DataSheet.es    


PDF AH212 Data sheet ( Hoja de datos )

Número de pieza AH212
Descripción 1 Watt High Linearity / High Gain InGaP HBT Amplifier
Fabricantes ETC 
Logotipo ETC Logotipo



Hay una vista previa y un enlace de descarga de AH212 (archivo pdf) en la parte inferior de esta página.


Total 5 Páginas

No Preview Available ! AH212 Hoja de datos, Descripción, Manual

www.DataSheet4U.com
AH212
The Communications Edge TM
1 Watt High Linearity, High Gain InGaP HBT Amplifier
Product Information
Product Features
Product Description
Functional Diagram
x 1800 – 2200 MHz
x 26 dB Gain
x +30 dBm P1dB
x +46 dBm Output IP3
x +5V Single Positive Supply
x Internal Active Bias
x Lead-free/green/RoHS-compliant
SOIC-8 Package
Applications
x Mobile Infrastructure
The AH212 is a high dynamic range two-stage driver
amplifier in a low-cost surface mount package. The
InGaP/GaAs HBT is able to achieve superior performance
for various narrowband-tuned application circuits with up
to +46 dBm OIP3 and +30 dBm of compressed 1-dB
power. The amplifier is housed in an industry-standard
SMT lead-free/green/RoHS-compliant SOIC-8 package.
All devices are 100% RF and DC tested.
The product is targeted for use as linear driver amplifier for
various current and next generation wireless technologies
such as GPRS, GSM, CDMA, W-CDMA, and UMTS,
where high linearity and high power is required. The
internal active bias allows the AH212 to maintain high
linearity over temperature and operate directly off a +5 V
supply.
Vc1 1
8 N/C
Vbias1 2
7 Vcc2 / RF Out
RF In 3
6 Vcc2 / RF Out
Vbias2 4
5 N/C
AH212-S8G
Function
Vc1
Input
Output
Vbias1
Vbias2
Vcc2
GND
N/C or GND
Pin No.
1
3
6, 7
2
4
6, 7
Backside Paddle
5, 8
Specifications (1)
Typical Performance (1)
Parameters
Operational Bandwidth
Test Frequency
Gain
Input Return Loss
Output Return Loss
Output P1dB
Output IP3 (2)
Noise Figure
W-CDMA Channel Power
@ -45 dBc ACLR
Operating Current Range , Icc
Device Voltage, Vcc
Units
MHz
MHz
dB
dB
dB
dBm
dBm
dB
dBm
mA
V
Min
1800
Typ Max Parameters
2200
Frequency
2140
Gain
25 Input Return Loss
25 DataSheet4UOu.ctpoumt Return Loss
9 Output P1dB
+29.5
Output IP3
+46 IS-95A Channel Power
6.0
@ -45 dBc ACPR
W-CDMA Channel Power
+21
@ -45 dBc ACLR
400
5
Noise Figure
Supply Bias
1. Test conditions unless otherwise noted: 25ºC, +5V, in tuned application circuit.
2. 3OIP measured with two tones at an output power of +15 dBm/tone separated by 1 MHz. The
suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule.
Units
MHz
dB
dB
dB
dBm
dBm
dBm
dBm
dB
Typical
1960
2140
25.8 25.0
15 25
11 9
+30 +29.5
+48.5
+46
+23.5
+21
5.5 6.0
+5 V @ 400 mA
DataShee
Absolute Maximum Rating
Parameter
Operating Case Temperature
Storage Temperature
RF Input Power (continuous)
Device Voltage
Device Current
Device Power
DataSheet4UJu.cnoctmion Temperature
Rating
-40 to +85 qC
-65 to +150 qC
+26 dBm
+7 V
900 mA
6W
+250 ºC
Ordering Information
Part No.
AH212-S8G
AH212-S8PCB1960
AH212-S8PCB2140
Description
1 Watt, High Gain InGaP HBT Amplifier
(lead-free/green/RoHS-compliant SOIC-8 Package)
1960 MHz Evaluation Board
2140 MHz Evaluation Board
Operation of this device above any of these parameters may cause permanent damage.
       WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: [email protected]
DataSheet4 U .com
Specifications and information are subject to change without notice.
Web site: www.wj.comDataSheet4U.com
Page 1 of 5 November 2005

1 page




AH212 pdf
www.DataSheet4U.com
AH212
The Communications Edge TM
1 Watt High Linearity, High Gain InGaP HBT Amplifier
Product Information
AH212-S8G (Lead-Free SOIC-8 Package) Mechanical Information
This package is lead-free/green/RoHS-compliant. The plating material on the leads is NiPdAu. It is compatible with both lead-free
(maximum 260qC reflow temperature) and lead (maximum 245qC reflow temperature) soldering processes.
Outline Drawing
Product Marking
The component will be marked with an
“AH212G” designator with an alphanumeric lot
code on the top surface of the package.
Tape and reel specifications for this part are
located on the website in the “Application
Notes” section.
ESD / MSL Information
et4U.com
DataSheet4U.com
Mounting Configuration / Land Pattern
ESD Rating:
Value:
Test:
Standard:
¦Class 1B
Passes 500V to <1000V
Human Body Model (HBM)
JEDEC Standard JESD22-A114
ESD Rating: Class IV
Value:
Passes §©¨ !
Test: Charged Device Model (CDM)
Standard: JEDEC Standard JESD22-C101
"MSL Rating: Level 2 at +260 C convection reflow
Standard: JEDEC Standard J-STD-020
Mounting Config. Notes
1. A heatsink underneath the area of the PCB for the mounted device
is recommended for proper thermal operation. Damage to the
device can occur without the use of one.
2. Ground / thermal vias are critical for the proper performance of this
device. Vias should use a .35mm (#80 / .0135” ) diameter drill and
have a final plated thru diameter of .25 mm (.010” ).
3. Add as much copper as possible to inner and outer layers near the
part to ensure optimal thermal performance.
4. Mounting screws can be added near the part to fasten the board to a
heatsink. Ensure that the ground / thermal via region contacts the
heatsink.
5. Do not put solder mask on the backside of the PC board in the
region where the board contacts the heatsink.
6. RF trace width depends upon the PC board material and
construction.
7. Use 1 oz. Copper minimum.
8. All dimensions are in millimeters
Thermal Specifications
Parameter
Rating
Operating Case Temperature
-40 to +85q C
Thermal Resistance (1), Rth
33 q C / W
Junction Temperature (2), Tjc
156 q C
Notes:
¥1. The thermal resistance is referenced from the junction-to-case at a case
temperature of 85 C. Tjc is a function of the voltage and the current applied.
It can be calculated by:
Tjc = Tcase + Rth * Vcc * Icc
¥2. This corresponds to the typical biasing condition of +5V, 400 mA at an 85 C
DataSheet4U.comcase temperature.
¤ ¤ ¤ ¤WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: [email protected]
DataSheet4 U .com
Specifications and information are subject to change without notice.
Web site: www.wj.comDataSheet4U.com
Page 5 of 5 November 2005

5 Page










PáginasTotal 5 Páginas
PDF Descargar[ Datasheet AH212.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
AH211TWO PHASE HALL EFFECT LATCHBCD Semiconductor
BCD Semiconductor
AH211AMercury Vapour RectifierITT
ITT
AH2121 Watt High Linearity / High Gain InGaP HBT AmplifierETC
ETC
AH213RectifierMarconi
Marconi

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar