DataSheet.es    

PDF 715P Datasheet ( Hoja de datos )

Número de pieza 715P
Descripción Polypropylene Film Capacitors ORANGE DROP
Fabricantes Vishay Siliconix 
Logotipo Vishay Siliconix Logotipo

Total 7 Páginas
		
715P Hoja de datos, Descripción, Manual
www.DataSheet4U.com
Polypropylene Film Capacitors
ORANGE DROP®, Low Loss
Type 715P
Vishay Sprague
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 55°C to + 85°C standard; up to
+ 105°C when working voltage is reduced to 50% of the
+ 85°C rating.
Insulation Resistance: After a 2 minute charge at rated
voltage or 500 V, whichever is less.
At + 25°C: 400,000 Megohm for C .5µF.
200,000 Megohm - Microfarads for C > .5 Microfarads.
At + 85°C: 20,000 Megohm for C .5 Microfarads.
10,000 Megohm - Microfarads for C > .5 Microfarads.
At + 105°C: 2000 Megohm for C .5µF.
1000 Megohm - Microfarads for C > .5 Microfarads.
Capacitance, Tolerance and Dissipation Factor:
Capacitors shall be measured at a frequency of 1000Hz
at + 25°C or else be referred to measurements made at
that frequency and temperature. The maximum dissipation
factor shall be 0.1%.
Dielectric Withstanding Voltage: Capacitors rated below
1000 volts shall withstand a DC potential of 250% of rated
voltage applied between terminals for not more than
5 seconds. Capacitors rated 1000 volts and above shall
withstand a DC potential of 200% of rated voltage applied
between the terminals for not more than 5 seconds. The
test voltage must be applied and discharged through a
resistor of one ohm per volt.
Polypropylene plastic film is employed as the dielectric in Type
715P ORANGE DROP® capacitors. Type 715P capacitors
are ideal for applications where high AC current flow is found,
as in certain solid-state TV vertical circuits,
r-f generators and pulse-forming networks where dielectric
heating is often a problem.
The polypropylene dielectric film is similar to polystyrene in
that it can handle high AC currents due to its low loss but with
the added advantage of an operating temperature to
+ 105°C.
Capacitance change with temperature is less than 3% over
the entire operating temperature range. The temperature
coefficient is negative and virtually linear at 180PPM/°C over
the temperature range of + 25°C to + 105°C. This characteristic
means the Type 715P is suitable for matching with positive TC
resistors and inductors to maintain circuit stability.
Type 715P ORANGE DROP® capacitors are conformally
coated with a flame retardant epoxy.
Performance characteristics, as well as curves showing typical
variation in electrical characteristics as a function of temperature
and frequency, are given.
Humidity Test: Condition capacitors with no voltage
applied for 72 hours at 95% relative humidity and + 75°C.
Remove capacitors from humidity chamber, wipe surface
dry of moisture and dry in circulating air for 4 hours.
Measure insulation resistance after a two minute charge at
+ 25°C and rated voltage or 500 VDC, whichever is less.
Minimum product of insulation resistance and capacitance
shall be 50,000 Megohm-microfarads after test but need
not exceed 100,000 Megohm. Not more than one failure
in 12 units tested shall be permitted.
DC Life Test: Capacitors are capable of withstanding a
500 hour life test at + 85°C at 150% of rated working
voltage. After test, capacitance shall not have changed by
more than 5% of initial value, insulation resistance shall
not have decreased by more than 50% of the initial limit
and dissipation factor shall not have increased to more
than 0.1%.
AC Life Test: Capacitors shall withstand the maximum
60Hz voltage for a period of 500 hours at + 85°C.
Rated DC Voltage
200
400, 600
800, 1200, 1600
Maximum 60Hz Voltage
155
200
500
Not more than one failure allowed in 12 units tested.
Document Number: 42018
Revision 13-Nov-03
For technical questions, contact spresale@vishay.com
www.vishay.com
47

1 page

715P pdf
Type 715P
Vishay Sprague
STANDARD RATINGS* in inches [millimeters]
µF
± 10% TOLERANCE
PART NUMBER
800 VDC/450 VAC**
L
SIZE
D
.0056
715P56298L
1.30 [33.02]
0.50 [12.70]
.0068
715P68298L
1.30 [33.02]
0.50 [12.70]
.0082
715P82298L
1.30 [33.02]
0.50 [12.70]
.01
715P10398L
1.30 [33.02]
0.50 [12.70]
.012
715P12398L
1.30 [33.02]
0.55 [13.97]
.015
715P15398L
1.30 [33.02]
0.55 [13.97]
.018
715P18398L
1.30 [33.02]
0.60 [15.24]
.022
715P22398L
1.30 [33.02]
0.60 [15.24]
.027
715P27398L
1.30 [33.02]
0.70 [17.78]
.033
715P33398L
1.30 [33.02]
0.70 [17.78]
.039
715P39398M
1.70 [43.18]
0.70 [17.78]
.047
715P47398M
1.70 [43.18]
0.70 [17.78]
.056
715P56398M
1.70 [43.18]
0.80 [20.32]
.068
715P68398M
1.70 [43.18]
0.80 [20.32]
.082
715P82398M
1.70 [43.18]
0.90 [22.86]
.1
715P10498M
1.70 [43.18]
0.90 [22.86]
.0027
1200 VDC/475 VAC**
715P272912L
1.30 [33.02]
0.50 [12.70]
.0033
715P332912L
1.30 [33.02]
0.50 [12.70]
.0039
715P392912L
1.30 [33.02]
0.50 [12.70]
.0047
715P472912L
1.30 [33.02]
0.50 [12.70]
.0056
715P562912L
1.30 [33.02]
0.55 [13.97]
.0068
715P682912L
1.30 [33.02]
0.55 [13.97]
.0082
715P822912L
1.30 [33.02]
0.60 [15.24]
.01
715P103912L
1.30 [33.02]
0.60 [15.24]
.012
715P123912L
1.30 [33.02]
0.65 [16.51]
.015
715P153912L
1.30 [33.02]
0.65 [16.51]
.018
715P183912M
1.70 [43.18]
0.65 [16.51]
.022
715P223912M
1.70 [43.18]
0.65 [16.51]
.027
715P273912M
1.70 [43.18]
0.75 [19.05]
.033
715P333912M
1.70 [43.18]
0.75 [19.05]
.039
715P393912M
1.70 [43.18]
0.85 [21.59]
.047
715P473912M
1.70 [43.18]
0.85 [21.59]
1600 VDC/500 VAC**
.0018
715P182916L
1.30 [33.02]
0.50 [12.70]
.0022
715P222916L
1.30 [33.02]
0.50 [12.70]
.0027
715P272916L
1.30 [33.02]
0.55 [13.97]
.0033
715P332916L
1.30 [33.02]
0.55 [13.97]
.0039
715P392916L
1.30 [33.02]
0.60 [15.24]
.0047
715P472916L
1.30 [33.02]
0.60 [15.24]
.0056
715P562916L
1.30 [33.02]
0.65 [16.51]
.0068
715P682916L
1.30 [33.02]
0.65 [16.51]
.0082
715P822916L
1.30 [33.02]
0.70 [17.78]
.01
715P103916L
1.30 [33.02]
0.70 [17.78]
.012
715P123916M
1.70 [43.18]
0.75 [19.05]
.015
715P153916M
1.70 [43.18]
0.75 [19.05]
.018
715P183916M
1.70 [43.18]
0.85 [21.59]
.022
715P223916M
1.70 [43.18]
0.85 [21.59]
.027
715P273916M
1.70 [43.18]
0.95 [24.13]
.033
715P333916M
1.70 [43.18]
0.95 [24.13]
* Shaded items, when ordered as ± 5% tolerance with D3 leads, are standard capacitors in stock and available through the Sprague® Distribution
Network. To complete the Type 715P Part Number, add the "D3" suffix and change the capacitance tolerance code number from a "9" to a "5"
to indicate ± 5% (i.e., 715P10456LD3). Any other Part Number, value or type may easily be ordered as a Special.
** 60Hz rms.
Document Number: 42018
Revision 13-Nov-03
For technical questions, contact spresale@vishay.com
www.vishay.com
51

5 Page



PáginasTotal 7 Páginas
PDF Descargar[ 715P.PDF ]

Enlace url


Hoja de datos destacado

Número de piezaDescripciónFabricantes
7150-130mA Low Power LDOHoltek
Holtek
7151Submicro Axial Lead Lamp/Micro Axial Lead Lamps/Axial Lead LampsGilway Technical Lamp
Gilway Technical Lamp
7153T- Subminiature LampsGilway Technical Lamp
Gilway Technical Lamp
7154Submicro Axial Lead Lamp/Micro Axial Lead Lamps/Axial Lead LampsGilway Technical Lamp
Gilway Technical Lamp

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


www.DataSheet.es    |   2018   |  Privacy Policy  |  Contacto  |  Buscar