DataSheet.es    


PDF AG2120 Data sheet ( Hoja de datos )

Número de pieza AG2120
Descripción FULLY FEATURED PSTN INTERFACE
Fabricantes Silver 
Logotipo Silver Logotipo



Hay una vista previa y un enlace de descarga de AG2120 (archivo pdf) en la parte inferior de esta página.


Total 14 Páginas

No Preview Available ! AG2120 Hoja de datos, Descripción, Manual

www.DataSheet4U.com
Silver
TELECOM
TIP
RING
TRUNK
VIN
VOUT
Control and
Supervision
V2.0October 2002
Ag2120Advance data Sheet
FULLY FEATURED
PSTN INTERFACE
FEATURES
• A highly featured PSTN Interface (COIC,
FXO, DAA, Trunk Interface) in a single DIL
or 12mm high SIL device.
• +5V or +3.3V supply.
• Transformer isolation providing high
common mode rejection (CMRR) for use in
un-grounded systems.
• Highly integrated with on board loop switch
and integral diode bridge.
• Loop start circuit, ringing detect and loop
current detection. Parallel phone detect.
• Tip-ring polarity reversal detect (for Caller
Line ID and remote metering) and on-hook
reception.
• Meets requirements of EN60950/UL1950,
and FCC Pt68. Low cost power cross
protection.
• Programmable d.c. mask, line and network
impedances.
• Silver Telecom “design-in” assistance.
DESCRIPTION
The Ag2120 is a self-contained highly
integrated PSTN Interface Circuit in a single
SIL or DIL Module.
In addition to the features listed, the Ag2120
allows flexible programming of many
functions, including the dc voltage mask and
impedances. The Ag2120 meets international
safety and regulatory requirements.
The device requires a minimum of external
components and has been specified for ease
of use, to reduce time to market.
The Ag2120 is designed for all applications,
including those where there is a high level of
common mode interference, such as PABX,
long loop applications and systems without a
ground.
© Silver Telecom 2002

1 page




AG2120 pdf
V2.0 October 2002
Advance Data Sheet
Ag2120
FULLY FEATURED PSTN INTERFACE
2.0 Line Interfacing
The Ag2120 line interface provides a flexible and
robust interface to the telephone line. It has been
designed to meet regulatory standards whilst providing
a space and power efficient solution.
2.1 D.C. Termination.
ringing signal. The LSC pin can be controlled by the
output drive pins of a Codec or from a micro controller
device.
Once the Loop Switch has been closed confirmation
that loop current is flowing is provided by the LC pin.
This can be used for fault detection and for call clear
detection.
Any equipment terminating a telephone line must
present the correct d.c. resistance to the line. This
ensures that the correct current flows to be able to
detect the off hook condition, avoids excessive power
dissipation in the Subscriber Line Interface (SLIC) and
the Subscriber’s equipment, and minimises the size of
power supply needed to drive the SLIC.
The Ag2120 has been designed to meet the
requirements of many network operators. This is done
by making the d.c. characteristic adjustable. These are
controlled by connecting the DM pins on the line side of
the circuit. Table 1 shows how these are connected.
2.2.2 Ringing Detection and Sensitivity.
The terminal equipment must be capable of detecting
and responding to an incoming call in the same way as
a telephone set. The termination circuitry must,
therefore, detect the presence of the ringing signal.
The Ag2120 provides an output, RS, which indicates
the presence of ringing by switching from a logic 1 to
logic 0. The RS output will toggle at the ringing
frequency. A capacitor to ground can also be added if
ringing cadence is needed rather than the ringing
frequency.
Table 1 Set Up of the DM Pins
Market
DMa
DMb
North America
(EIA 464, Resistive)
Europe (CTR21)
Far East
Connect together through
390K resistor
Connect together through
390K resistor
Connect together through
390K resistor
2.2 Signalling and Loop Status.
The Ag2120 provides facilities to monitor and control
the telephone line. This allows the device to be used
with a variety of loop signalling schemes and minimises
the number of external components needed to
implement a complete line interface.
In order to implement ground start applications please
contact Silver Telecom or our local representative.
2.2.1 The On-Board Loop Switch
The Ag2120 implements the loop start protocol when
initiating and answering a call. This means that a
switch must be closed to allow loop current to flow,
signalling to the SLIC that the terminating equipment
has gone “off-hook”. This has been done historically
by a relay. The Ag2120 uses an integral optically
isolated switch to do this, eliminating the need for an
external relay, so space and cost is saved for the user.
The on-board Loop Switch is controlled by the LSC pin.
A logic 1 applied to the pin closes the loop switch. This
is done when the terminating equipment wishes to
begin a call or in response to the reception of the
The sensitivity to ringing is set internally to 22VRMS
when VCC is +5V, or 14VRMS when VCC is +3.3V.
2.2.3 Reversal Detect
The reversal of the battery polarity is used as a
signalling technique. The Ag2120 can detect this
condition and provides an output on the F/R pin,
whether in the on-hook or off-hook state.
One example of this type of signalling is in Caller Line
ID in the United Kingdom, where a battery polarity
reversal precedes the transmission of data before the
ringing signal is applied to the line. Another example is
in some systems in the US where a reversal is used to
indicate far end answer.
3.0 The 2-4 Wire (Hybrid) Conversion.
The Ag2120 transmits and receives balanced 2-wire
analog signals at the Tip and Ring connections. These
are converted to a ground referenced output at VOUT
and from a ground referenced signal at VIN.
VOUT and VIN are normally connected to a Codec (via
d.c. blocking capacitors) for conversion to and from a
Pulse Code Modulated (PCM) stream.
3.1 Transmit and Receive Gain.
The gain in both the transmit and receive directions is
set at 0dB. Any gain adjustments can be made using
the Codec functionality. This is either by hardware or
software depending upon the Codec used.
© Silver Telecom 2002
Page 5

5 Page





AG2120 arduino
V2.0 October 2002
Advance Data Sheet
10.0 AC Electrical Characteristics.
Ag2120
FULLY FEATURED PSTN INTERFACE
Characteristic
Sym Min Typ* Max Units Test Comments1
1
Ringing voltage: detect
Ringing voltage: no detect
2
Ringing voltage: detect
Ringing voltage: no detect
VRD
26
22
22
18
VRMS +5V operation
V
RD
18
14
14
10
V +3.3V operation
RMS
3 Ringing frequency
4 Input Impedance at VIN
5 Output impedance at Vout
6
Absolute voltage gain, 2 Wire to
VOUT
7
Absolute voltage gain, VIN to
2 Wire
FR 15
68 Hz
100 k
10
-0.5 +0.5 dB Off-hook
-0.5 +0.5 dB Off-Hook
8 On-hook gain, 2 Wire to VOUT
-0.5 +0.5 dB
9
Relative gain, referenced to
1kHz. 2Wire - Vout, Vin - 2Wire
-0.5 +0.5 dB 200 - 3400 Hz
10
Total harmonic distortion @
2Wire and Vout
THD
0.1 1.0 % @0dBm, 1kHz
11
Overload distortion @2 Wire and
V2
out
OD
0.5 5.0
%
@+3dBm,
1kHz
12 Common mode rejection ratio
CMRR 70 75
dB
50 – 500Hz
VCM = 60VRMS
13 Common mode overload level CMOL
250 300 VRMS 50 – 60Hz
14 Idle channel noise3
N
C
12.0
dBrnC @2 Wire & VOUT
15
Power supply rejection ratio
at 2 Wire and Vout
PSRR 25
dB
Ripple 0.1V,
1kHz on VCC
16 Return loss4
RL 18
dB 300-3400Hz
17 Transhybrid loss4
THL
18
21
dB 300-3400Hz
dB 500-2500Hz
18 Metallic to longitudinal balance
60 70
40 70
dB
200-1000Hz
1000-4000Hz
19
Leakage current, Tip or Ring to
analog ground
ILA
5 mARMS 1000V ac
All AC Electrical Characteristics are over the Recommended Operating Conditions with V at +5.0V +5%, unless otherwise stated.
CC
*Typical figures are at 25°C with nominal 5V supply and 25mA loop current unless otherwise stated. These figures are for design aid only.
1 For test circuit details please contact Silver Telecom.
2 These figures fpr+5V operation. For +3.3V operation, OD is typically 5% at +3dBm.
3 In the off-hook condition
4 Into a 600impedance
© Silver Telecom 2002
Page 11

11 Page







PáginasTotal 14 Páginas
PDF Descargar[ Datasheet AG2120.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
AG2120FULLY FEATURED PSTN INTERFACESilver
Silver

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar