![]() |
|
Número de pieza | XE900SL10 | |
Descripción | Miniature Spread Spectrum Transceiver | |
Fabricantes | Xecom | |
Logotipo | ![]() |
|
Hay una vista previa y un enlace de descarga de XE900SL10 (archivo pdf) en la parte inferior de esta página. Total 16 Páginas | ||
No Preview Available !
www.DataSheet4U.com
XE900SL10
June 2005
XE900SL10 Miniature Spread Spectrum Transceiver
Description
The XE900SL10 breaks new ground in Smart Transceiver
Technology. It is a 900 MHz, Spread Spectrum
Transceiver with integral micro-controller, just 1 inch
square. This miniature size combined with low power
consumption make the XE900SL10 perfect for mobile
and battery powered applications.
Xecom did not drop features to reduce size. The
XE900SL10 still supports Xecom’s Count-Off™ feature
enabling a scan of up to 125 remote nodes in under 10
seconds. SensorOnAir™ allows sensors and control
lines to utilize the embedded communications controller
in place of a host micro-controller .
Xecom also offers a high power spread spectrum model,
the XE900S-500, for applications that require greater
range. The XE900S-500 has an obstructed range of up
to 1000 feet in a larger but still small package.
The XE900SL10 transmits at up to 10 milliwatts with a
receive sensitivity of -100 dBm to provide an obstructed
range of 300 feet. All from a 1 inch square transceiver
consuming less than .2W of power.
Features
* Small Size: 1.0” by 1.0” by 0.26”
* Serial Control and Configuration of the Wireless Link.
* Supports a 254 node point-to-multipoint network
* Output Power Programmable from 0 to 10 mW;
* Maximum Receiver Sensitivity -100 dBm
* Obstructed signal range to 300 feet;
* Wireless Data Rate 76.8K bps, half-duplex;
* Power Consumption:
55 mA @ 3.3 Volts when transmitting at 10 mW
less than 1 mA in Sleep Mode or Power-Down modes
* SensorOnAir™ allows direct connection of sensors to
the Smart Transceiver
* Count-Off™ allows the master node to download the
status of all nodes in under 10 seconds.
* Operating Temperature Range of -40 to +85 C
* FCC Part 15 Registered
Antenna
XE900SL10 Block Diagram
ROM
SAW
FILTER
MUX
UHF
TRANSCEIVER
Serial
I/F
Analog
Inputs
Digital
I/O
XECOM
(1) XE900SL10
1 page ![]() ![]() XE900SL10 PIN CONFIGURATION
/TXD 1
/RXD 2 XE900SL10
/CTS 3 Top View
Antenna
/RTS 4
DIO3 5
14 Reset
DIO2 6
13 ADC0
DIO1 7
12 ADC1
DIO0 8
11 VCC
N/C 9
10 GND
SIGNAL
/TXD
/RXD
/CTS
/RTS
DIO3
DIO2
DIO1
DIO0
N/C
GND
VCC
ADC1
ADC0
Reset
PINS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
DESCRIPTION
Transmit Data is the data input to the XE900SL10.
Received Data is the data output from the XE900SL10.
Clear to Send provides hardware flow control from the XE900SL10. The XE900SL10
drives /CTS high to signal the host to temporarily stop the flow of data into /TXD.
Request to Send provides hardware flow control from the host system. The host system
drives /RTS high to signal the XE900SL10 to temporarily stop the data flow onto /RXD.
DIO3 may be programmed as either a digital input or digital output. It connects directly to
the communications controller in the XE900SL10.
DIO2 may be programmed as either a digital input or digital output. It connects directly to
the communications controller in the XE900SL10.
DIO1 may be programmed as either a digital input or digital output. It connects directly to
the communications controller in the XE900SL10.
DIO0 may be programmed as either a digital input or digital output. It connects directly to
the communications controller in the XE900SL10.
No Connection
Common voltage reference for the XE900SL10.
3.3 Volt power for the XE900SL10.
Analog Input 1 to the XE900SL10’s communications controller. ADC1 connects to an
internal 12-bit Analog to Digital Convertor. ADC1 may also be configured as a digital
input if no analog inputs are required.
Analog Input 0 to the XE900SL10’s communications controller. ADC0 connects to an
internal 12-bit Analog to Digital Convertor. ADC0 may also be configured as a digital
input if no analog inputs are required.
Provides an active high hardware reset to the XE900SL10.
XECOM
(5) XE900SL10
5 Page ![]() ![]() AT COMMANDS
An asterisk indicates the factory default
A Answer Command - forces the smart transceiver
respond to a summons from another wireless device.
Dn Initiate a Wireless Link - attempts to establish a
connection with the transceiver at address n.
En Echo Characters - determines if the XE900SL10 will
echo the characters received on its serial interface during
command mode.
n=0 Characters not Echoed
n=1 Characters Echoed *
In Identification - displays product identification code.
n=0 Display Product Code
n=1 Display Product Name
n=2 Display Model Number
n=3 Display Copyright
n=4 Display Firmware Revision
Qn Result Code Display - determines if result codes will
be displayed.
n=0 Display Result Codes *
n=1 Do not Display Result Codes
Sn= Set Value of Register Sn
Sn? Read Value of Register Sn
Vn Response Type - selects Full Word or Numeric
responses
n=0 Numeric Responses
n=1 Full Word Responses *
Zn Reset - executes a soft Reset
n=0 Reset to Values Stored in User Profile 0 *.
n=1 Reset to Values Stored in User Profile 1
&F Restore Factory Settings - returns all configuration
commands and registers to their factory default values.
&IAn? Read Local Analog Input “n” - This command allows
the host equipment to read the values of the local analog
inputs.
n=0 Read input ADC0
n=1 Read input ADC1
&IDn? Read Local Digital Input “n” - This command
allows the host equipment to read the status of the local
digital inputs.
n=0 Read input DIO0
n=1 Read input DIO1
n=2 Read input DIO2
n=3 Read input DIO3
n=4 Read input DIO4 (pin shared with ADC0)
n=5 Read input DIO5 (pin shared with ADC1)
&IDn=z Set Local Digital Output “n” - This command
allows the host equipment to set the condition of the
local digital outputs. When z=0 the output is set to a
logic low; when z=1 the output is set to a logic high.
n=0 Set output DIO0
n=1 Set output DIO1
n=2 Set output DIO2
n=3 Set output DIO3
&Kn Flow Control - selects the type of flow control to be
used between the system host and the XE900SL10
n=0 Flow Control Disabled
n=3 RTS/CTS, hardware Flow Control
n=4 XON/XOFF, in-band Flow Control
&V View Active Configuration - sends the active
configuration data to the system host.
&Wn Store Current Configuration - loads the current
XE900SL10 configuration into either User Profile 0 or
User Profile 1.
n=0 load configuration into User Profile 0
n=1 load configuration into User Profile 1
#B Wireless Broadcast Mode - initiates wireless
broadcast mode for diagnostic purposes.
#C Count-Off Request (ASCII) - Initiates a “count-off’
sequence in the network with node status to be reported
in ASCII format.
#E: Count-Off Response (ASCII) - Programs the nodes 8
byte response to a “count-off’ request from the
network hub in ASCII format.
#E= Count-Off Response (Hex) - Programs the nodes 8
byte response to a “count-off’ request from the
network hub in hexadecimal format.
XECOM
(11) XE900SL10
11 Page |
Páginas | Total 16 Páginas | |
PDF Descargar | [ Datasheet XE900SL10.PDF ] |
Número de pieza | Descripción | Fabricantes |
XE900SL10 | Miniature Spread Spectrum Transceiver | ![]() Xecom |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
![]() Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
![]() Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |