DataSheet.es    


PDF ADM1170 Data sheet ( Hoja de datos )

Número de pieza ADM1170
Descripción Hot Swap Controller
Fabricantes Analog Devices 
Logotipo Analog Devices Logotipo



Hay una vista previa y un enlace de descarga de ADM1170 (archivo pdf) en la parte inferior de esta página.


Total 17 Páginas

No Preview Available ! ADM1170 Hoja de datos, Descripción, Manual

Data Sheet
1.6 V to 16.5 V Hot Swap Controller
with Soft Start
ADM1170
FEATURES
Controls supply rails from 1.6 V to 16.5 V
Supply voltage range from 2.7 V to 16.5 V
Allows protected board removal and insertion to a live
backplane
External sense resistor provides adjustable analog current
limit with circuit breaker
Soft start controls inrush current profile
Peak fault current limited with fast response
Charge pumped gate drive for external N-FET switch
Automatic retry or latch-off during current fault
Undervoltage lockout
8-lead, TSOT package
APPLICATIONS
Hot swap board insertion: line cards, raid systems
Industrial high-side switches/circuit breakers
Electronic circuit breakers
GENERAL DESCRIPTION
The ADM1170 is a hot swap controller that safely enables a
printed circuit board to be removed and inserted to a live
backplane. This is achieved using an external N-channel power
MOSFET with a current control loop that monitors the load
current through a sense resistor. An internal charge pump is
used to enhance the gate of the N-channel FET. When an
overcurrent condition is detected, the gate voltage of the FET is
reduced to limit the current flowing through the sense resistor.
The ADM1170 operates with a supply voltage ranging from
2.7 V to 16.5 V. By using independent SENSE pins from VCC,
the ADM1170 allows for the hot swap of supplies ranging down
to 1.6 V. During an overcurrent condition, the TIMER pin
capacitor determines the amount of time the FET remains at
a current limiting mode of operation until it is shut down. The
ON (ON-CLR) pin is the enable input for the device and can be
used to monitor the input supply voltage. The ADM1170 also
features soft start to provide the user with a capacitor program-
mable ramping reference to the internal current sense comparator.
This provides a linearly increasing current limit at startup at a
rate set by CSS. This helps to reduce and limit large inrush
currents.
This device is available in two options: the ADM1170-1 with
automatic retry for overcurrent fault and the ADM1170-2 with
latch-off for an overcurrent fault. Toggling the ON (ON-CLR)
pin resets a latched fault. The ADM1170 is packaged in an
8-lead TSOT.
VIN = 1.8V
VIN = 3.3VAUX
GND
FUNCTIONAL BLOCK DIAGRAM
LONG
RSENSE
LONG
SHORT RON1
RON2
LONG
SENSE+ SENSE–
VCC
GATE
ADM1170-1
ON
SS
CSS
TIMER
GND
CTIMER
Figure 1.
Q1 VOUT = 1.8V
CLOAD
GND
Rev. A
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibilityisassumedbyAnalogDevices for itsuse,nor foranyinfringementsofpatentsor other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarksandregisteredtrademarksarethepropertyoftheirrespectiveowners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2006–2013 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com

1 page




ADM1170 pdf
ADM1170
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
Rating
VCC Pin
SENSE+ Pin/SENSE− Pin
−0.3 V to +20 V
−0.3 V to +20 V
SENSE+ Pin − SENSE− Pin
±5 V
TIMER Pin
ON (ON-CLR) Pin
−0.3 V to (VCC + 0.3 V)
−0.3 V to +20 V
SS Pin
GATE Pin
Storage Temperature Range
Operating Temperature Range
Lead Temperature (10 sec)
Junction Temperature
–0.3 V to (VCC + 0.3 V)
−0.3 V to (VCC + 11 V)
−65°C to +125°C
−40°C to +85°C
300°C
150°C
Data Sheet
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL CHARACTERISTICS
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 3. Thermal Resistance
Package Type
8-Lead TSOT
θJA
152.9
Unit
°C/W
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. A | Page 4 of 16

5 Page





ADM1170 arduino
ADM1170
12
10
8
6
4
2
0
0 2 4 6 8 10 12 14 16
SUPPLY VOLTAGE (V)
Figure 28. GATE Current (Down) vs. Supply Voltage
18
–8
–9
–10
–11
–12
–13
–14
0 2 4 6 8 10 12 14 16
SUPPLY VOLTAGE (V)
Figure 29. GATE Current (up) vs. Supply Voltage
18
–11.0
–11.2
–11.4
–11.6
–11.8
–12.0
–12.2
–12.4
–12.6
VCC = 5V
VCC = 15V
VCC = 3V
VCC = 12V
–12.8
–13.0
–50
–25 0
25 50 75 100 125
TEMPERATURE (°C)
Figure 30. GATE Current (up) vs. Temperature
150
Data Sheet
–10.4
–10.5
–10.6
VCC = 3V
–10.7
–10.8
–10.9
VCC = 12V
VCC = 5V
VCC = 15V
–11.0
–50
–25 0
25 50 75 100 125
TEMPERATURE (°C)
Figure 31. Soft Start Current vs. Temperature
150
50
45
40
35
30
25
20
15
10
5
0
0 0.2 0.4 0.6 0.8 1.0 1.2
SOFT START VOLTAGE (V)
Figure 32. Circuit Breaker Voltage vs. Soft Start Voltage
Rev. A | Page 10 of 16

11 Page







PáginasTotal 17 Páginas
PDF Descargar[ Datasheet ADM1170.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
ADM1170Hot Swap ControllerAnalog Devices
Analog Devices
ADM1171Hot Swap ControllerAnalog Devices
Analog Devices
ADM1172Hot Swap ControllerAnalog Devices
Analog Devices
ADM11732.7V to 16.5V Hot Swap ControllerAnalog Devices
Analog Devices

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar