|
|
Número de pieza | FTM-9412P-K10E | |
Descripción | (FTM-9412P-x10xx) SFF GE-PON Px10 ONU Transceiver | |
Fabricantes | Fiberxon | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de FTM-9412P-K10E (archivo pdf) en la parte inferior de esta página. Total 15 Páginas | ||
No Preview Available ! Aug.9, 2005
SFF GE-PON PX10 ONU Transceiver
FTM-9412P-F10/F10E/F10i/F10U/F10DC
FTM-9412P-K10/K10E/K10i/K10U/K10DC
(IEEE 802.3ah™-2004 1000BASE-PX10-U)
Standard
Members of FlexonTM Family
Features
Single fiber bi-directional data links with symmetric
1.25Gbps upstream and 1.25Gbps downstream
Integrated with micro-optics WDM filter for dual
wavelength Tx/Rx operation at 1310/1490nm
1310nm burst-mode transmitter with FP laser
1490nm continuous-mode receiver with PIN-TIA
and optional 1550nm optical signal rejection
Different operating temperature class
0 to 70℃ Standard Class
-20 to 70℃ Extended Class
-40 to 85℃ Industrial Class
2× 5 /2×1 0 SF F package with SC/UPC pigtail
Single 3.3V power supply
LVPECL compatible data input/output interface
LVTTL transmitter burst-mode control
LVTTL transmitter disable control(2× 10 SFF)
LVTTL transmitter laser failure alarm(2×1 0 S FF )
LVTTL receiver signal-detected indication
Low EMI and excellent ESD protection
Class I laser safety standard IEC-60825 compliant
Applications
Compliant with SFF MSA
Compliant with IEEE Std 802.3ah™ -2004
1000BASE-PX10-U
Compliant with FCC 47 CFR Part 15, Class B
Compliant with FDA 21 CFR 1040.10 and 1040.11,
Class I
Description
2× 5 /2×1 0 SFF GE-PON PX10 ONU transceiver family
is Optical Network Unit (ONU) for IEEE802.3ah™-2004
1000BASE-PX10-U application
The transceiver is the high performance module for
1.25Gbps data link in single fiber by using 1310nm
burst-mode transmitter and 1490nm continuous-mode
receiver with optional 1550nm optical signal rejection.
The transmitter section uses a multiple quantum well
1310nm FP laser and is ClassⅠlaser compliant product
according to international safety standard IEC-60825.
The receiver section uses an integrated 1490nm PIN
and preamplifier mounted in an optical header and
limiting post-amplifier IC.
The optical burst output can be enabled by a LVTTL
logic high-level input of TX_BRST. Singal Detected (SD)
output is provided to indicate the detection of an input
optical signal of receiver.
Gigabit Ethernet Passive Optical Networks
For 2× 10 SF F ,optical output can be disabled by a
(GE-PON) – ONU side
LVTTL logic high-level input of TX_DIS, and LAS_nFAIL
Gigabit Ethernet Point-to-Point Bi-directional
is provided to indicate that degradation of the laser.
Transmission
Media Converts for Fiber-In-The-Loop (FITL)
www.DataSheet4U.com
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute
Doc No: DS3493000-3a
www.DataSheet4U.com
Page 1 of 15
www.DataSheet4U.com
1 page SFF GE-PON PX10 ONU Transceiver
10km transmission
FTM-9412P-F10/F10E/F10i/F10U/F10DC
FTM-9412P-K10/K10E/K10i/K10U/K10DC
Preliminary Data Sheet
Aug.9, 2005
Note 1: Measured with a PRBS 27-1 test pattern @1.25Gbit/s and ER=9dB, BER =10-12.
Note 2: An increase in optical power above the specified level will cause the Signal Detect output to switch from a
low state to a high state.
Note 3: A decrease in optical power below the specified level will cause the Signal Detect output to switch from a
high state to a low state.
Note 4: LVPECL output, AC coupled internally, guaranteed in the full range of input optical power (-3dBm to
-27dBm)(See Recommended Interface Circuit)
Note 5: SD (See Pin Function Definitions)
Table 6 - Electrical Input/Output Coupling Mode
P/N Input(TD+/TD-)
FTM-9412P-F10/F10E/F10i/F10U
FTM-9412P-K10/K10E/K10i/K10U
Internal AC Coupling
FTM-9412P-F10DC/K10DC
Internal DC Coupling
Output(RD+/RD-)
Internal AC Coupling
Internal AC Coupling
Table 7- 1550nm Optical Signal Rejection Mode
P/N TX
FTM-9412P-F10/F10E/F10i/F10DC
FTM-9412P-K10/K10E/K10i/K10DC
1310-window
FTM-9412P-F10U/K10U
1310-window
RX
1490-window
1490/1550-window
TX_BRST
TEN_DUR
TDIS_DUR
TD+
TD-
Optical
Power
Output
ER for CM
operation
Average Power
<=-45dBm
TBURST_ON
Burst On Condition
ER and Average
Power within 15%
CM operation
TBURST_OFF
Burst Off Condition
Figure 1 Timing Parameter Definition in Burst Mode Sequence
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute
Page 5 of 15
Doc No: DS3493000-3a
5 Page SFF GE-PON PX10 ONU Transceiver
10km transmission
FTM-9412P-F10/F10E/F10i/F10U/F10DC
FTM-9412P-K10/K10E/K10i/K10U/K10DC
Preliminary Data Sheet
Aug.9, 2005
11
VCCT
Transmitter Power Supply
12
VEET
Transmitter Signal Ground
13
TX_DIS
Transmitter Disable
6
14 TD+ Transmitter Non-inverted Data Input
15 TD- Transmitter Inverted Data Input
4
16
VEET
Transmitter Signal Ground
17
TX_BRST
Transmitter Burst Control
3
18
LAS_nFAIL
Laser Failure Alarm Indication
7
19
DEBUG PORT#1
Reserved For Module Debugging
20
DEBUG PORT#2
Reserved For Module Debugging
8
F MS Mounting Studs
5
Note 1: TTL logic output, with internal 10KΩ pull-up resistor.
Optical Signal-Detected: High; Optical Signal Loss: Low
Note 2: LVPECL logic output, AC coupled internally. (See Recommended Interface Circuit)
Note 3: A positive level enable optical signal output under burst mode.
(See Timing Parameter Definition in Burst Mode Sequence)
Note 4: Compatible with LVPECL/CML input
(See Recommended Interface Circuit and Table 6 - Electrical Input/Output Coupling Mode)
Note 5: The mounting studs are provided for transceiver mechanical attachment to circuit board. They may also
provide an optional connection of the transceiver to the equipment chassis ground. The holes in the circuit
board must be tied to chassis ground. It is not recommended that the mounting studs be connected to
signal ground.
Note 6: LVTTL logic input, with internal 10KΩ pull-up resistor.
Transmitter Disabled: High; Transmitter Enabled: Low
Note 7: TTL logic output, pulled up by a 4.7-10KΩ resistor on the host board.
Laser Normal State: High; Laser Failure State: Low
Note 8: Reserved for module tuning and compulsive for system application that any circuit doesn’t be connected to
them.
Mechanical Design Diagram
The form factor is 2×5/2×10 SFF with pigtail fiber. The pigtail fiber has a length 520 - 550mm and 30mm minimum
bending radius. The fiber connector type is SC/UPC. The mechanical design diagram is shown in Figure 7 and
Figure 8. (Dimension in mm)
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute
Page 11 of 15
Doc No: DS3493000-3a
11 Page |
Páginas | Total 15 Páginas | |
PDF Descargar | [ Datasheet FTM-9412P-K10E.PDF ] |
Número de pieza | Descripción | Fabricantes |
FTM-9412P-K10 | (FTM-9412P-x10xx) SFF GE-PON Px10 ONU Transceiver | Fiberxon |
FTM-9412P-K10DC | (FTM-9412P-x10xx) SFF GE-PON Px10 ONU Transceiver | Fiberxon |
FTM-9412P-K10E | (FTM-9412P-x10xx) SFF GE-PON Px10 ONU Transceiver | Fiberxon |
FTM-9412P-K10i | (FTM-9412P-x10xx) SFF GE-PON Px10 ONU Transceiver | Fiberxon |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |