|
|
PDF SDA2546-5 Data sheet ( Hoja de datos )
| Número de pieza | SDA2546-5 | |
| Descripción | Nonvolatile Memory 4-Kbit E2PROM | |
| Fabricantes | Siemens Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SDA2546-5 (archivo pdf) en la parte inferior de esta página. Total 12 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
Nonvolatile Memory 4-Kbit E2PROM
with I2C Bus Interface
Preliminary Data
Features
q Word-organized reprogrammable nonvolatile memory
in n-channel floating-gate technology (E2PROM)
q 512 × 8-bit organization
q Supply voltage 5 V
q Serial 2-line bus for data input and output (I2C Bus)
q Reprogramming mode, 10 ms erase/write cycle
q Reprogramming by means of on-chip control (without
external control)
q The end of the programming cycle can be checked
q Data retention in excess of 10 years
q More than 104 reprogramming cycles per address
Type
SDA 2546-5
Ordering Code
Q67100-H5096
SDA 2546-5
MOS IC
P-DIP-8-1
Package
P-DIP-8-1
Circuit Description
I2C Bus Interface
The I2C Bus is a bidirectional 2-line bus for the transfer of data between various integrated circuits.
It consists of a data line SDA and a clock line SCL. The data line requires an external pull-up resistor
to VCC (open drain output stages).
The possible operational states of the I2C Bus are shown in figure 1. In the quiescent state, both
lines SDA and SCL are high, i.e. the output states are disabled. As long as SCL remains "1",
information changes on the data bus indicate the start or the end of a data transfer between two
components. The transition on SDA from "1" to "0" is a start condition, the transition from "0" to "1"
a stop condition. During a data transfer the information on the data bus will only change when the
clock line SCL is "0". The information on SDA is valid as long as SCL is "1".
In conjunction with an I2C Bus system, the device can operate as a receiver, and as a transmitter
(slave receiver/listener, or slave transmitter/talker). Between the falling edge of the eighth
transmission pulse and a ninth acknowledge clock pulse, the device sets the SDA-line to low as a
reception confirmation, if the chip select conditions have been met. During the output of data, the
data output of the memory becomes high, during the ninth clock pulse (acknowledge master).
The signal timing required for the operation of the I2C Bus is summarized in figure 2.
Semiconductor Group
29
07.94
1 page  
SDA 2546-5
Block Diagram
Semiconductor Group
33
5 Page 
SDA 2546-5
Figure 3
Programming
Control word input
ST CS/E As
WA
As
DE
As
SP
(the reprogramming starts after
this stop condition)
Check for program end by ST CS/A As
1. when As = 1 programming is not finished
2. when As = 0 programming is finished
Program interruption by
ST CS/E As
Figure 4
Read
Control word input read
a) complete (with word address input)
ST CS/E As WA As ST CS/A As DA Am DA Am SP
n bytes
Last byte
Automatic incrementation
of the word address
b) shortened:
Bit 0 … 8 the last adapted word
address keep unchanged
ST CS/A As DA Am DA Am SP
n bytes
Last byte
Autoincrement
before stop condition
Am = 0
Am = 1
Semiconductor Group
39
11 Page | ||
| Páginas | Total 12 Páginas | |
| PDF Descargar | [ Datasheet SDA2546-5.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SDA2546-5 | Nonvolatile Memory 4-Kbit E2PROM | Siemens Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |