|
|
PDF ADP1610 Data sheet ( Hoja de datos )
| Número de pieza | ADP1610 | |
| Descripción | 1.2 MHz DC-DC Step-Up Switching Converter | |
| Fabricantes | Analog Devices | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ADP1610 (archivo pdf) en la parte inferior de esta página. Total 16 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
1.2 MHz DC-DC Step-Up Switching Converter
ADP1610
FEATURES
Fully integrated 1.2 A , 0.2 Ω, power switch
Pin-selectable 700 kHz or 1.2 MHz PWM frequency
92% efficiency
Adjustable output voltage up to 12 V
3% output regulation accuracy
Adjustable soft start
Input undervoltage lockout
MSOP 8-lead package
APPLICATIONS
TFT LC bias supplies
Portable applications
Industrial/instrumentation equipment
GENERAL DESCRIPTION
The ADP1610 is a dc-to-dc step-up switching converter with an
integrated 1.2 A, 0.2 Ω power switch capable of providing an
output voltage as high as 12 V. With a package height of less that
1.1 mm, the ADP1610 is optimal for space-constrained
applications such as portable devices or thin film transistor
(TFT) liquid crystal displays (LCDs).
The ADP1610 operates in pulse-width modulation (PWM)
current mode with up to 92% efficiency. Adjustable soft start
prevents inrush currents at startup. The pin-selectable switching
frequency and PWM current-mode architecture allow excellent
transient response, easy noise filtering, and the use of small,
cost-saving external inductors and capacitors.
The ADP1610 is offered in the Pb-free 8-lead MSOP and
operates over the temperature range of −40°C to +85°C.
FB 2
RT 7
FUNCTIONAL BLOCK DIAGRAM
REF
COMP
1
ERROR
AMP
gm
IN
6
BIAS
ADP1610
RAMP
GEN
OSC
F/F
RQ
S
COMPARATOR
DRIVER
5 SW
SS 8
SD 3
SOFT START
Figure 1.
CURRENT
SENSE
AMPLIFIER
4
GND
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.326.8703 © 2004 Analog Devices, Inc. All rights reserved.
1 page  
www.DataSheet4U.com
ADP1610
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
COMP 1
FB 2
SD 3
GND 4
ADP1610
TOP VIEW
(Not to Scale)
8 SS
7 RT
6 IN
5 SW
Figure 3. Pin Configuration
Table 3. Pin Function Descriptions
Pin No. Mnemonic Description
1
COMP
Compensation Input. Connect a series resistor-capacitor network from COMP to GND to compensate the
regulator.
2 FB
Output Voltage Feedback Input. Connect a resistive voltage divider from the output voltage to FB to set the
regulator output voltage.
3 SD
Shutdown Input. Drive SD low to shut down the regulator; drive SD high to turn it on.
4 GND Ground.
5 SW
Switching Output. Connect the power inductor from the input voltage to SW and connect the external rectifier
from SW to the output voltage to complete the step-up converter.
6 IN
Main Power Supply Input. IN powers the ADP1610 internal circuitry. Connect IN to the input source voltage.
Bypass IN to GND with a 10 µF or greater capacitor as close to the ADP1610 as possible.
7 RT
Frequency Setting Input. RT controls the switching frequency. Connect RT to GND to program the oscillator to
700 kHz, or connect RT to IN to program it to 1.2 MHz.
8 SS
Soft Start Timing Capacitor Input. A capacitor from SS to GND brings up the output slowly at power-up.
Rev. 0 | Page 5 of 16
5 Page 
www.DataSheet4U.com
ADP1610
Table 4. Inductor Manufacturers
Vendor
Part
Sumida
CMD4D11-2R2MC
847-956-0666
CMD4D11-4R7MC
www.sumida.com
CDRH4D28-100
CDRH5D18-220
CR43-4R7
CR43-100
Coilcraft 847-639-6400 DS1608-472
www.coilcraft.com
DS1608-103
Toko 847-297-0070
D52LC-4R7M
www.tokoam.com
D52LC-100M
L (µH)
2.2
4.7
10
22
4.7
10
4.7
10
4.7
10
Using the duty cycle and switching frequency, fSW, determine the
on-time by the following equation:
tON = D
f SW
(4)
The inductor ripple current (∆IL) in steady state is
∆IL = VIN × tON
L
(5)
Solving for the inductance value, L,
L = VIN × t ON
∆I L
(6)
Make sure that the peak inductor current (the maximum input
current plus half the inductor ripple current) is below the rated
saturation current of the inductor. Likewise, make sure that the
maximum rated rms current of the inductor is greater than the
maximum dc input current to the regulator.
For duty cycles greater than 50%, which occur with input
voltages greater than one-half the output voltage, slope
compensation is required to maintain stability of the current-
mode regulator. For stable current-mode operation, ensure that
the selected inductance is equal to or greater than LMIN:
L > LMIN
=
VOUT −VIN
1.8 A × f SW
(7)
CHOOSING THE INPUT AND OUTPUT CAPACITORS
The ADP1610 requires input and output bypass capacitors to
supply transient currents while maintaining constant input and
output voltage. Use a low ESR (equivalent series resistance),
10 µF or greater input capacitor to prevent noise at the
ADP1610 input. Place the capacitor between IN and GND as
close to the ADP1610 as possible. Ceramic capacitors are
preferred because of their low ESR characteristics. Alternatively,
use a high value, medium ESR capacitor in parallel with a 0.1 µF
low ESR capacitor as close to the ADP1610 as possible.
Max DC Current
0.95
0.75
1.00
0.80
1.15
1.04
1.40
1.00
1.14
0.76
Max DCR (mΩ)
116
216
128
290
109
182
60
75
87
150
Height (mm)
1.2
1.2
3.0
2.0
3.5
3.5
2.9
2.9
2.0
2.0
The output capacitor maintains the output voltage and supplies
current to the load while the ADP1610 switch is on. The value
and characteristics of the output capacitor greatly affect the
output voltage ripple and stability of the regulator. Use a low
ESR output capacitor; ceramic dielectric capacitors are
preferred.
For very low ESR capacitors such as ceramic capacitors, the
ripple current due to the capacitance is calculated as follows.
Because the capacitor discharges during the on-time, tON, the
charge removed from the capacitor, QC, is the load current
multiplied by the on-time. Therefore, the output voltage ripple
(∆VOUT) is
∆VOUT
= QC
COUT
= I L ×tON
COUT
(8)
where:
COUT is the output capacitance,
IL is the average inductor current,
t ON
=
D
f SW
(9)
and
D = VOUT −VIN
VOUT
(10)
Choose the output capacitor based on the following equation:
COUT
≥
I L ×(VOUT −VIN )
f SW ×VOUT × ∆VOUT
(11)
Table 5. Capacitor Manufacturers
Vendor
Phone No.
AVX 408-573-4150
Murata
714-852-2001
Sanyo
408-749-9714
Taiyo–Yuden 408-573-4150
Web Address
www.avxcorp.com
www.murata.com
www.sanyovideo.com
www.t-yuden.com
Rev. 0 | Page 11 of 16
11 Page | ||
| Páginas | Total 16 Páginas | |
| PDF Descargar | [ Datasheet ADP1610.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ADP161 | CMOS Linear Regulators | Analog Devices |
| ADP1610 | 1.2 MHz DC-DC Step-Up Switching Converter | Analog Devices |
| ADP1611 | 1.2 MHz Step-Up DC-to-DC Switching Converter | Analog Devices |
| ADP1612 | (ADP1612 / ADP1613) 650 KHz /1.3 MHz Step-Up PWM DC-to-DC Switching Converter | Analog Devices |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |