DataSheet.es    


PDF KRC-PS978R Data sheet ( Hoja de datos )

Número de pieza KRC-PS978R
Descripción (KRC-xxx) Cassette Receiver
Fabricantes Kenwood 
Logotipo Kenwood Logotipo



Hay una vista previa y un enlace de descarga de KRC-PS978R (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! KRC-PS978R Hoja de datos, Descripción, Manual

KRC-PS978R
KRC-878R
KRC-778R
KRC-778RV
CASSETTE RECEIVER
INSTRUCTION MANUAL
B64-1612-00 (EN)

1 page




KRC-PS978R pdf
Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get
dirty, wipe them with a dry, soft cloth.
Cleaning the Unit
If the front panel gets dirty, turn off the
power and wipe the panel with a dry silicon
cloth or soft cloth.
2CAUTION
Do not wipe the panel with a stiff cloth or a
cloth dampened by volatile solvents such as
paint thinner and alcohol. They can scratch
the surface of the panel and/or cause the
indicator letters to peel off.
Cleaning the Tape Head
After you have used the tape player many
times over a long period, magnetic powder
from the tapes and dust accumulates on the
tape head, causing noise and a deterioration
in sound quality. Clean the tape head using a
cleaning tape or cleaning kit designed for use
in car audio systems.
Handling Cassette Tapes
• Do not play a cassette whose tape has gone
slack. In such a case, wind it tight using a
pencil or the like in one of the spools.
Playing slack cassette tapes can result in the
tape tangling around the capstan and/or
pinch rollers, causing trouble.
• Do not play a deformed cassette or one
whose label is starting to come off, as it can
cause the unit to malfunction.
• Do not leave tapes in hot places, such as
above the fascia panel (dashboard) and other
spots exposed to direct sunlight, or near
heater outlets. They can deform the
cassette.
• Avoid using extremely long cassette tapes,
such as 100-minute-long tapes. Such tapes
are very thin, and can tangle easily around
the pinch rollers or other parts inside the
unit, causing unit failure.
• Remove a cassette tape from the unit when
not listening to it for a whilst. If you leave a
tape in the unit too long, it may stick to the
tape head and cause unit malfunction.
—5—

5 Page





KRC-PS978R arduino
• The faceplate is a precision piece of equipment and can be
damaged by shocks or jolts. For that reason, keep the faceplate
in its special storage case whilst detached.
• Do not expose the faceplate or its storage case to direct
sunlight or excessive heat or humidity. Also avoid places with
too much dust or the possibility of water splashing.
Reattaching the Faceplate:
1 Hold the faceplate so that the control panel faces the front
toward you and set the left side of the faceplate in the
faceplate bracket.
2CAUTION
Do not set the right side of the faceplate in the faceplate bracket
first, when reattaching the faceplate. Doing so may cause the
connector on the faceplate bracket to malfunction.
2 Press the right side of the faceplate until it locks.
Please refer to the following for the contents of the
adjustment modes.
NOTE Source tone memory
Each source (tape, CD, FM, AM, and disc changer) has its own
memory in which to store the bass, treble and N-F level settings.
The settings made for a particular source are then recalled
automatically whenever you use that source (e.g., FM mode uses
the tone settings made for FM, AM for AM, etc.).
3 Adjust each mode
Press the 4/¢ button.
Look at the table to adjust the mode being displayed.
4 Press the AUD button to end the control mode.
NOTE
If the faceplate bracket's angle was not set to the vertical when
the faceplate was mounted, check that the faceplate is securely
attached to the faceplate bracket by holding its right side and
pulling it gently towards you.
"Kex"/"ec4"/"dB" : Recalling the kenwood preset sound setting
Press the preset buttons (#1-6).
Settings: #1;Flat, #2;Rock, #3;Pops/Top40, #4;Jazz, #5;Easy,
#6;Scan of #1-5
NOTE
• This mode is available only when the Sound coordinate system
is on. (page33)
• You can call the following settings with this function; bass
centre frequency, bass level, bass quality factor, bass
extension, treble centre frequency, and treble level setting.
Their setting values are different depending on the setting of
the mobile preset plan mode.
Audio Control Setting
Adjust various parameters of sound quality.
1 Press the AUD button to enter the control mode.
2 Selecting mode
Press either the FM or AM button.
Each time the button is pressed, the adjustment mode will
change.
— 11 —

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet KRC-PS978R.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
KRC-PS978R(KRC-xxx) Cassette ReceiverKenwood
Kenwood

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar