|
|
PDF CX1599 Data sheet ( Hoja de datos )
| Número de pieza | CX1599 | |
| Descripción | Hydrogen-Filled Ceramic Thyratron | |
| Fabricantes | E2V | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de CX1599 (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
CX1599
Hydrogen-Filled Ceramic Thyratron
The data to be read in conjunction with the Hydrogen
Thyratron Preamble.
ABRIDGED DATA
Hydrogen-filled tetrode thyratron with ceramic envelope,
featuring extremely low jitter, low anode delay time drift and
high rate of rise of current. A hydrogen reservoir operating
from a separate, variable heater supply is incorporated.
CX1599 is a fast, precise switch originally designed for use in
pulse generators to drive Kerr cells, Pockel cells or spark
chambers. Anode voltage must be command charged and
applied for less than 10 ms. The tube geometry allows it to be
mounted in a coaxial housing in order to minimise the total
circuit inductance.
Peak forward anode voltage (see note 1) . 12.5 kV max
Peak anode current . . . . . . . 1000
A max
Anode heating factor . . . . . . 12.5 x 107 VApps max
Peak output power . . . . . . . . . 6.25 MW max
Rate of rise of anode current
(see notes 2 and 3) . . . . . . . . 100
kA/ms
Typical jitter (see note 3) . . . . . . . 0.2
ns
Typical p.r.f. . . . . . . . . . . . 10
Hz
GENERAL
Electrical
Cathode (connected internally
to one end of heater) . . . . . . . . oxide coated
Cathode heater voltage (see note 3) . . .
6.8
+
7
0.0
0.3
Vdc
Cathode heater current . . . . . . . 9.5
A
Reservoir heater voltage
(see note 4) . . . . . . . . . . 4.0 V nom
Reservoir heater current . . . . . . . 1.5
A
Tube heating time (minimum) . . . . . 5.0 minutes
Mechanical
Seated height . . . . . 79.38 mm (3.125 inches) max
Clearance required below
mounting flange . . . . . 31.75 mm (1.250 inches) min
Overall diameter
(mounting flange) . . . 57.15 mm (2.250 inches) nom
Net weight . . . . . . . . 284 g (10 ounces) approx
Mounting position (see note 5) . . . . . . . . . any
Tube connections . . . . . . . . . . . see outline
Cooling . . . . . . . . natural, forced-air or liquid
Where natural cooling is insufficient to maintain the envelope
temperatures below the specified rated values, cooling by
forced-air, or by oil or coolant immersion may be used.
The temperature of the anode terminal and the base, measured
at the points indicated on the outline drawing, must not exceed
the values specified below.
Anode terminal . . . . . . . . . . 250
Base . . . . . . . . . . . . . 220
8C max
8C max
e2v technologies limited, Waterhouse Lane, Chelmsford, Essex CM1 2QU England Telephone: +44 (0)1245 493493 Facsimile: +44 (0)1245 492492
e-mail: [email protected] Internet: www.e2vtechnologies.com Holding Company: e2v holdings limited
e2v technologies inc. 4 Westchester Plaza, PO Box 1482, Elmsford, NY10523-1482 USA Telephone: (914) 592-6050 Facsimile: (914) 592-5148
e-mail: [email protected]
# e2v technologies limited 2004
A1A-CX1599 Issue 4, June 2004
282G/2298
1 page  
OUTLINE
(All dimensions without limits are nominal)
2395C
1C
ANODE CONNECTION FITTED
WITH 8-32 UNC SCREW
SEE NOTE 4
E
A
GRID 2 CONNECTION
2 HOLES 1L
P
J SEE NOTE 2
1D
SEE NOTE 3
GRID 1 CONNECTION
2 HOLES 1M
F
G
MOUNTING FLANGE
SEE NOTE 1
SEE NOTE 5
RESERVOIR HEATER LEAD (RED)
K LONG, TAG TO SUIT 1Q
CATHODE HEATER LEAD (YELLOW)
K LONG, TAG TO SUIT 1Q
8 HOLES 1N
EQUISPACED ON H PCD
1B
Ref Millimetres
Inches
A 76.2 max
B 57.15
C 44.45 + 0.79
D 36.5
E 5.59 + 0.38
F 24.9
G 17.78
H 51.59 + 0.25
J 31.75 min
K 152.4
L 3.05
M 3.05
N 4.19
P 2.54
Q 4.19
3.000 max
2.250
1.750 + 0.031
1.437
0.220 + 0.015
0.980
0.700
2.031 + 0.010
1.250 min
6.000
0.120
0.120
0.165
0.100
0.165
Inch dimensions have been derived from millimetres.
Outline Notes
1. The mounting flange is the connection for the
cathode, cathode heater return and reservoir
heater return.
2. A minimum clearance of 31.75 mm (1.250 inches)
must be allowed below the flange.
3. The recommended mounting hole is 38.1 mm
(1.500 inches) diameter.
4. The anode temperature is measured at the base
of the anode stem.
5. The base temperature is measured at this point.
Whilst e2v technologies has taken care to ensure the accuracy of the information contained herein it accepts no responsibility for the consequences of any use
thereof and also reserves the right to change the specification of goods without notice. e2v technologies accepts no liability beyond that set out in its standard
conditions of sale in respect of infringement of third party patents arising from the use of tubes or other devices in accordance with information contained herein.
# e2v technologies
Printed in England
CX1599, page 5
5 Page | ||
| Páginas | Total 5 Páginas | |
| PDF Descargar | [ Datasheet CX1599.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| CX1594 | Five-Gap Ceramic Thyratron |  ETC |
| CX1599 | Hydrogen-Filled Ceramic Thyratron | E2V |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |