DataSheet.es    

PDF t-51832d064j Datasheet ( Hoja de datos )

Número de pieza t-51832d064j
Descripción LCD_Module
Fabricantes OPTREX 
Logotipo OPTREX Logotipo

Total 19 Páginas
		
t-51832d064j Hoja de datos, Descripción, Manual
om First Edition
.cO P T R E X
LCD Module Technical Specification
Jan 1, 2001
Final Revision
t4U ******
heeT-51382D064J-FW-P-AA
taS Checked by (Quality Assurance Div.)
.Da Checked by (Design Engineering Div.)
www Prepared by (Production Div.)
Table of Contents .com1. Applications........................................................................................................................................................... 2
2. Features ..................................................................................................................................................................... 2
U3. Mechanical Specifications ......................................................................................................................... 2
t44. Mechanical Drawing TFT LCD Module ..................................................................................... 3
5. Input / Output Terminals .......................................................................................................................... 4
e6. Absolute Maximum Ratings ..................................................................................................................... 6
7. Electrical Characteristics............................................................................................................................... 6
e8. Power Sequence......................................................................................................................................... 15
h9. Optical Characteristics................................................................................................................................ 16
10. Handing Cautions........................................................................................................................................... 17
S11. Reliability TEST ............................................................................................................................................. 18
ta12. Block Diagram....................................................................................................................................................19
Revision Hwistworyw.DaRev. Date
Page
Comment
T-51382D064J-FW-P-AA
www.DataSheet4U.comOPTREX CORPORATION
Page-1/19

1 page

t-51832d064j pdf
Note 5-2 : R/L is the Right/Left shift signal.
(1). R/L= High, U/D= Low
(2). R/L= Low, U/D= Low
Note 5-3 : U/D is the Up/Down shift signal.
(1). R/L= High, U/D= Low
(2). R/L= High, U/D= High
5-2) Backlight driving
Pin No Symbol
1 VL1
2 NC
3 VL2
Description
Input terminal (Hi voltage side)
No Connection
Input terminal (Low voltage side)
Remark
Note 5-4
Note 5-4 : Low voltage side of backlight inverter connects with ground of inverter circuits.
5-3) Input / Output Connector
A) LCD module connector (Reference)
DF9A-31P-1V
B) Backlight Connector
JST BHR-03VS-1
Pin No. 3
Pitch 4 mm
Red: High Voltage
White: Low Voltage
T-51382D064J-FW-P-AA
OPTREX CORPORATION
Page-5/19

5 Page

t-51832d064j arduino
7-5) Horizontal Display Position
Horizontal display position depends on the signal of DENB and the input digital image.
As the rising edge of DENB signal comes, LCD module will create a horizontal sampling
start pulse. At this time, the source driver ICs begin to sample image data and transfer
the digital image data to analogue image data by D/A inverters. Then send the analogue
image signal to the right position of active display area of the LCD panel. If DENB is low,
LCD module will set horizontal display position in default value.
Parameters
DENB Setup Time
Hold Time
Pulse Width
DENB
Horizontal
Keep
Sampling
At Start
“Low” Pulse Position
Hsync-DENB
Phase Difference
Symbol
Tes
Teh
Tepw
Thss
The
Format
All
All
All
VGA-480
VGA-400
VGA-350
Free
Format
All
Min.
10
10
2
128
96
Typ.
640
144
144
144
Max.
Tc-10
Tc-10
720
192
160
Unit
ns
ns
clock
clock
clock
clock
clock
clock
Remark
Note 7-4
Note 7-4:
In free format condition (Hsync = Positive, Vsync = Positive), if DENB is
low, the position of horizontal sampling start pulse depends on the seven
control lines of HP[6:0] Lattice iSPLSI1032E-LT70 FPGA. The starting
position is the count of { 128 + Data(HP[6:0]) } clock.
7-6) Vertical Display Position
Mode
Hsync
Vsync
VGA-480
VGA-400
VGA-350
Freedom
Mode
Negative
Negative
Positive
Positive
Negative
Positive
Negative
Positive
V-Start
Position
34
17
30
24
V-Display
480 lines
400 lines
350 lines
480 lines
Remark
Note 7-5
Note 7-6
Note 7-5:
As the format is VGA-400(Hsync = Negative, Vsync = Positive), LCD
module will adjust the display area to the center of display. At this time,
both of the upper and lower display areas have 40 blanking lines (the
display color is black). The actual display area is center 400 lines.
T-51382D064J-FW-P-AA
OPTREX CORPORATION
Page-11/19

11 Page


PáginasTotal 19 Páginas
PDF Descargar[ t-51832d064j.PDF ]

Enlace url


Hoja de datos destacado

Número de piezaDescripciónFabricantes
t-51832d064jLCD_ModuleOPTREX
OPTREX

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


www.DataSheet.es    |   2018   |  Privacy Policy  |  Contacto  |  Buscar