|
|
PDF DMC-50448N Data sheet ( Hoja de datos )
| Número de pieza | DMC-50448N | |
| Descripción | LCD Module Specification | |
| Fabricantes | OPTREX CORPORATION | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de DMC-50448N (archivo pdf) en la parte inferior de esta página. Total 15 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
LCD Module Specification
Type No. ＤＭＣ－５０４４８Ｎ
First Edition
Approved by
July 19, 1994
Checked by
Final Revision
Checked by
December 18, 1997
Prepared by
Production Div.
Quality Assurance Div.
Design Engineering Div.
Production Div.
Table of Contents
1. General Specifications .............................................................................2
2. Electrical Specifications...........................................................................3
3. Optical Specifications ..............................................................................5
4. I/O Terminal.............................................................................................7
5. Test............................................................................................................9
6. Appearance Standards............................................................................10
7. Code System of Production Lot ..........................................................13
8. Type Number..........................................................................................13
9. Applying Precautions .............................................................................13
10. Precautions Relating Product Handling................................................14
11. Warranty..................................................................................................15
Revision History
www.DataSheet4U.comRev. Date
Page
Comment
2 December 18, 1997
2 Change of maximum compornents line. ( UE-35395B→C )
DMC-50448N (AA) No.99-0094
OPTREX CORPORATION
OPTREX
Page 1/15
www.DataSheet4U.com
1 page  
www.DataSheet4U.com
3.Optical Specifications
3.1.LCD Driving Voltage
Parameter
Symbol
Conditions
Min. Typ. Max. Units
Recommended
Ta= 0℃
－ － 4.8 V
LCD Driving Voltage
VDD-V0
Ta=25℃
3.9 4.2 4.5
V
Note 1
Ta=50℃
3.6 － － V
Note 1 : Voltage (Applied actual waveform to LCD Module) for the best contrast. The range of
minimum and maximum shows tolerance of the operating voltage. The specified contrast ratio and
response time are not guaranteed over the entire range.
3.2.Optical Characteristics
Ta=25℃, 1/16 Duty, 1/4 Bias, VD=4.2V (Note 4), θ= 0 ﾟ, φ=－ﾟ
Parameter
Symbol
Conditions
Min. Typ. Max. Units
Contrast Ratio
Note 1
CR
θ= 0 ﾟ, φ=－ﾟ
－
7
－
Viewing Angle
Shown in 3.3
Response Rise Note 2
TON
－ － 130 200 ms
Time Decay Note 3
TOFF
－ － 130 200 ms
Note 1 : Contrast ratio is definded as follows.
CR = LOFF / LON
LON : Luminance of the ON segments
www.DataSheet4U.comLOFF : Luminance of the OFF segments
Note 2 : The time that the luminance level reaches 90% of the saturation level from 0% when ON
signal is applied.
Note 3 : The time that the luminance level reaches 10% of the saturation level from 100% when OFF
signal is applied.
Note 4 : Definition of Driving Voltage VD
Assuming that the typical driving waveforms shown below are applied to the LCD Panel at
1/A Duty - 1/B Bias ( A : Duty Number, B : Bias Number ). Driving voltage VD is definded
as follows.
VD = (Vth1+Vth2) / 2
Vth1 : The voltage VO-P that should provide 50% of the saturation level in the luminance at
the segment which the ON signal is applied to.
Vth2 : The voltage VO-P that should provide 50% of the saturation level in the luminance at
the segment which the OFF signal is applied to.
VO-P
1 / ( fF×A )
〈ON SIGNAL〉
DMC-50448N (AA) No.99-0094
1 / fF
( B-2 )×VO-P / B
〈OFF SIGNAL〉
OPTREX CORPORATION
OPTREX
Page 5/15
www.DataSheet4U.com
5 Page 
www.DataSheet4U.com
6.3.Standards
No. Parameter
Criteria
1 Black and
(1) Round Shape
White Spots,
Zone
Acceptable Number
Foreign Substances
Dimension (mm)
ABC
D ≦ 0.1
*
*
*
0.1 ＜ D ≦ 0.2
5
5
*
0.2 ＜ D ≦ 0.3
0
1
*
0.3 ＜ D
00*
D = ( Long + Short ) / 2 * : Disregard
(2) Line Shape
Zone
Acceptable Number
X(mm) Y(mm)
ABC
－
2.0≧L
1.0≧L
1.0≧L
－
0.02≧W
0.03≧W
0.04≧W
0.05≧W
0.05＜W
***
33*
12*
02*
In the same way (1)
X : Length Y : Width * : Disregard
www.DataSheet4U.comTotal defects shall not exceed 5.
2 Air Bubbles
(between glass
Zone
Acceptable Number
& polarizer)
Dimension (mm)
ABC
D ≦0.15
*
*
*
0.15＜ D ≦0.3 2 3 *
0.3 ＜ D ≦0.5 1 2 *
0.5 ＜ D ≦1.0 0 1 *
* : Disregard
Total defects shall not exceed 3.
DMC-50448N (AA) No.99-0094
OPTREX CORPORATION
OPTREX
Page 11/15
www.DataSheet4U.com
11 Page | ||
| Páginas | Total 15 Páginas | |
| PDF Descargar | [ Datasheet DMC-50448N.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| DMC-50448 | LCD Module | OPTREX CORPORATION |
| DMC-50448N | LCD Module Specification | OPTREX CORPORATION |
| DMC-50448N | LCD Module Specification |  OPTEK Technologies |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |