|
|
Número de pieza | CDB4391A | |
Descripción | Evaluation Board | |
Fabricantes | Cirrus Logic | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de CDB4391A (archivo pdf) en la parte inferior de esta página. Total 24 Páginas | ||
No Preview Available ! www.DataSheet4U.com
CDB4391A
Evaluation Board for CS4391A
Features
z Demonstrates recommended layout and
grounding arrangements
z CS8414 receives AES/EBU, S/PDIF, &
EIAJ-340 compatible digital audio
z Digital and analog patch areas
z Requires only a digital signal source and
power supplies for a complete Digital-to-
Analog (D/A) converter system
Description
The CDB4391A evaluation board is an excellent means
for quickly evaluating the CS4391A 24-bit, stereo D/A
converter. Evaluation requires an analog signal
analyzer, a digital signal source, a PC for controlling the
CS4391A (for control port mode only) and a power
supply. Analog line level outputs are provided via RCA
phono jacks.
The CS8414 digital audio receiver IC provides the sys-
tem timing necessary to operate the D/A converter and
will accept AES/EBU, S/PDIF, and EIAJ-340 compatible
audio data. The evaluation board may also be config-
ured to accept external timing and data signals for
operation in a user application during system
development.
ORDERING INFORMATION
CDB4391A
Evaluation Board
I/O for
Clocks
and Data
Control
Port
CS8414
Digital
Audio
Interface
CS4391A
Channel A
Output and Mute
Channel B
Output and Mute
www.cirrus.com
Copyright Cirrus Logic, Inc. 2003
(All Rights Reserved)
MAY ‘03
DS600DB1
1
1 page CDB4391A
4. CS8414 DATA FORMAT
The CS8414 data format can be set with switches M0, M1, M2, and M3, as described in the CS8414 data
sheet. The format selected must be compatible with the data format of the CS4391A, as shown in the
CS4391A data sheet. Please note that the CS8414 does not support all the possible modes of the CS4391A
and the Left-Justified Format for the CS8414 and the CS4391A have incompatible serial clocks, see
Table 1. The default settings for M0-M3 on the evaluation board are given in Tables 3-4.
CS4391A CP
Mode Format
0
1
2
3
4
5
CS4391A SA
Mode Format
0
1
2
3
-
-
CS8414
Format
Unsupported
2
5
Unsupported
Unsupported
6
Table 1. CS8414 Supported Formats
5. INPUT/OUTPUT FOR CLOCKS AND DATA
The evaluation board has been designed to allow interfacing to external systems via the 10-pin header, J9.
This header allows the evaluation board to accept externally generated clocks and data. The schematic for
the clock/data I/O is shown in Figure 9. The 74HC243 transceiver functions as an I/O buffer where HRD1
through HRD6 determine if the transceiver operates as a transmitter or receiver. A transmit function is im-
plemented with all jumpers, HRD1 through HDR6 in the 8414 position. LRCK, SDATA, and SCLK from
the CS8414 will be outputs on J9. The transceiver operates as a receiver with HRD1 through HDR6 in the
EXT_CLK position. MCLK, LRCK, SDATA and SCLK on J9 become inputs.
6. POWER SUPPLY CIRCUITRY
Power is supplied to the evaluation board by six binding posts (GND, +5V(J6), +5V(J1), VL, VCC and
VEE), see Figure 10. The +5V(J6) input supplies power to the +5 volt digital circuitry (V+5, VD+5, VD-
PC+5), while the VL input supplies power to the Voltage Level Converters and the CS4391A VL pin.
+5V(J1) supplies power to the CS4391A. VCC and VEE supply power to the op-amp and can be +/-9 to
+/-12 volts.
WARNING: Refer to the CS4391A data sheet for maximum allowable voltages levels. Operation outside
of this range can cause permanent damage to the device.
7. GROUNDING AND POWER SUPPLY DECOUPLING
The CS4391A requires careful attention to power supply and grounding arrangements to optimize perfor-
mance. Figure 10 details the power distribution used on this board. The decoupling capacitors are located
as close to the CS4391A as possible. Extensive use of ground plane fill in the evaluation board yields large
reductions in radiated noise.
DS600DB1
5
5 Page CDB4391A
DS600DB1
11
11 Page |
Páginas | Total 24 Páginas | |
PDF Descargar | [ Datasheet CDB4391A.PDF ] |
Número de pieza | Descripción | Fabricantes |
CDB4391 | 24-Bit/ 192 kHz Stereo DAC with Volume Control | Cirrus Logic |
CDB4391A | Evaluation Board | Cirrus Logic |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |