DataSheet.es    


PDF IR3088 Data sheet ( Hoja de datos )

Número de pieza IR3088
Descripción XPHASE PHASE IC WITH FAULT AND OVERTEMP DETECT
Fabricantes International Rectifier 
Logotipo International Rectifier Logotipo



Hay una vista previa y un enlace de descarga de IR3088 (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! IR3088 Hoja de datos, Descripción, Manual

www.DataSheet4U.com
NOT RECOMMENDED FOR NEW
DESIGNS. REPLACE WITH IR3088A
Data Sheet No. PD94712
IR3088
XPHASETM PHASE IC WITH FAULT AND OVERTEMP DETECT
DESCRIPTION
The IR3088 Phase IC combined with an IR XPhaseTM Control IC provides a full featured and flexible way to
implement power solutions for the latest high performance CPUs and ASICs. The “Control” IC provides
overall system control and interfaces with any number of “Phase” ICs which each drive and monitor a single
phase of a multiphase converter. The XPhaseTM architecture results in a power supply that is smaller, less
expensive, and easier to design while providing higher efficiency than conventional approaches.
The IR3088 is intended for the following application conditions:
Excessive impedance between converter and load
Output voltage exceeding the control IC reference/VID voltage
FEATURES
2.5A Average Gate Drive Current
Loss-Less Inductor Current Sense
Internal Inductor DCR Temperature Compensation
Programmable Phase Delay
Programmable Feed-Forward Voltage Mode PWM Ramp
Sub 100ns Minimum Pulse Width supports 1MHz per-phase operation
Current Sense Amplifier drives a single wire Average Current Share Bus
DataShee
Current Share Amplifier reduces PWDMataRSahmepets4loUp.ceotmo ensure sharing between phases
Body BrakingTM disables Synchronous MOSFET for improved transient response and prevents negative
output voltage at converter turn-off
Phase Fault Detection
Programmable Phase Over-Temperature Detection
Control FET driver’s 25V input voltage capability simplifies boot-strap supply design
Small thermally enhanced 20L MLPQ package
PACKAGE PINOUT
1 RMPIN+
2 RMPIN-
3 HOTSET
4 VRHOT
5 ISHARE
IR3088
PHASE
IC
VCCH
GATEH
PGND
GATEL
VCCL
15
14
13
12
11
DataSheet4U.com
Page 1 of 34
DataSheet4 U .com
DataSheet4U.com
9/30/04

1 page




IR3088 pdf
www.DataSheet4U.com
IR3088
PARAMETER
General
VCC Supply Current
VCCL Supply Current
VCCH Supply Current
BIASIN Bias Current
DACIN Bias Current
TEST CONDITION
6V VCCH 14V
14V VCCH 25V
Note 1: Guaranteed by design, but not tested in production
MIN TYP MAX UNIT
10 14 mA
2.5 5 mA
5.5 8 mA
6.5 10 mA
-5 -2.5 2
µA
-2 -0.5 1
µA
PIN DESCRIPTION
et4U.com
PIN#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
DataSheet4U.com
PIN SYMBOL PIN DESCRIPTION
RMPIN+ Non-inverting input to Ramp Comparator
RMPIN- Inverting input to Ramp Comparator
HOTSET
Inverting input to VRHOT comparator. Connect resistor divider from VBIAS to LGND
to program VRHOT threshold. Diode or thermistor may be substituted for lower
resistor for enhanced/remote temperature sensing.
VRHOT
Open Collector output of the VRHOT comparator which drives low if IC junction
temperature exceeds the user programmable limit. Connect external pull-up.
DataShee
ISHARE
Output of the CuDrraetnatSSheenest4eUA.mcopmlifier and input to the Share Adjust Error Amplifier.
Voltage on this pin is equal to V(DACIN) + 34 * [V(CSIN+) – V(CSIN-)]. Connecting
ISHARE pins together creates a Share Bus enabling current sharing between Phase
ICs. The Share bus is also used by the Control IC for voltage positioning and Over-
Current protection.
SCOMP
Compensation for the Current Share control loop. Connect a capacitor to ground to se
the control loop’s bandwidth.
EAIN
PWM comparator input from the error amplifier output of Control IC. Both Gate Driver
outputs drive low if the voltage on this pin is less than 91% of V(DACIN).
PWMRMP PWM comparator ramp input. Connect a resistor from this pin to the converter input
voltage and a capacitor to LGND to program the PWM ramp.
LGND
Signal ground and IC substrate connection
VCC
Power for internal circuitry
VCCL
Power for Low-Side Gate Driver
GATEL Low-Side Gate Driver Output and input to GATEH non-overlap comparator
PGND
Return for Gate Drivers
GATEH High-Side Gate Driver Output and input to GATEL non-overlap comparator
VCCH
Power for High-Side Gate Driver
CSIN+ Non-inverting input to the Current Sense Amplifier
CSIN-
Inverting input to the Current Sense
PHSFLT
Open Collector output of the Phase Fault comparator. Drives low if Phase current is
unable to match the level of the SHARE bus due to an external fault. Connect externa
pull-up.
DACIN
Reference voltage input from the Control IC. Current sensing and PWM operation
referenced to this pin.
BIASIN System reference voltage for internal circuitry
Page 5 of 34
DataSheet4 U .com
DataSheet4U.com
9/30/04

5 Page





IR3088 arduino
www.DataSheet4U.com
IR3088
IR3088 THEORY OF OPERATION
Block Diagram
The Block diagram of the IR3088 is shown in Figure 6, and specific features are discussed in the following sections.
et4U.com
RMPIN+
RMPIN-
EAIN
BIASIN
PWMRMP
SCOMP
ISHARE
LGND
VRHOT
HOTSET
RAMP
COMPARATOR
CLOCK
PULSE
GENERATOR
PWM
COMPARATOR
-
SYSTEM
REFERENCE
VOLTAGE
+
ENABLE
PWM
LATCH
S
RESET
DOMINANT
R
RAMP
SLOPE
ADJUST
RAMP
DISCHARGE
CLAMP
-
GATE
+
NON-OVERLAP
COMPARATORS
SHARE
ADJUST
ERROR
AMP
+
X
0.91
0% DUTY
CYCLE
COMPARATOR
10K 20mV
-
VRHOT
COMPARATOR
+
+
DataSheet4U.com
+ VOLTAGE
PROPORTIONAL
TO ABSOLUTE
- TEMPERATURE
FAULT
COMPARATOR
2V
INTERNAL
CIRCUIT
BIAS
CURRENT
SENSE
AMP
X34
VCCH
GATEH
VCCL
GATEL
PGND
VCC
DACIN
CSIN+
CSIN-
PHSFLT
DataShee
Figure 6. IR3088 Block Diagram
Tri-State Gate Drivers
The gate drivers can deliver up to 3A peak current. An adaptive non-overlap circuit monitors the voltage on the
GATEH and GATEL pins to prevent MOSFET shoot-through current while minimizing body diode conduction.
An Enable signal is provided by the Control IC to the Phase IC without the addition of a dedicated signal line. The
Error Amplifier output of the Control IC drives low in response to any fault condition such as input under voltage or
output overload. The IR3088 0% duty cycle comparator detects this and drives both gate outputs low. This tri-state
operation prevents negative inductor current and negative output voltage during power-down.
The Gate Drivers revert to a high impedance “off” state if VCCL and VCCH supply voltages are below the normal
operating range. An 80kresistor is connected across the GATEH/GATEL and PGND pins to prevent the
GATEH/GATEL voltage from rising due to leakage or other causes under these conditions.
Thermal Monitoring (VRHOT)
The IR3088 senses its own die temperature and produces a voltage at the input of the VRHOT comparator that is
proportional to temperature. An external resistor divider connected from VBIAS to the HOTSET pin and ground can
be used to program the thermal trip point of the VRHOT comparator. The VRHOT pin is an open-collector output
and should be pulled up to a voltage source through a resistor. If the thermal trip point is reached the VRHOT output
DataSheet4Udr.icvoems low.
Page 11 of 34
DataSheet4 U .com
DataSheet4U.com
9/30/04

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet IR3088.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
IR3080XPHASE VRD10 CONTROL IC WITH VCCVID & OVERTEMP DETECTInternational Rectifier
International Rectifier
IR3080PBFXPHASETM VRD10 CONTROL ICInternational Rectifier
International Rectifier
IR3081XPHASE VR 10.0 CONTROL ICInternational Rectifier
International Rectifier
IR3081AXPHASETM VR 10 CONTROL ICInternational Rectifier
International Rectifier

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar