DataSheet.es    


PDF MC74AC4040 Data sheet ( Hoja de datos )

Número de pieza MC74AC4040
Descripción 12-STAGE BINARY RIPPLE COUNTER
Fabricantes Motorola Semiconductors 
Logotipo Motorola Semiconductors Logotipo



Hay una vista previa y un enlace de descarga de MC74AC4040 (archivo pdf) en la parte inferior de esta página.


Total 5 Páginas

No Preview Available ! MC74AC4040 Hoja de datos, Descripción, Manual

www.DataSheet4U.com
MC74AC4040
12ĆStage Binary Ripple Counter
The MC74AC4040 consists of 12 master-slave flip-flops. The output of each
flip-flop feeds the next and the frequency at each output is half that of the preceding
one. The state of the counter advances on the negative-going edge of the Clock
input. Reset is asynchronous and active-high.
State changes of the Q outputs do not occur simultaneously because of internal
ripple delays. Therefore, decoded output signals are subject to decoding spikes
and may have to be gated with the Clock of the MC74AC4040 for some designs.
140 MHz Typ. Clock
Outputs Source/Sink 24 mA
Operating Voltage Range: 2.0 to 6.0 V
High Noise Immunity
VCC Q11 Q10 Q8 Q9 RESET CLK Q1
16 15 14 13 12 11 10 9
12-STAGE
BINARY RIPPLE
COUNTER
N SUFFIX
CASE 648-08
PLASTIC
12345678
Q12 Q6 Q5 Q7 Q4 Q3 Q2 GND
FUNCTION TABLE
Clock Reset
L
L
XH
Output State
No Change
Advance to next state
All Outputs are low
D SUFFIX
CASE 751B-05
PLASTIC
LOGIC DIAGRAM
10
CLOCK
11
RESET
PIN 16 = VCC
PIN 8 = GND
9
Q1
7
Q2
6
Q3
5
Q4
3
Q5
2
Q6
4
Q7
13
Q8
12
Q9
14
Q10
15
Q11
1
Q12
DataSheet4 U .com
FACT DATA
5-1

1 page




MC74AC4040 pdf
www.DataSheet4U.com
–A–
16
1
H
G
MC74AC4040
OUTLINE DIMENSIONS
9
B
8
N SUFFIX
PLASTIC DIP PACKAGE
CASE 648–08
ISSUE R
FC
S
L
–T–
SEATING
PLANE
KJ
D 16 PL
0.25 (0.010) M T A M
M
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
INCHES
MILLIMETERS
DIM MIN MAX MIN MAX
A 0.740 0.770 18.80 19.55
B 0.250 0.270 6.35 6.85
C 0.145 0.175 3.69 4.44
D 0.015 0.021 0.39 0.53
F 0.040 0.70 1.02 1.77
G 0.100 BSC
2.54 BSC
H 0.050 BSC
1.27 BSC
J 0.008 0.015 0.21 0.38
K 0.110 0.130 2.80 3.30
L 0.295 0.305 7.50 7.74
M 0_ 10_ 0 _ 10 _
S 0.020 0.040 0.51 1.01
–A–
16
1
D SUFFIX
PLASTIC SOIC PACKAGE
CASE 751B–05
ISSUE J
9
–B– P 8 PL
8 0.25 (0.010) M B S
G
–T– SEATING
PLANE
K
C
D 16 PL
0.25 (0.010) M T B S A S
R X 45_
F
MJ
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
MILLIMETERS
INCHES
DIM MIN MAX MIN MAX
A 9.80 10.00 0.386 0.393
B 3.80 4.00 0.150 0.157
C 1.35 1.75 0.054 0.068
D 0.35 0.49 0.014 0.019
F 0.40 1.25 0.016 0.049
G 1.27 BSC
0.050 BSC
J 0.19 0.25 0.008 0.009
K 0.10 0.25 0.004 0.009
M 0_ 7_ 0_ 7_
P 5.80 6.20 0.229 0.244
R 0.25 0.50 0.010 0.019
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,
and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different
applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in
systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
How to reach us:
USA/EUROPE: Motorola Literature Distribution;
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki,
6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315
MFAX: [email protected] –TOUCHTONE (602) 244–6609
INTERNET: http://Design–NET.com
HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
DataSheet4 U .com
*MC74AC4040/D*FACT DATA
5-5
MC74AC4040/D

5 Page










PáginasTotal 5 Páginas
PDF Descargar[ Datasheet MC74AC4040.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
MC74AC404012-STAGE BINARY RIPPLE COUNTERMotorola Semiconductors
Motorola Semiconductors
MC74AC404012-Stage Binary Ripple CounterON Semiconductor
ON Semiconductor

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar