|
|
PDF ENH050Q1-320 Data sheet ( Hoja de datos )
| Número de pieza | ENH050Q1-320 | |
| Descripción | (ENH050Q1-xxx) Color TFT-LCD Module Features GENERAL DESCRIPTION | |
| Fabricantes | WEDC | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ENH050Q1-320 (archivo pdf) en la parte inferior de esta página. Total 21 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
White Electronic Designs
Display Systems Division
ENH050Q1-320/450/600
ENH050Q1-320/450/600 Color TFT-LCD Module Features
GENERAL DESCRIPTION
Slim, lightweight and compact
Panelview provides optically enhanced solutions to the
standard Sharp LQ5AW136 color active matrix LCD
module. The first enhancement is an index matching
(IM) film lamination to the front surface of the display
polarizer.
The IM film is available in two surface treatments - IM/Clear
and IM/110 (a 10% diffusion).The second enhancement is
the incorporation of a reflective polarizer (RP) to improve
brightness by up to 40%. The third enhancement is
the addition of prism films (RPp) further increasing the
brightness of the display. The module accepts full color
video signals conforming to the NTSC(M) and PAL(G-B)
system standards.
It can withstand an intense environment, the online
dimension is suitable for an automotive display, compact
size, compatible with 2DIN size.
Panelview assumes no responsibility for any damage
resulting from the use of the device which does not
comply with the instructions and the precautions specified
in these specification sheets. Panelview does assume the
responsibility for the warranty of the enhanced product.
FEATURES
Dual mode type. [NTSC(M) and PAL(B-G)
standards]
1. Active area/Outline area=70%
2. Thickness: 16.5mm
3. Mass: 185g (Max)
Built-in video interface circuit and control circuit
responsive to two sets of standard RGB analog
video signals.
Reduced refleciton as a resuld of low reflectance
Black-Matrix and Index Matching (IM) film
lamination. IM is available in two surface
treatments, IM/Clear (glossy) and IM/110 (10%
diffusion).
It is possible to use both the simultaneous and the
independent time sampling.
An external clock mode is available.
Optical viewing angle: wide view angle (6 o'clock
direction.) (Customer can use this module as a 12
o'clock viewing direction type by using a display
rotating function to rotate right/left and up/down
scanning direction electrically.)
This module includes a high luminance edge light
that is excellent at low temperature.
It is possible to use the dimming frequency (PWM)
for backlight.
MBK-PAL enables the 234-scanning lines panel to
CONSTRUCTION AND OUTLINE
display a picture with virtually 273-scanning lines.
TFT-active matrix-LCD drive system with high
contrast.
Outline dimensions of TFT-LCD module: See Fig. 3
The module consists of a TFT-LCD panel, driver
IC's control PWB mounted with electronic circuits,
74,800 pixels (RBG Stripe configurations and full
edge light, frame, front and rear shielding cases.
color) 5" diagonal size.
(Backlight driving DC/AC inverter is not built in the
module.)
MECHANICAL SPECIFICATIONS
Parameter
Display Format
Active Area
Screen Size (Diagonal)
Dot Pitch
Dot Configuration
Outline Dimension (1)
Mass
Specifications
74,800
960 (W) x RGB x 234 (H)
102.2 (W) x 74.8 (H)
13 (5")
0.1065 (W) x 0.3195 (H)
RGB Stripe configuration
126.8 (W) x 89.6 (H) x 16.5 (D)
185 (Max)
Units
pixels
dots
mm
cm
mm
-
mm
g
Note: This measurement is typical, and see Fig. 3 for details.
White Electronic Designs Corp. reserves the right to change products or specifications without notice.
Original specifications created by Sharp.
August 2003
Rev. 0
1 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com
1 page  
White Electronic Designs
Display Systems Division
ENH050Q1-320/450/600
TFT-LCD PANEL DRIVING SECTION
Parameter
Symbol
MIN
TYP
MAX
Unit
Remark
DC bias voltage for common electrode driving signal
VCDC
0
+2.0 +3.0
V DC component (15)
Terminal voltage applicable to brightness
VBRT +2.0 +2.3
+2.4
V
Notes:
1. Power supply voltage should not be changed after adjusting VCDC.
2. VR1, VG1, VB1, VR2, VG2, VB2 terminal (Video signal)
3. VBS, VR1, VG1, VB1, VR2, VG2, VB2 terminals
4. HSY, VSY, NTP, VSW, HRV, VRV, SAM CKC, CK terminal
5. HSY, VSY, CK terminals (output mode)
6. CK terminals (output mode)
7. Duty cycle is defined as follows.
tOH tOL
Duty=tOL/tOH
8. VBS (horizontal sync. component)
9. VBS (vertical sync. component)
10. CK (input mode)
11. HSY (input mode)
12. VSY (input mode)
13. In case of cKC='Lo', it shows the phase different from HSY to CK. In that case,
HSY will be taken at the rise timing of CK.
14. In case of CKC='Lo'. it shows the phase difference from VSY to HSY. In that
case, VSY will be taken at the rise timing of HSY.
15. Adjsuting the optimal voltage on every module at the typical value of power
supply voltage to get the maximum value of contrast. However, in the case that
the power supply voltage is changed, for example the level of power supply
voltage is reduced, adjust it externally to get the best contrast with a resistor you
add to this terminal, or semifixed resistor, VCDC, in module. A recommended circuit
is shown in Fig. 5.
Parameter
Lamp Voltage
Lamp current
Lamp frequency
Kickoff voltage
BACKLIGHT DRIVING SECTION
Symbol
MIN
TYP
MAX
VL7 550 610 670
IL 3.0 6.5 7.0
fL 20 -
70
VS -
- 1450
- - 1500
Unit
Vrms
mArms
KHz
Vrms
Vrms
Remark
IL=6.5mArms
normal operation
tA = +25°C
tA = -30°C
POWER COMSUMPTION
tA = 25°C
Parameter
Positive supply current
Negative supply current
Total
Lamp power consumption
Symbol
ISH
ISL
WS
WL
16. Excluding backlight section
17. Reference data by calculation (IL x VL x 1: number of lump)
Conditions
VSH = +8.0V
VSL = -5.0V
normal driving
Circuit Diagram
The circuit block diagram of TFT-LCD module is shown
in Fig. 4.
BRT, VCDC, external adjusting recommended circuit is
shown in Fig. 5.
Caution: Turn the power supply on or off (VSH and VSL)
at the same time. Be careful to supply all power voltage
before inputting signals.
MIN TYP MAX
- 140 170
- 55 70
- 1.4 1.7
- 4.0 -
Unit
mA
mA
W
W
Remark
(16)
(17)
Input/Output Signal Waveforms (Fig. 6)
Caution: For the VBS signal, input standard composite
video (or sync.) signal applicable to the operating mode
which have NTSC (M) or PAL (B-G) and is selected by
the NTP signal.
Dimming Backlight by PWM Timing Chart
If using PWM mode, refer to the timing chart shown in
Fig. 7.
White Electronic Designs Corp. reserves the right to change products or specifications without notice.
Original specifications created by Sharp.
August 2003
Rev. 0
5 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com
5 Page 
White Electronic Designs
Display Systems Division
ENH050Q1-320/450/600
Precautions in Adjusting Module
Variable resistor on the rear face of the module has
been adjusted optimally before shipmetn. Therefore, do
not change any adjusted values. If adjusted values are
changed, the specifications described here may not be
satisfied.
Caution of Product Design
1. The LCD module shall be protected against water by
the waterproof cover.
Others
1. Do not expose the module to direct sunlight or
intensive ultraviolet rays for many hours; liquid crystal
is deteriorated by ultraviolet rays.
2. Store the module at a temperature near room
temperature. When stored at lower than the rated
storage temperature, liquid crystal solidifies, causing
the panel to be damaged. When stored at higher than
the rated storage temperature, liquid crystal turns into
isotropic liquid and may not recover.
3. If LCD panel breaks, the liquid crystal could possibly
escape from the panel. Since the liquid crystal is
injurious, avoid contact with the eyes or mouth. Wash
with soap immediately if contact with the liquid crystal
occurs.
4. Observe all other precautionary requirements in
handling general electronic components.
SHIPPING REQUIREMENTS
Carton storage conditions:
Number of layers of carton in stack: 10 layers max
Environmental conditions:
Temperature:
0~40°C
Humidity:
60%RH or less (at 40°C)
No dew condensation at low temperature and high
humidity,
Atmosphere
Harmful gases such as acid and
alkali which corrode electronic
components and wires must not
be present.
Storage period
Approximately 3 months
Opening of package
To prevent TFT-LCD module from
being damaged by static electricity,
adjust the room humidity to 50%RH
of higher and make certain one is
grounded before opening the
package.
RELIABILITY TEST
Reliability test conditions for the TFT-LCD module are
shown on page 12.
and should be strictly avoided. Image retention may occur
when a fixed pattern is displayed for a long time.
White Electronic Designs Corp. reserves the right to change products or specifications without notice.
Original specifications created by Sharp.
August 2003
Rev. 0
11 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com
11 Page | ||
| Páginas | Total 21 Páginas | |
| PDF Descargar | [ Datasheet ENH050Q1-320.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ENH050Q1-320 | (ENH050Q1-xxx) Color TFT-LCD Module Features GENERAL DESCRIPTION | WEDC |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |