is
provided by an internal current source and external Cdes capacitor, the Tbdes blanking time value is given
by:
Tbdes = Vdes * Cdes / Ides
At VH=16V, Tbdes is approximately given by:
Tbdes (µs) = 0.056 * Cdes (pF)
4.6 Output stage
The output stage is able to sink/source 1.7A/1.3A typical at 25°C and 1.0A/0.75A min. over the full
temperature range. This current capability is specified near the usual IGBT Miller plateau.
5/13
5 Page 
Package Mechanical Data
8 Package Mechanical Data
8.1 DIP-8 Package
Plastic DIP-8 MECHANICAL DATA
DIM.
A
a1
B
B1
b
b1
D
E
e
e3
e4
F
I
L
Z
MIN.
0.7
1.39
0.91
0.38
0.44
mm.
TYP
3.3
0.5
8.8
2.54
7.62
7.62
3.3
MAX.
1.65
1.04
0.5
9.8
7.1
4.8
1.6
MIN.
0.028
0.055
0.036
0.015
0.017
inch
TYP.
0.130
0.020
0.346
0.100
0.300
0.300
0.130
TD352
MAX.
0.065
0.041
0.020
0.386
0.280
0.189
0.063
P001F
11/13
11 Page | ||
| Páginas | Total 13 Páginas | |
| PDF Descargar | [ Datasheet TD352.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TD350 | Advanced IGBT/MOSFET Driver | ST Microelectronics |
| TD350E | Advanced IGBT/MOSFET driver |  STMicroelectronics |
| TD351 | Advanced IGBT/MOSFET Driver | ST Microelectronics |
| TD352 | Advanced IGBT/MOSFET Driver | ST Microelectronics |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |