DataSheet.es    


PDF B1117 Data sheet ( Hoja de datos )

Número de pieza B1117
Descripción Low Dropout Voltage Regulator
Fabricantes Bay Linear 
Logotipo Bay Linear Logotipo



Hay una vista previa y un enlace de descarga de B1117 (archivo pdf) en la parte inferior de esta página.


Total 7 Páginas

No Preview Available ! B1117 Hoja de datos, Descripción, Manual

www.DataSheet4U.com
Bay Linear
Inspire the Linear Power
1.0Amp Low Dropout Voltage Regulator
Adjustable & Fix (0.40Volt Dropout)
B1117
Description
The Bay Linear B1117 is a three terminal positive NPN
regulator offered as adjustable or fix voltages of 1.5V,1.8V,
2.5V, 2.85V, 3.3V, and 5Volts. The output current has a
capability up to 1.0Amp,. This device has been optimized for
low voltage where transient response and minimum input
voltage are critical. The 2.85V version is designed specifically
to be used in active terminators for SCSI bus.
Current limit is trimmed to ensure specified output current and
controlled short-circuit current. On-Chip thermal limiting
provides protection against any combination of overload and
ambient temperatures that would create excessive junction
temperatures.
The B1117 is offered in a 3-pin SOT-223, and TO-252
(DPAK) packages compatible with other 3 terminal regulators.
5-pin version in TO-263 with lower dropout of 0.4 volt is
available.
Features
Adjustable Output Down to 1.2V
Output Current of 1.0Amp
Low Dropout 1.0V for B1117
Dropout of 0.40 V in for B1117A
Adjustable & Fix 1.5V, 1.8V, 2.5V, 2.85V,
3.0V, 3.3V, 5.0V
0.05% Load Regulation
Current & Thermal Limiting
Lower Cost SOT-89 Package
Available in SOT-223, and TO-252,
TO-263 & SO-8
Similar to industry Standard LT1117
Applications
Active SCSI terminators
High efficiency Linear Regulator
Post regulators fro Switching Supplies
Battery Charger
5V to 3.3V linear Regulators
Motherboard Clock Supplies
Pin Connection
8-Pin Surface Mount
ADJ 1
8 IN
NC 2
7 IN
OUT
3
6 IN
OUT
4
5 N.C.
Top View
SOT-223
Tab VOUT
Adj/GND OUT IN
Front View
Ordering Information
Devices
B1117D-X
B1117N-X
B1117T-X
B1117S-X
B1117M-X
Package
TO-252
TO-223
TO-220
TO-263
SO-8
Temp.
0 °C to 125 °C
0 °C to 125 °C
0 °C to 125 °C
0 °C to 125 °C
0 °C to 125 °C
SOT -223-5
Tab V OUT
1234 5
Front View
#1 Sense
#2 Adj/GND
#3 OUT
#4 Control
#5 VIN
TO-252
1 23
ADJ/GN VOUT VIN
Front
5 VPOWER
4 VCONTROL
3 OUTPUT
2 ADJ/GND.
1 SENSE
TO-263-5 Package
Bay Linear, Inc 2418 Armstrong Street, Livermore, CA 94550 Tel: (925) 606-5950, Fax: (925) 940-9556
www.baylinear.com

1 page




B1117 pdf
APPLICATION NOTES EXTERNAL
CAPACITOR
To ensure the stability of the B1117 an output capacitor of at
least 10µF (tantalum)or 50µF (aluminum) is required. The
value may change based on the application requirements on
the output load or temperature range. The capacitor
equivalent series resistance (ESR) will effect the B1117
stability. The value of ESR can vary from the type of
capacitor used in the applications. The recommended value
for ESR is 0.5. The output capacitance could increase in
size to above the minimum value. The larger value of
output capacitance as high as 100µF can improve the load
transient response.
SOLDERING METHODS
The B1117 SOT-223 package is designed to be compatible
with infrared reflow or vapor-phase reflow soldering
techniques. During soldering the non-active or mildly active
fluxes may be used. The B1117 die is attached to the heat
sink lead which exits opposite the input, output, and ground
pins.
Hand soldering and wave soldering should be avoided since
these methods can cause damage to the device with
excessive thermal gradients on the package. The SOT-223
recommended soldering method are as follows: vapor phase
reflow and infrared reflow with the component preheated to
within 65°C of the soldering temperature range.
THERMAL CHARACTERISTICS
The thermal resistance of B1117 is 15°C/W from junction to
tab and 31 °C/W from tab to ambient for a total of 46 °C/W
from junction to ambient. The B1117 features the internal
thermal limiting to protect the device during overload
conditions. Special care needs to be taken during continues
load conditions the maximum junction temperature does not
exceed 125 °C.
Taking the FR-4 printed circuit board and 1/16 thick with 1
ounce copper foil as an experiment (fig.1 & fig.2), the PCB
material is effective at transmitting heat with the tab
attached to the pad area and a ground plane layer on the
backside of the substrate. Refer to table 1 for the results of
the experiment.
The thermal interaction from other components in the
application can effect the thermal resistance of the B1117.
The actual thermal resistance can be determined with
experimentation. B1117 power dissipation is calculated as
follows:
PD = (VIN - VOUT)(IOUT)
B1117
Maximum Junction Temperature range:
TJ = Tambient (max) + PD* thermal resistance (Junction-to-
ambient)
Maximum Junction temperature must not exceed the
125°C.
10V
B1117-2.85
+
10uF
+
10uF
2.85V
27K..
PO = (10V - 2.85)(105mA) = (7.15)(105mA) = 750mW
Fig. 1. Circuit Layout, Thermal Experiments.
50 X 50 mm
35 X 17 mm
16 X 10 mm
Fig. 2. Substrate Layout for SOT-223
Bay Linear, Inc 2418 Armstrong Street, Livermore, CA 94550 Tel: (925) 606-5950, Fax: (925) 940-9556
www.baylinear.com

5 Page










PáginasTotal 7 Páginas
PDF Descargar[ Datasheet B1117.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
B1110SURFACE MOUNT SCHOTTKY BARRIER RECTIFIERSLite-On Technology
Lite-On Technology
B1114PNP Transistor - 2SB1114NEC
NEC
B1115PNP Transistor - 2SB1115NEC
NEC
B1115PNP SILICON EPITAXIAL TRANSISTORRenesas
Renesas

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar